Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on dynamic radar cruise control system operation, the forward recognition camera provides warnings to the driver by sounding the pre-collision city buzzer.

DTC C1A4A is stored when a malfunction is detected in the pre-collision city buzzer circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit
w/o Full-speed range following function:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the forward recognition camera detects a malfunction in the pre-collision city buzzer circuit for approximately 0.4 seconds or more.


w/ Full-speed range following function:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the forward recognition camera detects a malfunction in the pre-collision city buzzer circuit for approximately 0.4 seconds or more.


·

Pre-collision city buzzer

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

Harness or connector



WIRING DIAGRAM

C422423E01
0.781,0.771 1.823,0.99 1.042,0.219 10 false ECU-IG1 NO.4 1.938,1.115 3.5,1.594 1.563,0.479 10 false Pre-Collision City Buzzer 1.938,0.969 2.24,1.177 0.302,0.208 10 false F54 3.896,2.167 5.167,2.635 1.271,0.469 10 false Forward Recognition Camera 3.906,2 5.177,2.49 1.271,0.49 10 false R5 5.667,2.01 7.073,2.479 1.406,0.469 10 false Millimeter Wave Radar Sensor Assembly 4.073,0.604 4.469,0.865 0.396,0.26 10 false BZ 3.865,0.5 4.01,0.667 0.146,0.167 10 false 8 3.146,0.5 3.292,0.667 0.146,0.167 10 false 1 2.844,0.625 3.24,0.885 0.396,0.26 10 false BZ 2.229,0.604 2.625,0.865 0.396,0.26 10 false IG1 2.042,0.5 2.188,0.667 0.146,0.167 10 false 2 0.583,3.427 2.688,3.677 2.104,0.25 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle, and as a result, a DTC may be stored.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Check for DTCs of the pre-collision system.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220
HINT:
·

w/o Full-speed range following function:

The dynamic radar cruise control system only stores DTC C1A4A when the vehicle speed reaches 36 km/h (22 mph), however the pre-collision system stores this DTC at any vehicle speed. If DTC C1A4A is stored by the pre-collision system, perform troubleshooting of the pre-collision system first.

·

w/ Full-speed range following function:

The dynamic radar cruise control system only stores DTC C1A4A when the vehicle speed reaches 5 km/h (3 mph), however the pre-collision system stores this DTC at any vehicle speed. If DTC C1A4A is stored by the pre-collision system, perform troubleshooting of the pre-collision system first.




Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

2.CHECK FOR DTCs (RADAR CRUISE 2)

B

2.CHECK FOR DTCs (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).

3.

w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.

w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.




c.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Powertrain > Radar Cruise2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Stop Buzzer Skid control buzzer (stop sound) ON or OFF Buzzer can be heard
Radar Cruise Approach Alarm Buzzer Skid control buzzer (approach sound) ON or OFF Buzzer can be heard
Powertrain > Radar Cruise2 > Active Test
Tester Display
Radar Cruise Stop Buzzer
Radar Cruise Approach Alarm Buzzer

d.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

3.INSPECT TERMINAL VOLTAGE
3.INSPECT TERMINAL VOLTAGE
a.
B443157C10
1.5,0.177 1.906,0.438 0.406,0.26 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.594,0.208 2.052,0.406 0.458,0.198 10 false F54 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to pre-collision city buzzer)


Disconnect the pre-collision city buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F54-2 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Connect the pre-collision city buzzer connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - BATTERY)

4.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
a.

Disconnect the F54 pre-collision city buzzer connector.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-1 (BZ) - R5-8 (BZ) Always Below 1 Ω
F54-1 (BZ) or R5-8 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the R5 forward recognition camera connector.


e.

Connect the F54 pre-collision city buzzer connector.


Result:
Proceed to
OK
NG



OK

7.INSPECT PRE-COLLISION CITY BUZZER (CONFIRM BUZZER OPERATION)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
5.REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (RADAR CRUISE 2)
6.CHECK FOR DTCs (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Powertrain > Radar Cruise2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Stop Buzzer Skid control buzzer (stop sound) ON or OFF Buzzer can be heard
Radar Cruise Approach Alarm Buzzer Skid control buzzer (approach sound) ON or OFF Buzzer can be heard

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

7.INSPECT PRE-COLLISION CITY BUZZER (CONFIRM BUZZER OPERATION)
7.INSPECT PRE-COLLISION CITY BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the ignition switch to ON.


b.

Check if the pre-collision city buzzer is sounding.


Result:
Result Proceed to
The pre-collision city buzzer does not sound when the ignition switch to ON A
The pre-collision city buzzer sounds continuously when the ignition switch to ON B



A

8.INSPECT PRE-COLLISION CITY BUZZER (UNIT INSPECTION)

B

9.REPLACE PRE-COLLISION CITY BUZZER
8.INSPECT PRE-COLLISION CITY BUZZER (UNIT INSPECTION)


Result:
Result Proceed to
pre-collision city buzzer is abnormal A
pre-collision city buzzer is normal B



A

9.REPLACE PRE-COLLISION CITY BUZZER

B

10.CHECK FOR DTCs (RADAR CRUISE 2)
9.REPLACE PRE-COLLISION CITY BUZZER

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTCs (RADAR CRUISE 2)
10.CHECK FOR DTCs (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Powertrain > Radar Cruise2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Stop Buzzer Skid control buzzer (stop sound) ON or OFF Buzzer can be heard
Radar Cruise Approach Alarm Buzzer Skid control buzzer (approach sound) ON or OFF Buzzer can be heard

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

11.REPLACE FORWARD RECOGNITION CAMERA
11.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTCs (RADAR CRUISE 2)
12.CHECK FOR DTCs (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Powertrain > Radar Cruise2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Stop Buzzer Skid control buzzer (stop sound) ON or OFF Buzzer can be heard
Radar Cruise Approach Alarm Buzzer Skid control buzzer (approach sound) ON or OFF Buzzer can be heard

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

13.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
13.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC (RADAR CRUISE 2)
14.CLEAR DTC (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

Result:
Proceed to
NEXT



NEXT

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)