Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2019.09–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P003612  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery  P003613  A/F (O2) Heater Control Circuit Bank 1 Sensor 2 Circuit Open  P003614  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open  P102A9E  O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On  


DESCRIPTION

for Rear Air Fuel Ratio Sensor Type:

Refer to DTC P013616.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P013616

for Rear Heated Oxygen Sensor Type:

Refer to DTC P013613.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P013613


for Rear Air Fuel Ratio Sensor Type:

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor (sensor 2) heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor (sensor 2).

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor (sensor 2) heater circuit uses a relay on the +B side of the circuit.

A384882E02
0.083,0.073 2.76,0.292 2.677,0.219 10 false Reference (System Diagram of Sensor 2): 0.177,1.042 0.979,1.323 0.802,0.281 10 false from Battery 0.802,1.271 1.854,1.51 1.052,0.24 10 false EFI-MAIN NO. 1 1.906,2.969 2.938,3.365 1.031,0.396 10 false No. 1 Integration Relay 2.073,2.365 2.792,2.833 0.719,0.469 10 false EFI-MAIN 2.99,1.271 3.677,1.51 0.688,0.24 10 false EFI NO. 3 3.458,0.99 3.865,1.208 0.406,0.219 10 false +B 3.323,1.552 3.719,1.771 0.396,0.219 10 false A1B- 3.906,1.281 4.417,1.49 0.51,0.208 10 false Heater 4.521,1 4.927,1.219 0.406,0.219 10 false HA1B 4.542,1.552 4.948,1.771 0.406,0.219 10 false A1B+ 3.844,1.896 4.354,2.104 0.51,0.208 10 false Sensor 3.531,2.25 4.865,2.646 1.333,0.396 10 false Air Fuel Ratio Sensor (Sensor 2) 5.125,0.99 5.531,1.208 0.406,0.219 10 false HA1B 5.135,1.552 5.542,1.771 0.406,0.219 10 false A1B+ 5.125,2.563 5.531,2.781 0.406,0.219 10 false A1B 5.125,2.99 5.531,3.208 0.406,0.219 10 false MREL 5.76,3.49 6.167,3.708 0.406,0.219 10 false ECM



for Rear Heated Oxygen Sensor Type:

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A384882E01
0.083,0.073 2.76,0.292 2.677,0.219 10 false Reference (System Diagram of Sensor 2): 0.177,1.042 0.979,1.323 0.802,0.281 10 false from Battery 0.802,1.271 1.854,1.51 1.052,0.24 10 false EFI-MAIN NO. 1 1.906,2.969 2.938,3.365 1.031,0.396 10 false No. 1 Integration Relay 2.073,2.365 2.792,2.833 0.719,0.469 10 false EFI-MAIN 2.99,1.271 3.677,1.51 0.688,0.24 10 false EFI NO. 3 3.458,0.99 3.865,1.208 0.406,0.219 10 false +B 3.469,1.552 3.76,1.771 0.292,0.219 10 false E2 3.906,1.281 4.417,1.49 0.51,0.208 10 false Heater 4.521,1 4.927,1.219 0.406,0.219 10 false HT1B 4.542,1.552 4.948,1.771 0.406,0.219 10 false OX1B 3.844,1.896 4.354,2.104 0.51,0.208 10 false Sensor 3.531,2.25 5.01,2.479 1.479,0.229 10 false Heated Oxygen Sensor 5.125,0.99 5.531,1.208 0.406,0.219 10 false HT1B 5.135,1.552 5.542,1.771 0.406,0.219 10 false OX1B 5.125,2.563 5.531,2.781 0.406,0.219 10 false EX1B 5.125,2.99 5.531,3.208 0.406,0.219 10 false MREL 5.76,3.49 6.167,3.708 0.406,0.219 10 false ECM



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003612 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery for Rear air fuel ratio sensor type

The air fuel ratio sensor (sensor 2) heater current is more than the specified value while the heater is operating (1 trip detection logic).


for Rear heated oxygen sensor type

Heated oxygen sensor heater current reaches high limit (1 trip detection logic).


for Rear air fuel ratio sensor type
·

Short in air fuel ratio sensor (sensor 2) heater circuit

·

Air fuel ratio sensor (sensor 2)

·

ECM


for Rear heated oxygen sensor type
·

Short in heated oxygen sensor heater circuit

·

Heated oxygen sensor

·

ECM


Comes on DTC stored SAE Code:
P0038
P003613 A/F (O2) Heater Control Circuit Bank 1 Sensor 2 Circuit Open The air fuel ratio sensor (sensor 2) heater current is less than the specified value while the heater is operating (1 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 2) heater circuit

·

Air fuel ratio sensor (sensor 2)

·

ECM


Comes on DTC stored SAE Code:
P0037
P003614 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open or short in heated oxygen sensor heater circuit

·

Heated oxygen sensor

·

ECM


Comes on DTC stored SAE Code:
P0037
P102A9E O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On for Rear air fuel ratio sensor type

The air fuel ratio sensor (sensor 2) heater voltage is the specified value or less while the heater is not operating (1 trip detection logic).


for Rear heated oxygen sensor type

Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).


for Rear air fuel ratio sensor type
·

Short in air fuel ratio sensor (sensor 2) heater circuit

·

Air fuel ratio sensor (sensor 2)

·

ECM


for Rear heated oxygen sensor type
·

Short in heated oxygen sensor heater circuit

·

ECM


Comes on DTC stored SAE Code:
P102D

MONITOR DESCRIPTION

for Rear Air Fuel Ratio Sensor Type:

The air fuel ratio sensor (sensor 2) detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor (sensor 2) is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful current signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor (sensor 2) becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

Air Fuel Ratio Sensor (Sensor 2) Heater Range Check (P003612 and P003613):

The ECM monitors the current applied to the air fuel ratio sensor (sensor 2) heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor (sensor 2) becomes inaccurate. When the current in the air fuel ratio sensor (sensor 2) heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



Air Fuel Ratio Sensor (Sensor 2) Heater Performance (P102A9E):

When the air fuel ratio sensor (sensor 2) heater terminal voltage is the specified value or less while the heater is not operating, the ECM determines that there is a malfunction in the sensor heater and stores DTC.



for Rear Heated Oxygen Sensor Type:

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P003612, P003614 and P102A9E):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

for Rear Air Fuel Ratio Sensor Type:

P003613
Output duty cycle 30% or higher

P003612
Output duty cycle Higher than 5%

P102A9E
Output duty cycle Less than 95%

for Rear Heated Oxygen Sensor Type:

Time after heater on 10 seconds or more

CONFIRMATION DRIVING PATTERN

A262623E03
0.792,0.969 1.438,1.167 0.646,0.198 10 3000 rpm 1.031,1.74 1.417,1.99 0.385,0.25 10 Idling 0.229,2.01 1.396,2.354 1.167,0.344 10 Ignition Switch ON 1.927,2.135 2.198,2.396 0.271,0.26 10 [A] 2.76,1.625 2.979,1.927 0.219,0.302 10 [B] 4.021,0.865 4.302,1.135 0.281,0.271 10 [C] 5.385,1.604 5.615,1.885 0.229,0.281 10 [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 5 minutes or more 3.854,2.615 4.427,2.781 0.573,0.167 10 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

9.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

10.

Idle the engine for 5 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P003612, P003613, P003614 or P102A9E

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A384823E15
0.49,2.865 1.563,3.063 1.073,0.198 10 false Battery 1.094,4.25 2.167,4.448 1.073,0.198 10 false *3: Shielded 3.604,0.833 3.958,1.021 0.354,0.188 10 false +B 3.604,1.604 3.958,1.792 0.354,0.188 10 false A1B- 4.229,0.833 4.646,1.021 0.417,0.188 10 false HA1B 4.26,1.604 4.656,1.802 0.396,0.198 10 false A1B+ 3.688,2.344 4.833,2.823 1.146,0.479 10 false Air Fuel Ratio Sensor (Sensor 2) 5.115,3.365 5.469,3.552 0.354,0.188 10 false *3 6.073,0.823 6.615,1.01 0.542,0.188 10 false HA1B 6.073,1.573 6.594,1.76 0.521,0.188 10 false A1B+ 6.063,2.802 6.469,3.01 0.406,0.208 10 false A1B- 6.063,3.896 6.615,4.073 0.552,0.177 10 false MREL 6.354,4.365 6.917,4.563 0.563,0.198 10 false ECM 5.698,0.917 6.115,1.104 0.417,0.188 10 false C62 5.729,0.719 6.146,0.906 0.417,0.188 10 false 52 5.75,1.49 6.167,1.677 0.417,0.188 10 false 99 5.688,2.698 6.104,2.885 0.417,0.188 10 false 100 5.698,1.698 6.115,1.885 0.417,0.188 10 false C62 5.698,2.906 6.115,3.094 0.417,0.188 10 false C62 5.75,3.802 6.167,3.99 0.417,0.188 10 false 46 5.698,4.021 6.115,4.208 0.417,0.188 10 false A38 4.688,0.823 4.854,1.073 0.167,0.25 10 false 1 4.698,1.594 4.865,1.844 0.167,0.25 10 false 3 3.448,0.823 3.615,1.073 0.167,0.25 10 false 2 3.448,1.594 3.615,1.844 0.167,0.25 10 false 4 3.667,2.188 4.094,2.385 0.427,0.198 10 false C72 2.656,1.052 3.406,1.219 0.75,0.167 10 false EFI NO. 3 0.427,1.063 1.542,1.406 1.115,0.344 10 false EFI-MAIN NO. 1 1.729,2 2.542,2.24 0.813,0.24 10 false EFI-MAIN 0.323,1.917 2.156,2.115 1.833,0.198 10 false BATT MAIN 1.365,1.396 1.708,1.708 0.344,0.313 10 false 5*1 2.521,1.406 2.844,1.625 0.323,0.219 10 false 6*1 1.5,0.833 1.656,1.031 0.156,0.198 10 false 3 2.51,0.833 2.667,1.031 0.156,0.198 10 false 4 1.604,2.51 2.417,2.75 0.813,0.24 10 false 1B 1.615,2.698 3.094,2.99 1.479,0.292 10 false No. 1 Integration Relay 0.094,0.104 3.01,0.438 2.917,0.333 12 false for Rear Air Fuel Ratio Sensor Type: 1.083,3.417 3.688,3.615 2.604,0.198 10 false *1: for TMMT made 1.083,3.833 3.531,4.031 2.448,0.198 10 false *2: for TMC made 1.365,1.563 1.75,1.917 0.385,0.354 10 false 6*2 2.521,1.563 2.917,1.833 0.396,0.271 10 false 5*2

A384823E16
0.49,2.865 1.563,3.063 1.073,0.198 10 false Battery 1.177,4.25 2.25,4.448 1.073,0.198 10 false *3: Shielded 3.604,0.833 3.958,1.021 0.354,0.188 10 false +B 3.615,1.604 3.969,1.792 0.354,0.188 10 false E2 4.271,0.833 4.74,1.031 0.469,0.198 10 false HT1B 4.271,1.604 4.74,1.802 0.469,0.198 10 false OX1B 3.677,2.344 4.677,2.792 1,0.448 10 false Heated Oxygen Sensor 5.115,3.365 5.469,3.552 0.354,0.188 10 false *3 6.073,0.823 6.615,1.01 0.542,0.188 10 false HT1B 6.073,1.573 6.594,1.76 0.521,0.188 10 false OX1B 6.063,2.802 6.583,2.99 0.521,0.188 10 false EX1B 6.063,3.896 6.615,4.073 0.552,0.177 10 false MREL 6.354,4.365 6.917,4.563 0.563,0.198 10 false ECM 5.698,0.917 6.115,1.104 0.417,0.188 10 false C62 5.729,0.719 6.146,0.906 0.417,0.188 10 false 17 5.75,1.49 6.167,1.677 0.417,0.188 10 false 99 5.688,2.698 6.104,2.885 0.417,0.188 10 false 100 5.698,1.698 6.115,1.885 0.417,0.188 10 false C62 5.698,2.906 6.115,3.094 0.417,0.188 10 false C62 5.75,3.802 6.167,3.99 0.417,0.188 10 false 46 5.698,4.021 6.115,4.208 0.417,0.188 10 false A38 4.688,0.823 4.854,1.073 0.167,0.25 10 false 1 4.698,1.594 4.865,1.844 0.167,0.25 10 false 3 3.448,0.823 3.615,1.073 0.167,0.25 10 false 2 3.448,1.594 3.615,1.844 0.167,0.25 10 false 4 3.667,2.188 4.083,2.438 0.417,0.25 10 false C49 2.656,1.052 3.406,1.219 0.75,0.167 10 false EFI NO. 3 0.427,1.063 1.542,1.406 1.115,0.344 10 false EFI-MAIN NO. 1 1.729,2 2.542,2.24 0.813,0.24 10 false EFI-MAIN 0.323,1.917 2.156,2.115 1.833,0.198 10 false BATT MAIN 1.354,1.396 1.667,1.583 0.313,0.188 10 false 5*1 2.521,1.365 2.875,1.573 0.354,0.208 10 false 6*1 1.5,0.833 1.656,1.031 0.156,0.198 10 false 3 2.51,0.833 2.667,1.031 0.156,0.198 10 false 4 1.604,2.51 2.417,2.75 0.813,0.24 10 false 1B 1.615,2.698 3.094,2.99 1.479,0.292 10 false No. 1 Integration Relay 0.115,0.083 3.177,0.375 3.063,0.292 12 false for Rear Heated Oxygen Sensor Type: 1.167,3.417 3.771,3.615 2.604,0.198 10 false *1: for TMMT made 1.167,3.833 3.615,4.031 2.448,0.198 10 false *2: for TMC made 1.354,1.573 1.688,1.781 0.333,0.208 10 false 6*2 2.521,1.563 2.813,1.76 0.292,0.198 10 false 5*2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


for Rear Air Fuel Ratio Sensor Type:

HINT:
·

Refer to "Data List / Active Test" [A/F Sensor Heater Duty B1S2 and A/F Sensor Heater Duty B2S2].

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor (sensor 2) output current (Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P013616). If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



for Rear Heated Oxygen Sensor Type:

HINT:
·

Refer to "Data List / Active Test" [O2 Sensor Heater B1S2 and O2 Sensor Heater Current Value B1S2].

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

When the values for the Data List item O2 Sensor Heater Current Value B1S2 is not 0 A, the heater is on.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P013613). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for Rear air fuel ratio sensor type A
for Rear heated oxygen sensor type B




A

2.INSPECT AIR FUEL RATIO SENSOR (SENSOR 2) (HEATER RESISTANCE)

B

7.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
2.INSPECT AIR FUEL RATIO SENSOR (SENSOR 2) (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 2))

NG

REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 2))
a.

Disconnect the air fuel ratio sensor (sensor 2) connector.


b.

Turn the ignition switch to ON.


c.
A217282C43
0.688,2.125 1.073,2.396 0.385,0.271 1.896,2.188 2.573,1.698 true 0.75,2.167 1.063,2.375 0.313,0.208 10 false C72 0.156,0.083 0.417,0.302 0.26,0.219 10 false *a 2.625,1.615 2.917,1.802 0.292,0.188 10 false +B
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor (Sensor 2))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C72-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 2) - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 2) - ECM)
a.

Disconnect the C72 air fuel ratio sensor (sensor 2) connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C72-1 (HA1B) - C62-52 (HA1B) Always Below 1 Ω
C72-1 (HA1B) or C62-52 (HA1B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003613 or P102A9E)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003613 or P102A9E)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P003612, P003613 or P102A9E is output B




A

B

7.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
A217282C36
0.688,2.125 1.073,2.396 0.385,0.271 1.896,2.188 2.573,1.698 true 0.75,2.167 1.292,2.552 0.542,0.385 10 false C49 0.156,0.083 0.417,0.302 0.26,0.219 10 false *a 2.625,1.615 2.917,1.802 0.292,0.188 10 false +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


a.

Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C49-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the C49 heated oxygen sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C49-1 (HT1B) - C62-17 (HT1B) Always Below 1 Ω
C49-1 (HT1B) or C62-17 (HT1B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614 OR P102A9E)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614 OR P102A9E)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P003612, P003614 or P102A9E is output B




A

B