Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2019.09
RM32H0E _55 Steering _059605 POWER ASSIST SYSTEMS _0292301 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1551 IG Power Supply Voltage Open or short in IG power source circuit with ignition switch ON
·

EPS-IG1 fuse

·

IG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on The ECU judges the system has returned to normal or the ignition switch is turned ON again -

WIRING DIAGRAM

C416587E01
5.635,2.813 6.625,3.271 0.99,0.458 10 false Power Steering ECU Assembly 1.427,0.708 3.656,0.927 2.229,0.219 10 false from IG1-NO. 1 Relay 3.667,0.875 4.688,1.146 1.021,0.271 10 false EPS-IG1 5.281,0.708 5.708,0.917 0.427,0.208 10 false F23 5.281,2.094 5.708,2.302 0.427,0.208 10 false F68 5.375,0.521 5.802,0.729 0.427,0.208 10 false 1 5.375,1.885 5.802,2.094 0.427,0.208 10 false 2 5.677,0.708 6.104,0.917 0.427,0.208 10 false IG 5.667,2.094 6.094,2.302 0.427,0.208 10 false PGND

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER STEERING ECU ASSEMBLY)
a.
C349135C03
0.5,0.833 1,1.083 0.5,0.25 0.5,3.333 1,3.583 0.5,0.25 1.01,1.708 1.427,1.292 true 2.25,4.135 2,3.635 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.635,3.365 1.094,3.563 0.458,0.198 10 false F68 0.635,0.865 1.094,1.063 0.458,0.198 10 false F23 2.25,4.167 3,4.417 0.75,0.25 10 false PGND 0.802,1.625 1.26,1.823 0.458,0.198 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the F68 and F23 power steering ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F23-1 (IG) - Body ground Ignition switch ON 8 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F68-2 (PGND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR