Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060052 TELEMATICS _0298115 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1571  Green LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON.

If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.

If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1571 Green LED Error Current for the manual (SOS) switch indicator (green) exceeds malfunction threshold for 10 seconds when the ignition switch is ON.
·

Telematics transceiver

·

Map light assembly

·

Mayday switch assembly (manual (SOS) switch)

·

Wire harness or connector



WIRING DIAGRAM

E359943E02
5.438,1.958 5.896,2.156 0.458,0.198 10 false F51 5.417,2.135 6.906,2.417 1.49,0.281 10 false Telematics Transceiver 5.792,1.021 6.406,1.219 0.615,0.198 10 false IND2 5.781,1.344 6.396,1.542 0.615,0.198 10 false SIG- 5.5,0.875 5.813,1.073 0.313,0.198 10 false 12 5.531,1.333 5.844,1.531 0.313,0.198 10 false 26 3.385,0.896 4,1.094 0.615,0.198 10 false IND2 2.531,0.917 3.146,1.115 0.615,0.198 10 false IND2 3.302,1.344 3.917,1.542 0.615,0.198 10 false GND3 2.5,1.354 3.115,1.552 0.615,0.198 10 false GND 3.792,0.906 3.948,1.104 0.156,0.198 10 false 5 3.792,1.323 3.948,1.521 0.156,0.198 10 false 1 0.51,2.958 0.823,3.156 0.313,0.198 10 false R4 0.51,3.115 3.26,3.313 2.75,0.198 10 false Map Light Assembly 0.76,1.99 2.396,2.344 1.635,0.354 10 false Mayday Switch Assembly (Manual (SOS) Switch) 1.323,1.25 2.052,1.469 0.729,0.219 10 false GREEN

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH INPUT VOLTAGE)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH INPUT VOLTAGE)
a.
E359858C02
0.094,0.896 0.51,1.188 0.417,0.292 1.552,1.323 1.177,1.958 true 2.76,1.979 2.385,1.375 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.219,0.938 0.531,1.135 0.313,0.198 10 false R4 0.854,1.906 1.469,2.104 0.615,0.198 10 false IND2 2.813,1.917 3.427,2.115 0.615,0.198 10 false GND3
*a Component with harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R4-5 (IND2) - R4-1 (GND3) 2 seconds after ignition switch turned to ON → Ignition switch off 2 to 5 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAYDAY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)
3.INSPECT MAYDAY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)
a.

Remove the mayday switch assembly (manual (SOS) switch).

Click hereAudio / Visual / Telematics>TELEMATICS>MAYDAY SWITCH>REMOVAL


b.

Inspect the mayday switch assembly (manual (SOS) switch).

Click hereAudio / Visual / Telematics>TELEMATICS>MAYDAY SWITCH>INSPECTION


Result:
Result Proceed to
OK (for TMMT Made) A
OK (for TMC Made) B
NG C



A

B

C

REPLACE MAYDAY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH)

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)
a.

Disconnect the F51 telematics transceiver connector.


b.

Disconnect the R4 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-12 (IND2) - R4-5 (IND2) Always Below 1 Ω
F51-12 (IND2) or R4-5 (IND2) - Body ground Always 10 kΩ or higher
F51-26 (SIG-) - R4-1 (GND3) Always Below 1 Ω
F51-26 (SIG-) or R4-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT