Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL TANK (for AWD) › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293902 FUEL TANK(for AWD) A

8NR-FTS FUEL  FUEL TANK(for AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

Because the weight of the fuel tank sub-assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the components could fall down.

·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 77010 2.REMOVE FUEL TANK VENT TUBE ASSEMBLY

Hide 3.DRAIN FUEL

Hide 37100 5.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 57628C 6.REMOVE REAR FLOOR SIDE MEMBER COVER LH

a.
A393064N01
0.833,1.167 1.333,1 true 0.833,1.167 1.333,1.25 true 0.667,1.052 0.823,1.25 0.156,0.198 10 true A 2.031,0.115 2.188,0.313 0.156,0.198 10 true B

Remove the 2 bolts and 2 clips (A).


b.

Disengage the clip (B) to remove the floor side member cover LH.


Hide 57627A 7.REMOVE REAR FLOOR SIDE MEMBER COVER RH

a.
A393063N01
2.063,0.792 2.583,0.917 true 2.104,1.219 2.583,0.917 true 2.615,0.802 2.771,1 0.156,0.198 10 true A 1.26,0.104 1.417,0.302 0.156,0.198 10 true B

Remove the 2 bolts and 2 clips (A).


b.

Disengage the clip (B) to remove the rear side member cover RH.


Hide 77642A 8.REMOVE NO. 2 FUEL TANK PROTECTOR

a.
A395461

Remove the nut, 4 clips and No. 2 fuel tank protector from the fuel tank assembly.


Hide 77641A 9.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A395462

Remove the 4 clips and No. 1 fuel tank protector from the fuel tank assembly.


Hide 77754B 10.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A395465

Slide the hose clip and disconnect the charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.


Hide 11.DISCONNECT FUEL TANK BREATHER TUBE

a.
A396123

Disconnect the fuel tank breather tube from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77213E 12.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A395464

Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77026A 13.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A397745

Disconnect the fuel tube connector to remove the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 14.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A395952

Disconnect the fuel tube connector to remove the fuel tank main tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77100 15.REMOVE FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.
A393058

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A395468

Remove the 4 bolts and No. 1 fuel tank band sub-assemblies.


c.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77656B 16.REMOVE NO. 6 FUEL TANK CUSHION

A393059

a.

Remove the 3 No. 6 fuel tank cushions from the fuel tank assembly.


Hide 77754B 17.REMOVE CHARCOAL CANISTER OUTLET HOSE

a.

Disengage the clamp to remove the charcoal canister outlet hose from the fuel tank assembly.