Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › from 2019.09
RM32H0E _53 Suspension _059601 REAR SUSPENSION _0292266 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear coil spring removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Height Control Sensor

Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Rear height control sensor sub-assembly LH*1 Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 57628C 2.REMOVE REAR FLOOR SIDE MEMBER COVER LH (for 2WD)

Hide 57627A 3.REMOVE REAR FLOOR SIDE MEMBER COVER RH (for 2WD)

Hide 57628C 4.REMOVE REAR FLOOR SIDE MEMBER COVER LH (for AWD)

Hide 57627A 5.REMOVE REAR FLOOR SIDE MEMBER COVER RH (for AWD)

Hide 89408C 6.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 48231B 7.REMOVE REAR COIL SPRING

a.
C348389C02
2.125,0.823 2.354,0.823 true 2.125,1.208 2.125,0.771 2.125,0.771 2.344,0.771 true 1.156,1.646 1.156,1.344 1.156,1.344 0.927,1.344 true 0.917,1.406 1.146,1.406 true 2.052,1.229 2.281,1.417 0.229,0.188 10 true *a 1.063,1.656 1.292,1.844 0.229,0.188 10 true *a
*a Matchmark


Place matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.


b.

Loosen the nut (rear suspension member sub-assembly side) of the rear No. 2 suspension arm assembly.

NOTICE:

Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.



c.
C345079C01
1.771,1.51 2.177,1.51 false 1.865,1.854 2.271,1.854 false 2.208,1.427 2.521,1.583 0.313,0.156 10 false *a 2.302,1.771 2.615,1.927 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C365322

Remove the bolt and nut, and separate the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) from the rear axle carrier sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Slowly lower the rear No. 2 suspension arm assembly, and then remove the rear coil spring.


Hide 48259A 8.REMOVE REAR UPPER COIL SPRING INSULATOR

a.

Remove the rear upper coil spring insulator from the vehicle.


Hide 48258C 9.REMOVE REAR LOWER COIL SPRING INSULATOR

a.

Remove the rear lower coil spring insulator from the rear No. 2 suspension arm assembly.