Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P042000  Catalyst System Efficiency Below Threshold Bank 1  


MONITOR DESCRIPTION

for Rear Air Fuel Ratio Sensor Type

The ECM uses air fuel ratio sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor (sensor 1), sends pre-catalyst information to the ECM. The second sensor, the air fuel ratio sensor (sensor 2), sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the air fuel ratio sensor (sensor 2) while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the air fuel ratio sensor (sensor 2) is long, the oxygen storage capacity is great. There is a direct correlation between the air fuel ratio sensor (sensor 2) and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM will illuminate the MIL and store a DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.


for Rear Heated Oxygen Sensor Type

The ECM uses air fuel ratio sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM will illuminate the MIL and store a DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P042000 Catalyst System Efficiency Below Threshold Bank 1 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). for Rear air fuel ratio sensor type
·

Gas leak from exhaust system

·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Converter assembly (TWC: Front catalyst)

·

Front exhaust pipe assembly (TWC: Rear catalyst)


for Rear heated oxygen sensor type
·

Gas leak from exhaust system

·

Air fuel ratio sensor (sensor 1)

·

Heated oxygen sensor

·

Exhaust manifold converter sub-assembly (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)


Comes on (Euro-OBD) / - (Except Euro-OBD) DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
P0420

CATALYST LOCATION

w/ Differential Pressure Sensor


A404622C01
5.833,3.917 5.667,3.917 5.667,3.917 5,2.833 true 1.667,0.917 1.917,0.583 1.917,0.583 2.083,0.583 true 1.667,2.083 2.25,1.667 2.25,1.667 2.417,1.667 true 3.417,4.583 3.25,4.583 3.25,4.583 2.5,3.583 true 1.583,4.906 1.917,5.24 1.917,5.24 2.083,5.24 true 2.125,0.51 2.438,0.708 0.313,0.198 10 false *1 2.458,1.563 2.771,1.76 0.313,0.198 10 false *2 3.458,4.521 3.771,4.719 0.313,0.198 10 false *3 2.125,5.156 2.438,5.354 0.313,0.198 10 false *4 5.854,3.833 6.167,4.031 0.313,0.198 10 false *5 0.063,0.083 0.438,0.323 0.375,0.24 12 false *A
*A for 2WD - -
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*3 Front Exhaust Pipe Assembly (TWC: Rear Catalyst) *4 Air Fuel Ratio Sensor (Sensor 2)
*5 Tail Exhaust Pipe Assembly - -


A404623C01
0.833,3.583 1.333,2.917 1.333,2.917 1.5,2.917 true 1.25,5.333 1.083,5.333 1.083,5.333 0.667,4.75 true 1.167,0.833 1.5,0.583 1.5,0.583 1.667,0.583 true 1.083,1.75 1.917,1.417 1.917,1.417 2.083,1.417 true 2.667,3.5 3.25,2.5 3.25,2.5 3.417,2.5 true 5.5,3.917 5.333,3.917 5.333,3.917 4.74,3.219 true 1.688,0.49 2,0.688 0.313,0.198 10 false *1 2.115,1.344 2.427,1.542 0.313,0.198 10 false *2 1.51,2.823 1.823,3.021 0.313,0.198 10 false *3 1.281,5.26 1.594,5.458 0.313,0.198 10 false *4 3.458,2.385 3.771,2.583 0.313,0.198 10 false *5 5.542,3.875 5.854,4.073 0.313,0.198 10 false *6 0.063,0.052 0.438,0.292 0.375,0.24 12 false *A
*A for AWD - -
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*3 Front Exhaust Pipe Assembly *4 Air Fuel Ratio Sensor (Sensor 2)
*5 Front Exhaust Pipe Assembly (TWC: Rear Catalyst) *6 Tail Exhaust Pipe Assembly



w/o Differential Pressure Sensor (for Rear Air Fuel Ratio Sensor Type)


A384803C03
1.385,1.125 1.719,0.708 1.719,0.708 1.885,0.708 true 1.26,2.073 1.594,1.656 1.594,1.656 1.76,1.656 true 2.406,3.344 2.708,2.938 2.708,2.938 2.875,2.938 true 1.563,4.583 1.896,5 1.896,5 2.063,5 true 4.865,2.854 5.198,3.271 5.198,3.271 5.365,3.271 true 0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 1.979,0.604 2.292,0.76 0.313,0.156 10 false *1 1.833,1.552 2.146,1.708 0.313,0.156 10 false *2 2.948,2.833 3.26,2.99 0.313,0.156 10 false *3 2.125,4.927 2.719,5.167 0.594,0.24 10 false *4(*B) 5.438,3.167 5.75,3.323 0.313,0.156 10 false *5
*A for 2WD *B for Rear Air Fuel Ratio Sensor Type
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*3 Front Exhaust Pipe Assembly (TWC: Rear Catalyst) *4 Air Fuel Ratio Sensor (Sensor 2)
*5 Tail Exhaust Pipe Assembly - -


A384804C06
1.167,0.802 1.5,0.302 1.5,0.302 1.667,0.302 true 1.083,1.698 1.417,1.198 1.417,1.198 1.583,1.198 true 2.917,3.406 3.25,2.906 3.25,2.906 3.417,2.906 true 0.833,3.583 1.167,3.083 1.167,3.083 1.333,3.083 true 1.271,4.802 1.604,5.302 1.604,5.302 1.771,5.302 true 5.417,3.063 5.75,3.563 5.75,3.563 5.917,3.563 true 0.094,0.083 0.469,0.365 0.375,0.281 12 false *A 1.74,0.198 2.052,0.354 0.313,0.156 10 false *1 1.656,1.094 1.969,1.25 0.313,0.156 10 false *2 1.417,2.979 1.729,3.135 0.313,0.156 10 false *3 1.823,5.219 2.406,5.396 0.583,0.177 10 false *4(*B) 3.49,2.802 3.802,2.958 0.313,0.156 10 false *5 5.99,3.469 6.302,3.625 0.313,0.156 10 false *6
*A for AWD *B for Rear Air Fuel Ratio Sensor Type
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*3 Front Exhaust Pipe Assembly *4 Air Fuel Ratio Sensor (Sensor 2)
*5 Center Exhaust Pipe Sub-assembly (TWC: Rear Catalyst) *6 Tail Exhaust Pipe Assembly



w/o Differential Pressure Sensor (for Rear Heated Oxygen Sensor Type)


A384803C04
1.385,1.125 1.719,0.708 1.719,0.708 1.885,0.708 true 1.26,2.073 1.594,1.656 1.594,1.656 1.76,1.656 true 2.406,3.344 2.708,2.938 2.708,2.938 2.875,2.938 true 1.563,4.583 1.896,5 1.896,5 2.063,5 true 4.865,2.854 5.198,3.271 5.198,3.271 5.365,3.271 true 0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 1.979,0.604 2.292,0.76 0.313,0.156 10 false *1 1.833,1.552 2.146,1.708 0.313,0.156 10 false *2 2.948,2.833 3.26,2.99 0.313,0.156 10 false *3 2.104,4.917 2.729,5.146 0.625,0.229 10 false *4(*B) 5.438,3.167 5.75,3.323 0.313,0.156 10 false *5
*A for 2WD *B for Rear Heated Oxygen Sensor Type
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*3 Front Exhaust Pipe Assembly (TWC: Rear Catalyst) *4 Heated Oxygen Sensor
*5 Tail Exhaust Pipe Assembly - -


A384804C07
1.167,0.802 1.5,0.302 1.5,0.302 1.667,0.302 true 1.083,1.698 1.417,1.198 1.417,1.198 1.583,1.198 true 2.917,3.406 3.25,2.906 3.25,2.906 3.417,2.906 true 0.833,3.583 1.167,3.083 1.167,3.083 1.333,3.083 true 1.271,4.802 1.604,5.302 1.604,5.302 1.771,5.302 true 5.417,3.063 5.75,3.563 5.75,3.563 5.917,3.563 true 0.094,0.083 0.469,0.365 0.375,0.281 12 false *A 1.74,0.198 2.052,0.354 0.313,0.156 10 false *1 1.656,1.094 1.969,1.25 0.313,0.156 10 false *2 1.417,2.979 1.729,3.135 0.313,0.156 10 false *3 1.813,5.219 2.479,5.417 0.667,0.198 10 false *4(*B) 3.49,2.802 3.802,2.958 0.313,0.156 10 false *5 5.99,3.469 6.302,3.625 0.313,0.156 10 false *6
*A for AWD *B for Rear Heated Oxygen Sensor Type
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*3 Front Exhaust Pipe Assembly *4 Heated Oxygen Sensor
*5 Center Exhaust Pipe Sub-assembly (TWC: Rear Catalyst) *6 Tail Exhaust Pipe Assembly



NOTICE:
w/ Differential Pressure Sensor

Replace the exhaust manifold converter sub-assembly (*2) and the front exhaust pipe assembly (*3) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor (sensor 1)*1 and air fuel ratio sensor (sensor 2)*4)


w/o Differential Pressure Sensor (for Rear Air Fuel Ratio Sensor Type)

Replace the exhaust manifold converter sub-assembly (*2) and the front exhaust pipe assembly (*3) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor (sensor 1)*1 and air fuel ratio sensor (sensor 2)*4)


w/o Differential Pressure Sensor (for Rear Heated Oxygen Sensor Type)

Replace the exhaust manifold converter sub-assembly (*2) and the front exhaust pipe assembly (*3) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor (sensor 1)*1 and heated oxygen sensor*4)



MONITOR STRATEGY

w/ Differential Pressure Sensor
Required Sensors/Components (Main) Air fuel ratio sensor (sensor 1)
Air fuel ratio sensor (sensor 2)
Required Sensors/Components (Related) Intake air temperature (mass air flow meter)
Mass air flow meter
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

w/o Differential Pressure Sensor (for Rear Air Fuel Ratio Sensor Type)
Required Sensors/Components (Main) Air fuel ratio sensor (sensor 1)
Air fuel ratio sensor (sensor 2)
Required Sensors/Components (Related) Intake air temperature (mass air flow meter)
Mass air flow meter
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

w/o Differential Pressure Sensor (for Rear Heated Oxygen Sensor Type)
Required Sensors/Components (Main) Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor (mass air flow meter)
Mass air flow meter
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

w/ Differential Pressure Sensor
Response rate during fuel cut from rich condition Completed
Battery voltage 11 V or higher
Intake air temperature (mass air flow meter sub-assembly) -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Sub feedback control Executing
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 140%
All of the following conditions are met 1, 2 and 3
1. Mass air flow 6.0 gm/sec or more, and less than 40 gm/sec
2. Front catalyst temperature (estimated) 570°C (1058°F) or higher, and less than 800°C (1472°F)
3. Rear catalyst temperature (estimated) 460°C (860°F) or higher, and less than 700°C (1292°F)

w/o Differential Pressure Sensor (for Rear Air Fuel Ratio Sensor Type)
Response rate during fuel cut from rich condition Completed
Battery voltage 11 V or higher
Intake air temperature (mass air flow meter sub-assembly) -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Sub feedback control Executing
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 140%
All of the following conditions are met 1, 2 and 3
1. Mass air flow 6.0 gm/sec or more, and less than 40 gm/sec
2. Front catalyst temperature (estimated) 570°C (1058°F) or higher, and less than 800°C (1472°F)
3. Rear catalyst temperature (estimated) 460°C (860°F) or higher, and less than 700°C (1292°F)

w/o Differential Pressure Sensor (for Rear Heated Oxygen Sensor Type)
Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11.02 psi(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 140%
All of the following conditions are met -
Mass air flow rate 6.0 to 40 gm/sec.
Front catalyst temperature (estimated) 570°C (1058°F) to 800°C (1472°F)
Rear catalyst temperature (estimated) 460°C (860°F) to 700°C (1292°F)

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A392182E02
1.313,0.854 1.76,0.333 1.76,0.333 1.906,0.333 false 3.156,3.177 3.594,3.417 0.438,0.24 10 false [C] 5.01,3.177 5.448,3.417 0.438,0.24 10 false [F] 6.771,3.167 7.115,3.49 0.344,0.323 10 false [H] 3.479,2.083 3.823,2.406 0.344,0.323 10 false [D] 1.656,2.083 2,2.406 0.344,0.323 10 false [A] 2.583,1.01 2.927,1.333 0.344,0.323 10 false [B]* 4.375,1.01 4.719,1.333 0.344,0.323 10 false [E]* 6.167,0.635 6.51,0.958 0.344,0.323 10 false [G]* 0.167,1.135 1.635,1.698 1.469,0.563 10 false 60 km/h (37 mph) 0.927,2.219 2.396,2.781 1.469,0.563 10 false Idling 0.188,2.51 1.656,3.073 1.469,0.563 10 false Ignition Switch off 1.406,2.781 2.875,3 1.469,0.219 10 false Warming up 2.354,2.792 3.052,3.406 0.698,0.615 10 false 10 minutes or more 3.323,2.792 3.906,3.396 0.583,0.604 10 false Warming up 4.125,2.792 4.844,3.406 0.719,0.615 10 false 10 minutes or more 5.865,2.802 6.76,3.354 0.896,0.552 10 false 10 minutes or more 0.104,3.448 4.719,3.792 4.615,0.344 10 false *: Drive the vehicle while keeping the engine load as constant as possible 1.99,0.24 4.844,0.635 2.854,0.396 10 false Between 75 and 100 km/h (46 and 62 mph)

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

9.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


10.

Turn the ignition switch off and wait for at least 30 seconds [C].

11.

Turn the ignition switch to ON.

12.

Turn the GTS on.

13.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

14.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


15.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P042000.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.



20.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


21.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

22.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



23.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

24.

Input the DTC: P042000.

25.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CONDITIONING FOR SENSOR TESTING

for Rear Heated Oxygen Sensor Type:

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A270243E20
4.885,3.094 4.885,3.313 false 4.885,3.313 5.24,3.313 false 5.177,3.094 5.177,3.313 false 3.615,0.875 3.844,1.073 0.229,0.198 10 false (c) 0.615,0.563 1.698,0.76 1.083,0.198 10 false Engine Speed 0.813,0.979 1.615,1.177 0.802,0.198 10 false 3000 rpm 0.813,1.51 1.615,1.708 0.802,0.198 10 false 2000 rpm 1.115,2.531 1.563,2.729 0.448,0.198 10 false Idling 0.354,2.76 1.531,2.958 1.177,0.198 10 false Ignition Switch off 1.656,2.656 2.302,2.854 0.646,0.198 10 false (a) 2.073,2.385 2.302,2.583 0.229,0.198 10 false (b) 4.792,0.875 5.021,1.073 0.229,0.198 10 false (e) 5.094,1.406 5.323,1.604 0.229,0.198 10 false (d) 2.104,3.125 3.021,3.323 0.917,0.198 10 false Warming up 3.365,3.125 4.542,3.323 1.177,0.198 10 false At least 3 minutes 5.292,3.24 6.104,3.438 0.813,0.198 10 false 2 seconds 4.854,3.344 5.323,3.563 0.469,0.219 10 false Check 6.635,2.76 7.031,2.958 0.396,0.198 10 false Time 4.375,0.885 4.604,1.083 0.229,0.198 10 false (d)

(a) Connect the GTS to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Enter the following menus: Powertrain / Engine / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

(d) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(e) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS.


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the GTS.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A201081E21
0.104,0.135 4.417,0.375 4.313,0.24 10 false Voltage Output When Active Air Fuel Ratio Control Not Performed: 2.719,0.74 3.76,0.948 1.042,0.208 10 false Normal Catalyst 5.083,0.74 6.573,0.969 1.49,0.229 10 false Deteriorated Catalyst 2.833,3.26 3.646,3.448 0.813,0.188 10 false 10 seconds 5.406,3.271 6.198,3.5 0.792,0.229 10 false 10 seconds 1.667,1.083 2.042,1.24 0.375,0.156 10 false 3.4 V 1.667,1.427 2.042,1.604 0.375,0.177 10 false 3.1 V 1.667,2.365 2.042,2.542 0.375,0.177 10 false 1.0 V 1.76,3.052 2.031,3.229 0.271,0.177 10 false 0 V 0.135,1.25 1.5,1.958 1.365,0.708 10 false Waveform of Air Fuel Ratio Sensor in Front of Three-Way Catalytic Converter 0.177,2.49 1.448,3.229 1.271,0.74 10 false Waveform of Heated Oxygen Sensor Behind Three-Way Catalytic Converter


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P042000, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P017100 (System Too Lean) and P017200 (System Too Rich).

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P042000 is output (w/ Differential pressure sensor) A
DTC P042000 is output (w/o Differential Pressure Sensor (for Rear Air Fuel Ratio Sensor Type)) B
DTC P042000 is output (w/o Differential Pressure Sensor (for Rear Heated Oxygen Sensor Type)) C
DTC P042000 and other DTCs are output D


HINT:

If any DTCs other than P042000 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

16.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


e.

Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.


f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B1S2
50004 372 8 230,564

g.

Change the fuel injection volume using the GTS, and monitor the output current of the air fuel ratio sensor (sensor 1) (A/F (O2) Sensor Current B1S1 and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S2 displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The air fuel ratio sensor (sensor 1) is displayed as A/F (O2) Sensor Current B1S1 and the air fuel ratio sensor (sensor 2) is displayed as A/F (O2) Sensor Current B1S2 on the GTS.

·

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean More than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean More than 0.33 mA


Result:
Status of A/F (O2) Sensor Current B1S1 Status of A/F (O2) Sensor Current B1S2 Actual air fuel ratio, air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) condition Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


B
Rich Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


Lean/Rich Lean Air fuel ratio sensor (sensor 2) malfunction
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


C
Lean/Rich Rich Air fuel ratio sensor (sensor 2) malfunction
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system




Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1 is consistently more than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2 is consistently more than 0.33 mA.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1 is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2 is consistently below -0.86 mA.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.

HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B1S2.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST





A

3.CHECK FOR EXHAUST GAS LEAK

B

4.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1) (SENSOR 1)

C

5.CHECK FOR EXHAUST GAS LEAK

D

7.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.


OK:

No gas leaks.


Result:
Proceed to
OK
NG



OK

15.CHECK DTC OUTPUT (DTC P042000)

NG

9.REPAIR OR REPLACE EXHAUST SYSTEM
4.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1) (SENSOR 1)
a.

Replace the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.


OK:

No gas leaks in exhaust system.


Result:
Proceed to
OK
NG



OK

6.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

NG

9.REPAIR OR REPLACE EXHAUST SYSTEM
6.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)
a.

Replace the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.


OK:

No gas leaks in exhaust system.


Result:
Proceed to
OK
NG



OK

8.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

9.REPAIR OR REPLACE EXHAUST SYSTEM
8.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P017100, P017200 Inspection Procedure.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P017100


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
9.REPAIR OR REPLACE EXHAUST SYSTEM
a.

Repair or replace exhaust system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC P042000 is output B



A

12.CHECK MODEL

B

15.CHECK DTC OUTPUT (DTC P042000)
12.CHECK MODEL
a.

Choose the model to be inspection.


Result:
Result Proceed to
for 2WD A
for AWD B



A

13.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

B

14.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
13.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>MONOLITHIC CONVERTER>COMPONENTS


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for 2WD)>COMPONENTS


Result:
Proceed to
NEXT



NEXT

END

14.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the center exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>MONOLITHIC CONVERTER>COMPONENTS


b.

Replace the center exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for AWD)>COMPONENTS


Result:
Proceed to
NEXT



NEXT

END

15.CHECK DTC OUTPUT (DTC P042000)
NOTICE:

IF DTC P042000 is output, replace the converter assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.


Result:
Result Proceed to
DTC P042000 is output A
DTC P042000 and P043000 are output B


HINT:

Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly (w/ Differential pressure sensor).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

REPLACE CONVERTER ASSEMBLY RH (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

B

REPLACE CONVERTER ASSEMBLY RH AND LH (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

16.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 225,218

f.

Perform the Active Test with the engine idling (change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status of A/F (O2) Sensor Voltage B1S1 Status of O2 Sensor Voltage B1S2 Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


B
Rich Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


Lean/Rich Lean Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system




Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the A/F (O2) Sensor Voltage B1S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.




A

17.CHECK FOR EXHAUST GAS LEAK

B

18.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

C

19.CHECK FOR EXHAUST GAS LEAK

D

21.CHECK FOR EXHAUST GAS LEAK
17.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

25.CHECK MODEL

NG

23.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
18.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
a.

Replace the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click here



Result:
Proceed to
NEXT



NEXT

24.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
19.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

20.REPLACE HEATED OXYGEN SENSOR

NG

23.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
20.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

24.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
21.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

22.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

23.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
22.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P017100 Inspection Procedure.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P017100


Result:
Proceed to
NEXT



NEXT

24.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
23.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace the exhaust gas leak point.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

24.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
24.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

k.

Read the DTCs.

Result:
Result Proceed to
DTC P042000 is output A
DTCs are not output
(No pending DTCs output)
B




A

25.CHECK MODEL

B

END

25.CHECK MODEL
a.

Choose the model to be inspection.


Result:
Result Proceed to
for 2WD A
for AWD B



A

26.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

B

27.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
26.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for 2WD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

END

27.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the center exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


b.

Replace the center exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for AWD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

END