The switch circuit inside the combination meter assembly turns on and off according to the steering pad switch assembly operation.
During test mode, when the steering pad switch assembly is operated, "TPMS" is selected on the multi-information display and the "ENTER" switch (steering pad switch assembly) is pressed, the tire pressure warning light illuminates, and when the "ENTER" switch (steering pad switch assembly) is not pressed, the tire pressure warning light blinks at 0.125 second intervals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C2198 | Initialization Switch (for Test Mode DTC) | Test mode procedure is performed. | ·
Steering pad switch assembly ·
Spiral cable sub-assembly ·
Wire harness or connector ·
Tire pressure warning ECU and receiver |
- |
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST
It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.
Remove the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL
Inspect the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F29 spiral cable sub-assembly connector.
Disconnect the F4 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F29-10 (+DP) - F4-28 (MSM+) | Always | Below 1 Ω |
| F29-10 (+DP) or F4-28 (MSM+) - Body ground | Always | 10 kΩ or higher |
| F29-11 (+DP2) - F4-33 (MSSL) | Always | Below 1 Ω |
| F29-11 (+DP2) or F4-33 (MSSL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M23 tire pressure warning ECU and receiver connector.
Disconnect the F4 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M23-3 (CLSW) - F4-4 (INT) | Always | Below 1 Ω |
| M23-3 (CLSW) or F4-4 (INT) - Body ground | Always | 10 kΩ or higher |
| F4-21 (ET) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F4-4 (INT) - Body ground | Ignition switch ON | 8 to 15 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG