Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Headlight ECU) › from 2019.09
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0407374 LIGHTING SYSTEM(w/o Headlight ECU) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Headlight ECU)  Clearance Light/Daytime Running Light Circuit  


DESCRIPTION

Clearance light function:

When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the TAIL relay and illuminates the clearance lights.


Daytime running light function:

When the operation conditions of the daytime running lights are met, the main body ECU (multiplex network body ECU) sends an illumination request signal to the DRL relay and illuminates the daytime running lights.


WIRING DIAGRAM

E357705E07
2.5,0.688 2.813,0.885 0.313,0.198 10 false 11 3.771,0.698 4.083,0.896 0.313,0.198 10 false 12 3.771,1.354 4.083,1.552 0.313,0.198 10 false 10 2.531,1.365 2.844,1.563 0.313,0.198 10 false 9 4.74,0.708 5.052,0.906 0.313,0.198 10 false 28 5.729,0.698 6.042,0.896 0.313,0.198 10 false 25 5.719,0.885 6.083,1.229 0.365,0.344 10 false MB 6.021,0.771 6.563,1.094 0.542,0.323 10 false DRLE 4.719,1.365 5.792,2.052 1.073,0.688 10 false Instrument Panel Junction Block Assembly 4.75,0.896 5.115,1.24 0.365,0.344 10 false 3F 5.479,3.969 7.156,4.979 1.677,1.01 10 false Main Body ECU (Multiplex Network Body ECU) 3.771,0.896 4.135,1.24 0.365,0.344 10 false 1B 3.76,1.542 4.125,1.885 0.365,0.344 10 false 1B 2.49,1.542 2.854,1.885 0.365,0.344 10 false 1B 2.51,0.885 2.875,1.229 0.365,0.344 10 false 1B 1.594,1.073 2.135,1.396 0.542,0.323 10 false DRL 0.25,0.865 1.281,1.26 1.031,0.396 10 false from Battery 1.656,3.552 3.531,3.938 1.875,0.385 10 false Headlight Unit Assembly LH 1.875,3.01 2.24,3.354 0.365,0.344 10 false E 2.719,3 3.083,3.344 0.365,0.344 10 false B 2.563,2.188 4.521,2.615 1.958,0.427 10 false No. 1 Integration Relay 1.667,3.406 2.833,3.615 1.167,0.208 10 false A88 2.938,2.885 3.885,3.115 0.948,0.229 10 false 4 1.688,2.875 2,3.073 0.313,0.198 10 false 6 1.635,4.813 3.042,5.115 1.406,0.302 10 false A89 1.625,4.958 3.5,5.344 1.875,0.385 10 false Headlight Unit Assembly RH 2.927,4.281 3.792,4.552 0.865,0.271 10 false 4 2.729,4.438 3.094,4.781 0.365,0.344 10 false B 1.885,4.427 2.25,4.771 0.365,0.344 10 false E 1.708,4.292 2.021,4.49 0.313,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK OPERATION (CLEARANCE LIGHS)
a.

Check the operation of the clearance lights.

OK:

The clearance lights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Body Electrical / Main Body / Active Test.

Body Electrical > Main Body > Active Test
Tester Display
Daytime Running Light
50004 123 29

d.

Perform the Active Test according to the display on the GTS.


Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Daytime Running Light Daytime running lights ON or OFF -
OK:

Daytime running lights illuminate.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A88 headlight unit assembly LH connector.


b.

Disconnect the A89 headlight unit assembly RH connector.


c.

Disconnect the 1B No. 1 Integration Relay connector.


d.

Disconnect the 3F instrument panel junction block assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A88-4 (B) - 1B-10 Always Below 1 Ω
A89-4 (B) - 1B-10 Always Below 1 Ω
A88-4 (B) or 1B-10 - Body ground Always 10 kΩ or higher
A89-4 (B) or 1B-10 - Body ground Always 10 kΩ or higher
1B-12 - 3F-28 Always Below 1 Ω
1B-12 or 3F-28 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 1 INTEGRATION RELAY (DRL RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NO. 1 INTEGRATION RELAY (DRL RELAY)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Inspect the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION

OK:

No. 1 integration relay is normal.



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E416825C10
1.74,0.583 2.115,0.833 0.375,0.25 4.875,0.938 5.25,1.188 0.375,0.25 5.542,2.063 5.917,1.552 true 0.479,0.438 0.792,0.635 0.313,0.198 10 false *a 1.844,0.635 2.156,0.833 0.313,0.198 10 false 3F 4.958,0.979 5.271,1.177 0.313,0.198 10 false MB 5.271,2.073 5.802,2.302 0.531,0.229 10 false DRL
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-28 - MB-25 (DRL) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY