Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.09–2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

ECM



WIRING DIAGRAM

C360942E01
1.302,0.979 1.719,1.167 0.417,0.188 10 false 120 Ω 5.479,0.99 5.979,1.177 0.5,0.188 10 false 120 Ω 1.979,0.625 2.396,0.813 0.417,0.188 10 false CA4H 1.969,1.146 2.385,1.333 0.417,0.188 10 false CA4L 1.052,1.646 1.469,1.833 0.417,0.188 10 false F74 1.031,1.823 2.542,2.198 1.51,0.375 10 false Central Gateway ECU (Network Gateway ECU) 2.417,0.615 2.833,0.802 0.417,0.188 10 false 18 2.427,1.156 2.844,1.344 0.417,0.188 10 false 17 4.594,0.646 5.01,0.833 0.417,0.188 10 false 13 4.583,1.156 5,1.344 0.417,0.188 10 false 26 5.25,1.646 5.667,1.833 0.417,0.188 10 false A38 5.208,1.833 5.677,2.031 0.469,0.198 10 false ECM 4.823,0.615 5.24,0.802 0.417,0.188 10 false CANH 4.823,1.156 5.24,1.344 0.417,0.188 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 60 km/h (37 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the ECM, refer to Service Bulletin.*1


*1: w/ Entry and Start System



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C366210C09
1.979,1.031 2.396,1.281 0.417,0.25 5.563,1.031 5.979,1.281 0.417,0.25 1.781,2.646 2.135,2.01 true 2.49,2.646 2.25,2.01 true 5.354,1.281 5.656,1.646 true 4.5,0.969 4.708,1.167 0.208,0.198 10 false *1 0.698,0.938 0.906,1.125 0.208,0.188 10 false *a 2.052,1.073 2.396,1.281 0.344,0.208 10 false F74 5.625,1.063 6.063,1.292 0.438,0.229 10 false F144 1.26,2.563 1.833,2.792 0.573,0.229 10 false CA4L*b 2.542,2.583 3.115,2.813 0.573,0.229 10 false CA4H*b 5.104,1.188 5.448,1.385 0.344,0.198 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
*b to ECM


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F74-18 (CA4H) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
F74-17 (CA4L) - F144-4 (CG)



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the A38 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

C366210C11
1.979,1.031 2.396,1.281 0.417,0.25 5.563,1.031 5.979,1.281 0.417,0.25 1.781,2.646 2.135,2.01 true 2.49,2.646 2.25,2.01 true 5.354,1.281 5.656,1.646 true 4.5,0.969 4.708,1.167 0.208,0.198 10 false *1 0.698,0.938 0.906,1.125 0.208,0.188 10 false *a 2.052,1.073 2.396,1.281 0.344,0.208 10 false F74 5.625,1.063 6.052,1.271 0.427,0.208 10 false F144 1.26,2.563 1.833,2.792 0.573,0.229 10 false CA4L*b 2.542,2.583 3.115,2.813 0.573,0.229 10 false CA4H*b 5.104,1.188 5.448,1.385 0.344,0.198 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
*b to ECM


Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-17 (CA4L) - F144-4 (CG)



Result:
Result Proceed to
OK (for 8NR-FTS) A
OK (for 3ZR-FAE) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))