Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.09
RM32H0E _53 Suspension _059606 TIRE PRESSURE MONITORING _0292310 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Tire pressure warning system DTCs can be checked by connecting terminals 13 (TC) and 4 (CG) of the DLC3. The DTCs are indicated by blinking the tire pressure warning light.

WIRING DIAGRAM

C270967E64
3.792,0.385 4.188,0.542 0.396,0.156 10 false PRG 5.771,0.271 5.958,0.427 0.188,0.156 10 false 5 4.198,0.271 4.385,0.427 0.188,0.156 10 false 5 1.406,2.198 1.646,2.406 0.24,0.208 10 false 33 5.948,2.323 6.156,2.479 0.208,0.156 10 false TC 1.094,2.281 1.302,2.438 0.208,0.156 10 false TC 5.729,2.219 5.906,2.375 0.177,0.156 10 false 13 5.781,2.531 5.906,2.719 0.125,0.188 10 false 4 5.958,2.656 6.198,2.813 0.24,0.156 10 false CG 6.146,3.177 6.531,3.375 0.385,0.198 10 false F144 6.135,3.354 6.521,3.51 0.385,0.156 10 false DLC3 5.354,1.156 7.104,1.646 1.75,0.49 10 false Tire Pressure Warning ECU and Receiver 2.854,0.875 3.135,1.031 0.281,0.156 10 false F15 2.854,1.052 4.573,1.688 1.719,0.635 10 false Main Body ECU (Multiplex Network Body ECU) 0.698,3.021 1.292,3.292 0.594,0.271 10 false ECM 0.719,2.844 1.083,2.99 0.365,0.146 10 false A38 0.74,3.563 2.833,3.854 2.094,0.292 10 false : CAN Communication Line 5.969,0.385 6.688,0.74 0.719,0.354 10 false PRG 5.375,0.958 5.813,1.156 0.438,0.198 10 false M23

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK DTC (C2179)

B

2.CHECK DTC (C2179)
a.

Check if DTC C2179 is output.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Trouble Codes
50001 203

Result:
Result Proceed to
DTC C2179 is not output. A
DTC C2179 is output. B



A

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)

B

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Disconnect the A38 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F144-13 (TC) - A38-33 (TC) Always Below 1 Ω
F144-13 (TC) or A38-33 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C217594C71
1.417,0.167 1.917,0.417 0.5,0.25 0.917,0.406 1.563,0.917 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.5,0.208 1.958,0.406 0.458,0.198 10 false F144 0.646,0.313 0.958,0.51 0.313,0.198 10 false CG
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F144-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT DLC3 TERMINAL VOLTAGE (TC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT DLC3 TERMINAL VOLTAGE (TC VOLTAGE)
a.

Reconnect the A38 ECM connector.


b.
C217594C72
1.469,0.25 1.969,0.5 0.5,0.25 1.552,0.906 0.958,0.479 true 2.354,1.865 1.802,1.469 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.552,0.292 2.01,0.49 0.458,0.198 10 false F144 0.677,0.365 1.135,0.563 0.458,0.198 10 false CG 2.427,1.865 2.885,2.063 0.458,0.198 10 false TC
*a Front view of DLC3


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F144-13 (TC) - F144-4 (CG) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG