Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › 2019.09–2020.08
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0407350 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (B) judges that there is a communication problem with the blind spot monitor sensor RH (A).

DTC No. Detection Item DTC Detection Condition Trouble Area
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor RH (A)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 6 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH (B)

·

Power source circuit of blind spot monitor sensor LH (B)

·

Blind spot monitor sensor LH (B) ground circuit

·

Blind spot monitor sensor RH (A)


U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor LH (B)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 6 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor RH (A)

·

Power source circuit of blind spot monitor sensor RH (A)

·

Blind spot monitor sensor RH (A) ground circuit

·

Blind spot monitor sensor LH (B)



WIRING DIAGRAM

for TMMT Made



E334320E29
5.635,3.438 5.49,3.438 5.49,3.438 4.917,2.354 false 2.479,2.583 3.646,3.135 1.167,0.552 10 false Blind Spot Monitor Sensor RH (A) 3.49,4.156 5.667,4.563 2.177,0.406 10 false Clearance Warning ECU Assembly 5.698,3.51 6.615,3.99 0.917,0.479 10 false No. 6 Junction Connector 3.125,0.948 3.635,1.156 0.51,0.208 10 false CA2P 4.552,3.281 5.24,3.479 0.688,0.198 10 false CANL 3.125,1.781 3.646,2 0.521,0.219 10 false CA2N 4.115,3.281 5.156,3.823 1.042,0.542 10 false CANH 5.563,0.948 6.094,1.125 0.531,0.177 10 false CA2P 5.563,1.792 6.104,1.958 0.542,0.167 10 false CA2N 2.521,1.927 3.01,2.094 0.49,0.167 10 false BRGD 6.146,1.969 6.635,2.177 0.49,0.208 10 false BLGD 6.25,1.229 6.635,1.406 0.385,0.177 10 false BLB 2.521,1.229 3.01,1.438 0.49,0.208 10 false BRB 5.385,0.948 5.531,1.125 0.146,0.177 10 false 1 3.563,0.948 3.708,1.125 0.146,0.177 10 false 1 3.573,1.573 3.719,1.75 0.146,0.177 10 false 6 5.396,1.583 5.542,1.76 0.146,0.177 10 false 6 2.49,2.406 2.854,2.583 0.365,0.177 10 false M63 6.583,1.865 6.927,2.115 0.344,0.25 10 false 10 2.365,1.135 2.51,1.313 0.146,0.177 10 false 5 6.604,1.125 6.75,1.302 0.146,0.177 10 false 5 5.542,2.406 5.854,2.594 0.313,0.188 10 false M62 3.5,3.99 3.865,4.177 0.365,0.188 10 false F142 4.198,3.063 4.479,3.24 0.281,0.177 10 false 37 4.698,3.063 4.958,3.219 0.26,0.156 10 false 38 5.698,3.354 6.146,3.573 0.448,0.219 10 false M104 3.927,0.948 4.188,1.24 0.26,0.292 10 false 6 4.969,0.948 5.188,1.146 0.219,0.198 10 false 7 4.281,2.417 4.427,2.594 0.146,0.177 10 false 5 4.938,1.583 5.229,1.813 0.292,0.229 10 false 18 4.667,2.417 4.99,2.656 0.323,0.24 10 false 16 3.958,1.573 4.229,1.792 0.271,0.219 10 false 17 2.313,1.823 2.656,2.052 0.344,0.229 10 false 10 1.292,0.615 2.292,0.948 1,0.333 10 false ECU-IG1 NO. 4 0.125,0.49 1.104,0.979 0.979,0.49 10 false from IG1-NO. 1 Relay 5.552,2.563 6.729,2.958 1.177,0.396 10 false Blind Spot Monitor Sensor LH (B)

for TMC Made


E334320E30
5.635,3.438 5.49,3.438 5.49,3.438 4.917,2.354 false 2.479,2.583 3.646,3.135 1.167,0.552 10 false Blind Spot Monitor Sensor RH (A) 3.49,4.156 5.667,4.563 2.177,0.406 10 false Clearance Warning ECU Assembly 5.698,3.51 6.615,3.99 0.917,0.479 10 false No. 6 Junction Connector 3.125,0.948 3.635,1.156 0.51,0.208 10 false CA2P 4.552,3.281 5.24,3.479 0.688,0.198 10 false CANL 3.125,1.781 3.646,2 0.521,0.219 10 false CA2N 4.115,3.281 5.156,3.823 1.042,0.542 10 false CANH 5.563,0.948 6.094,1.125 0.531,0.177 10 false CA2P 5.563,1.792 6.104,1.958 0.542,0.167 10 false CA2N 2.521,1.927 3.01,2.094 0.49,0.167 10 false BRGD 6.146,1.969 6.635,2.177 0.49,0.208 10 false BLGD 6.25,1.229 6.635,1.406 0.385,0.177 10 false BLB 2.521,1.229 3.01,1.438 0.49,0.208 10 false BRB 5.385,0.948 5.531,1.125 0.146,0.177 10 false 1 3.563,0.948 3.708,1.125 0.146,0.177 10 false 1 3.573,1.573 3.719,1.75 0.146,0.177 10 false 6 5.396,1.583 5.542,1.76 0.146,0.177 10 false 6 2.49,2.406 2.854,2.583 0.365,0.177 10 false M63 6.583,1.865 6.927,2.115 0.344,0.25 10 false 10 2.365,1.135 2.51,1.313 0.146,0.177 10 false 5 6.604,1.125 6.75,1.302 0.146,0.177 10 false 5 5.542,2.406 5.854,2.594 0.313,0.188 10 false M62 3.5,3.99 3.865,4.177 0.365,0.188 10 false F142 4.198,3.063 4.479,3.24 0.281,0.177 10 false 37 4.698,3.063 4.958,3.219 0.26,0.156 10 false 38 5.698,3.354 6.146,3.573 0.448,0.219 10 false M104 3.948,0.948 4.208,1.24 0.26,0.292 10 false 3 4.969,0.948 5.188,1.146 0.219,0.198 10 false 2 4.281,2.417 4.427,2.594 0.146,0.177 10 false 5 4.938,1.583 5.229,1.813 0.292,0.229 10 false 13 4.667,2.417 4.99,2.656 0.323,0.24 10 false 16 3.958,1.573 4.229,1.792 0.271,0.219 10 false 14 2.313,1.823 2.656,2.052 0.344,0.229 10 false 10 1.292,0.615 2.292,0.948 1,0.333 10 false ECU-IG1 NO. 4 0.125,0.49 1.104,0.979 0.979,0.49 10 false from IG1-NO. 1 Relay 5.552,2.563 6.729,2.958 1.177,0.396 10 false Blind Spot Monitor Sensor LH (B)


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 is only output A
DTC U117887 is only output B
DTC U117787 and U117887 are output C



A

2.CHECK CAN BUS MAIN WIRE

B

5.CHECK CAN BUS MAIN WIRE

C

8.CHECK CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
2.CHECK CAN BUS MAIN WIRE
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.
E359601C53
1.5,0.208 1.885,0.438 0.385,0.229 1.667,1.698 1.427,1.177 true 0.948,1.479 1.427,1.052 true 1.563,0.25 2.021,0.448 0.458,0.198 10 false M63 0.698,1.521 1.188,1.75 0.49,0.229 10 false CA2P 1.531,1.74 2.021,1.969 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 6 JUNCTION CONNECTOR)

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 6 JUNCTION CONNECTOR)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CAN BUS MAIN WIRE
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.
E359601C55
1.5,0.208 1.885,0.438 0.385,0.229 0.969,1.51 1.438,1.052 true 1.667,1.719 1.448,1.177 true 1.573,0.25 2.031,0.448 0.458,0.198 10 false M62 0.75,1.552 1.24,1.781 0.49,0.229 10 false CA2P 1.552,1.771 2.042,2 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - M62-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 6 JUNCTION CONNECTOR)

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BODY GROUND)

OK

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) POWER SOURCE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - NO. 6 JUNCTION CONNECTOR)

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) POWER SOURCE)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
E334331C26
1.542,2.865 2.042,3.146 0.5,0.281 0.229,1.448 0.688,1.729 0.458,0.281 2.135,1.854 2.51,2.385 true 1.25,2.979 1.625,3.51 true 2.385,3.938 2.635,4.271 true 2.104,1.594 2.708,1 true 1.688,1.594 2.677,0.438 true 0.927,2.417 1.667,1.885 true 0.24,2.708 0.552,2.865 0.313,0.156 10 false *1 0.167,0.115 0.479,0.271 0.313,0.156 10 false *a 1.625,2.917 2.354,3.281 0.729,0.365 10 false F144 0.292,1.51 0.677,1.708 0.385,0.198 10 false M104 2.771,0.906 3.427,1.208 0.656,0.302 10 false CANH*B 2.385,2.427 3.24,2.677 0.854,0.25 10 false CANL*B 2.552,4.323 3.135,4.531 0.583,0.208 10 false BAT 1.094,2.76 1.677,2.969 0.583,0.208 10 false CG 0.594,2.448 1.448,2.698 0.854,0.25 10 false CANL*A 2.74,0.333 3.396,0.635 0.656,0.302 10 false CANH*A
*A for TMMT Made
*B for TMC Made
*1 DLC3
*a Component with harness connected
(No. 6 Junction Connector)


Measure the resistance according to the value(s) in the table below.

i.

for TMMT Made

Standard Resistance:
Tester Connection Condition Specified Condition Result
M104-6 (CANH) - M104-17 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
M104-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
M104-17 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
M104-6 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M104-17 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



ii.

for TMC Made

Standard Resistance:
Tester Connection Condition Specified Condition Result
M104-3 (CANH) - M104-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
M104-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
M104-14 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
M104-3 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M104-14 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short




Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

9.CONFIRM CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)

B

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR)

C

15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR)

D

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR)
9.CONFIRM CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the clearance warning ECU assembly connector.


b.
C398226C13
1.49,0.302 1.917,0.542 0.427,0.24 2.271,1.74 2.542,1.188 true 2.865,1.708 2.667,1.188 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.552,0.344 2.167,0.542 0.615,0.198 10 false F142 2.042,1.781 2.5,2.042 0.458,0.26 10 false CANH 2.74,1.74 3.198,2 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F142-38 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

10.CHECK DTC

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

10.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

b.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 and U117887 are output A
DTC U117787 and U117887 are not output B



A

B

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR)
a.
E331799C54
1.448,0.25 1.927,0.521 0.479,0.271 0.615,2.969 0.896,2.156 true 2.76,2.865 1.719,2.156 true 2.635,3.115 1.51,2.177 true 2.729,0.823 1.938,1.844 true 2.729,2.594 1.927,2.156 true 1.719,1.823 2.729,0.5 true 0.906,1.844 0.646,0.896 true 1.104,1.833 0.885,0.542 true 1.563,3.01 1.115,2.146 true 1.51,1.833 2.188,0.281 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.521,0.302 1.979,0.5 0.458,0.198 10 false M104 2.813,0.74 3.427,0.938 0.615,0.198 10 false CANH*b 2.813,0.365 3.427,0.563 0.615,0.198 10 false CANH*c 2.813,2.521 3.427,2.719 0.615,0.198 10 false CANL*b 2.802,2.792 3.417,2.99 0.615,0.198 10 false CANL*c 2.24,0.177 2.854,0.375 0.615,0.198 10 false CANH*f 2.74,3.073 3.354,3.271 0.615,0.198 10 false CANL*f 0.323,0.406 0.938,0.604 0.615,0.198 10 false CANH*e 1.677,2.948 2.292,3.146 0.615,0.198 10 false CANL*e 0.104,2.875 0.719,3.073 0.615,0.198 10 false CANL*d 0.083,0.813 0.698,1.01 0.615,0.198 10 false CANH*d
*a Front view of wire harness connector
(to No. 6 Junction Connector)
*b to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMMT Made)
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMMT Made)
*d to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMC Made)
*e to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMC Made)
*f to Clearance Warning ECU Assembly CAN Wire


Disconnect the No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

i.

for TMMT Made

Standard Resistance:
Tester Connection Condition Specified Condition
M104-7 (CANH) - M104-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-6 (CANH) - M104-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-5 (CANH) - M104-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



ii.

for TMMT Made

Standard Resistance:
Tester Connection Condition Specified Condition
M104-2 (CANH) - M104-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-3 (CANH) - M104-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-5 (CANH) - M104-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher




Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 6 JUNCTION CONNECTOR

B

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

C

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

D

14.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the No. 6 junction connector.


b.
E359601C53
1.5,0.208 1.885,0.438 0.385,0.229 1.667,1.698 1.427,1.177 true 0.948,1.479 1.427,1.052 true 1.563,0.25 2.021,0.448 0.458,0.198 10 false M63 0.698,1.521 1.188,1.75 0.49,0.229 10 false CA2P 1.531,1.74 2.021,1.969 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 6 JUNCTION CONNECTOR)

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the No. 6 junction connector.


b.
E359601C55
1.5,0.208 1.885,0.438 0.385,0.229 0.969,1.51 1.438,1.052 true 1.667,1.719 1.448,1.177 true 1.573,0.25 2.031,0.448 0.458,0.198 10 false M62 0.75,1.552 1.24,1.781 0.49,0.229 10 false CA2P 1.552,1.771 2.042,2 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - M62-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 6 JUNCTION CONNECTOR)

14.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the M104 No. 6 junction connector.


b.
C398226C13
1.49,0.302 1.917,0.542 0.427,0.24 2.271,1.74 2.542,1.188 true 2.865,1.708 2.667,1.188 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.552,0.344 2.167,0.542 0.615,0.198 10 false F142 2.042,1.781 2.5,2.042 0.458,0.26 10 false CANH 2.74,1.74 3.198,2 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F142-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR)
a.
E331799C54
1.448,0.25 1.927,0.521 0.479,0.271 0.615,2.969 0.896,2.156 true 2.76,2.865 1.719,2.156 true 2.635,3.115 1.51,2.177 true 2.729,0.823 1.938,1.844 true 2.729,2.594 1.927,2.156 true 1.719,1.823 2.729,0.5 true 0.906,1.844 0.646,0.896 true 1.104,1.833 0.885,0.542 true 1.563,3.01 1.115,2.146 true 1.51,1.833 2.188,0.281 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.521,0.302 1.979,0.5 0.458,0.198 10 false M104 2.813,0.74 3.427,0.938 0.615,0.198 10 false CANH*b 2.813,0.365 3.427,0.563 0.615,0.198 10 false CANH*c 2.813,2.521 3.427,2.719 0.615,0.198 10 false CANL*b 2.802,2.792 3.417,2.99 0.615,0.198 10 false CANL*c 2.24,0.177 2.854,0.375 0.615,0.198 10 false CANH*f 2.74,3.073 3.354,3.271 0.615,0.198 10 false CANL*f 0.323,0.406 0.938,0.604 0.615,0.198 10 false CANH*e 1.677,2.948 2.292,3.146 0.615,0.198 10 false CANL*e 0.104,2.875 0.719,3.073 0.615,0.198 10 false CANL*d 0.083,0.813 0.698,1.01 0.615,0.198 10 false CANH*d
*a Front view of wire harness connector
(to No. 6 Junction Connector)
*b to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMMT Made)
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMMT Made)
*d to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMC Made)
*e to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMC Made)
*f to Clearance Warning ECU Assembly CAN Wire


Disconnect the No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

i.

for TMMT Made

Standard Resistance:
Tester Connection Condition Specified Condition
M104-7 (CANH) - M104-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-6 (CANH) - M104-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-5 (CANH) - M104-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



ii.

for TMMT Made

Standard Resistance:
Tester Connection Condition Specified Condition
M104-2 (CANH) - M104-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-3 (CANH) - M104-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M104-5 (CANH) - M104-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher




Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 6 JUNCTION CONNECTOR

B

16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

18.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the M104 No. 6 junction connector.


b.
E359601C55
1.5,0.208 1.885,0.438 0.385,0.229 0.969,1.51 1.438,1.052 true 1.667,1.719 1.448,1.177 true 1.573,0.25 2.031,0.448 0.458,0.198 10 false M62 0.75,1.552 1.24,1.781 0.49,0.229 10 false CA2P 1.552,1.771 2.042,2 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - M62-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 6 JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the M104 No. 6 junction connector.


b.
E359601C53
1.5,0.208 1.885,0.438 0.385,0.229 1.667,1.698 1.427,1.177 true 0.948,1.479 1.427,1.052 true 1.563,0.25 2.021,0.448 0.458,0.198 10 false M63 0.698,1.521 1.188,1.75 0.49,0.229 10 false CA2P 1.531,1.74 2.021,1.969 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 6 JUNCTION CONNECTOR)

18.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the M104 No. 6 junction connector.


b.
C398226C13
1.49,0.302 1.917,0.542 0.427,0.24 2.271,1.74 2.542,1.188 true 2.865,1.708 2.667,1.188 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.552,0.344 2.167,0.542 0.615,0.198 10 false F142 2.042,1.781 2.5,2.042 0.458,0.26 10 false CANH 2.74,1.74 3.198,2 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F142-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the M104 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

E348217C15
1.99,0.49 2.438,0.75 0.448,0.26 5.479,0.479 5.927,0.74 0.448,0.26 5.792,1.26 6.135,0.844 6.135,0.844 6.323,0.844 true 6.49,1.792 6.406,2.385 6.406,2.385 6.594,2.385 true 1.01,2.115 1.583,1.729 true 1.125,2.5 1.74,1.74 true 2.958,2.573 2.052,1.74 true 3.281,2.313 2.198,1.719 true 3.302,2 2.354,1.74 true 2.354,1.479 3.385,1.073 true 2.198,1.49 3.26,0.688 true 2.052,1.49 3.167,0.323 true 1.74,1.49 1.208,0.802 true 1.594,1.479 1.125,1.146 true 4.563,0.313 4.875,0.469 0.313,0.156 10 false *1 0.104,0.25 0.417,0.406 0.313,0.156 10 false *a 0.531,1.01 1.198,1.25 0.667,0.24 10 false CANH*d 3.281,0.198 3.844,0.458 0.563,0.26 10 false CANH*f 0.615,0.615 1.25,0.854 0.635,0.24 10 false CANH*e 2.052,0.542 2.51,0.74 0.458,0.198 10 false M104 5.563,0.531 6.094,0.74 0.531,0.208 10 false F144 6.656,2.333 7.083,2.552 0.427,0.219 10 false BAT 6.375,0.771 6.646,0.979 0.271,0.208 10 false CG 0.573,2.406 1.24,2.646 0.667,0.24 10 false CANL*e 3.354,2.208 3.917,2.469 0.563,0.26 10 false CANL*c 3.052,2.51 3.688,2.75 0.635,0.24 10 false CANL*f 3.385,1.927 3.948,2.188 0.563,0.26 10 false CANL*b 0.448,2.052 1.115,2.292 0.667,0.24 10 false CANL*d 3.344,0.594 3.906,0.854 0.563,0.26 10 false CANH*c 3.458,0.958 4.021,1.219 0.563,0.26 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 Junction Connector)
*b to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMMT Made)
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMMT Made) *d to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMC Made)
*e to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMC Made) *f to Clearance Warning ECU Assembly CAN Wire


i.

for TMMT Made

Standard Resistance:
Tester Connection Condition Specified Condition
M104-7 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-18 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-7 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-18 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-17 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-6 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-17 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-16 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-5 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-16 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



ii.

for TMC Made

Standard Resistance:
Tester Connection Condition Specified Condition
M104-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-13 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-2 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-13 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-14 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-3 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-14 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-16 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M104-5 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M104-16 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 6 JUNCTION CONNECTOR

B

20.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

22.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
20.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the M104 No. 6 junction connector.


b.

Disconnect the M62 blind spot monitor sensor LH (B) connector.


c.
E334330C93
1.479,1.813 1.958,2.115 0.479,0.302 1.396,0.198 1.792,0.49 0.396,0.292 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.313,1.813 0.625,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.552,1.885 1.958,2.146 0.406,0.26 10 false F144 1.458,0.26 1.771,0.458 0.313,0.198 10 false M62 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M62-6 (CA2N) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M62-1 (CA2P) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M62-6 (CA2N) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 6 JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the M104 No. 6 junction connector.


b.

Disconnect the M63 blind spot monitor sensor RH (A) connector.


c.
E334330C94
1.479,1.771 1.917,2.094 0.438,0.323 1.396,0.198 1.792,0.49 0.396,0.292 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.292,1.823 0.604,1.979 0.313,0.156 10 false *1 0.229,0.208 0.542,0.365 0.313,0.156 10 false *a 1.542,1.854 1.917,2.073 0.375,0.219 10 false F144 1.469,0.26 1.813,0.49 0.344,0.229 10 false M63 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M63-6 (CA2N) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M63-1 (CA2P) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M63-6 (CA2N) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 6 JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the M104 No. 6 junction connector.


b.
E348218C11
1.406,0.302 1.854,0.573 0.448,0.271 1.469,1.74 1.906,2 0.438,0.26 2.958,1.865 2.76,1.865 2.76,1.865 2.594,1.271 false 2.604,3.25 2.406,3.25 2.406,3.25 2.25,2.833 false 1.625,2.49 1.302,3.281 1.302,3.281 1.083,3.281 false 2.938,2.219 2.74,2.219 2.74,2.219 2.49,1.281 false 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 0.198,2.031 0.51,2.229 0.313,0.198 10 false *1 1.479,0.354 1.969,0.708 0.49,0.354 10 false F142 1.521,1.802 1.979,2 0.458,0.198 10 false F144 2.99,1.771 3.396,2 0.406,0.229 10 false CANL 2.979,2.156 3.385,2.385 0.406,0.229 10 false CANH 2.635,3.167 3.042,3.396 0.406,0.229 10 false BAT 0.865,3.198 1.271,3.427 0.406,0.229 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the F142 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F142-38 (CANL) - F144-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F142-37 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F142-38 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 6 JUNCTION CONNECTOR)