Home › Audio / Visual / Telematics › TELEMATICS › TELEPHONE ANTENNA CORD › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060052 TELEMATICS _0294135 TELEPHONE ANTENNA CORD A

TELEMATICS  TELEPHONE ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101D 1.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.
E396317C01
0.417,2.25 1.583,3.333 1.167,1.083 2,2.25 3.167,3.333 1.167,1.083 2.125,0.906 2.375,0.75 true 0.719,1.385 1.115,1.521 true 0.458,2.26 0.833,2.5 0.375,0.24 12 false *A 2.042,2.26 2.417,2.5 0.375,0.24 12 false *B 2.375,0.646 2.583,0.854 0.208,0.208 10 true *a 0.51,1.26 0.719,1.469 0.208,0.208 10 true *b
*A for Type A
*B for Type B
*a Guide
*b Clamp


Engage the clamp and guide to temporarily install the No. 3 antenna cord sub-assembly.


b.

Install the bolt.

Torque:
for Type A : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the connector of the floor wire.


d.
E353809

Engage the clamps install the No. 3 antenna cord sub-assembly.


e.

Connect the connector.


f.

for Glass Antenna Type:

i.

Connect the connector of the No. 4 antenna cord sub-assembly.



Hide 86101J 2.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

for Type A:

i.

Remove the old double-sided tape from the roof headlining.

E353816C01
4.24,1.104 4.448,1.448 true 4.51,1.438 4.74,1.625 0.229,0.188 10 true *a
*a Marking - -
V100144

Double-sided Tape
V100136

Front



ii.

Prepare an appropriate amount of new double-sided tape.

HINT:

Be careful not to touch the adhesive surface.



iii.

Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining.


iv.

Peel off the release paper from the double-sided tape.


v.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.

E359077C04
1.833,1.333 2.344,1.031 true 2.656,1.031 3.333,0.667 true 4.083,1.25 4.948,1.427 true 5.885,2.396 6.5,2.583 true 6.354,1 6.833,1.667 true 6.583,1.083 6.969,0.917 true 6.448,0.938 6.917,0.25 true 3.375,0.51 3.594,0.719 0.219,0.208 10 false *a 6.844,1.677 7.073,1.885 0.229,0.208 10 false *b 6.979,0.781 7.156,0.99 0.177,0.208 10 false *c 3.875,1.125 4.104,1.344 0.229,0.219 10 false *d 1.646,1.271 1.875,1.469 0.229,0.198 10 false *e 6.948,0.104 7.115,0.292 0.167,0.188 10 false *f 6.531,2.479 6.74,2.698 0.208,0.219 10 false *g
*a Marking Tape (A) *b Marking Tape (B)
*c Adhesive Tape (A) *d Adhesive Tape (B)
*e Protrusion *f Edge of the roof headlining
*g Adjustment Area - -
V100136

Front - -



vi.

Install the No. 2 antenna cord sub-assembly on the double-sided tape of the roof headlining.

NOTICE:
·

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




vii.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the edge of roof headlining on the roof headlining and secure the No. 2 antenna cord sub-assembly with the adhesive tape (A) as shown in the illustration.

NOTICE:

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.



viii.

Apply the adhesive tape (B) as shown in the illustration to secure the No. 2 antenna cord subassembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




b.

for Type B:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.

E353818C07
2.635,1.052 3.333,0.667 true 6.792,1.688 6.354,1.031 true 6.604,1.125 6.958,1.063 true 6.938,0.219 6.479,0.948 true 4.927,1.458 4.083,1.25 true 6.5,2.667 5.875,2.417 true 4.5,2.75 3.854,2.292 true 4.5,2.75 4.24,2.302 true 4.5,2.75 4.604,2.313 true 4.5,2.75 5.094,2.365 true 4.5,2.75 5.583,2.292 true 1.833,1.333 2.344,1.042 true 2.292,2.104 3,2.75 true 2.656,2.146 3,2.75 true 2.896,2.26 3,2.75 true 3.125,2.292 3,2.75 true 3,2.75 3.469,2.25 true 3.365,0.521 3.563,0.719 0.198,0.198 10 false *a 6.813,1.708 7.021,1.906 0.208,0.198 10 false *b 6.979,0.958 7.156,1.156 0.177,0.198 10 false *c 6.948,0.083 7.156,0.302 0.208,0.219 10 false *f 3.885,1.135 4.083,1.333 0.198,0.198 10 false *d 6.552,2.594 6.729,2.781 0.177,0.188 10 false *g 4.396,2.76 4.604,2.958 0.208,0.198 10 true *d 1.667,1.281 1.865,1.479 0.198,0.198 10 false *e 2.906,2.76 3.115,2.958 0.208,0.198 10 true *d
*a Marking Tape (A) *b Marking Tape (B)
*c Adhesive Tape (A) *d Adhesive Tape (B)
*e Marking (A) *f Protrusion
*g Edge of the roof headlining - -
V100136

Front - -



ii.

Install the No. 2 antenna cord sub-assembly on the butyl tape of the roof headlining.

NOTICE:
·

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




iii.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the edge of roof headlining on the roof headlining and secure the No. 2 antenna cord sub-assembly with the adhesive tape (A) as shown in the illustration.

NOTICE:

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.



iv.

Apply the 11 adhesive tapes (B) as shown in the illustration to secure the No. 2 antenna cord subassembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




Hide 86101 4.INSTALL ANTENNA CORD SUB-ASSEMBLY

a.

Connect the connector.


b.

Engage the clamps to install the antenna cord sub-assembly.

E353801


Hide 55086 5.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55401E 6.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY