Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › from 2020.08
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0295314 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cooler condenser assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))

Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))

Hide 3.REMOVE HEADLIGHT ASSEMBLY LH (for Single Beam Headlight)

Hide 4.REMOVE HEADLIGHT ASSEMBLY RH (for Single Beam Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 5.REMOVE HEADLIGHT ASSEMBLY LH (for Triple Beam Headlight)

Hide 6.REMOVE HEADLIGHT ASSEMBLY RH (for Triple Beam Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 17751 7.REMOVE NO. 1 AIR CLEANER INLET (for 8NR-FTS)

Hide 17751 8.REMOVE NO. 1 AIR CLEANER INLET (for 3ZR-FAE)

Hide 52029A 9.REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY (for 8NR-FTS)

Hide 52029A 10.REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY (for 3ZR-FAE)

Hide 53117C 11.REMOVE NO. 1 RADIATOR GRILLE RETAINER

Hide 16561C 12.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL

Hide 53510 14.REMOVE HOOD LOCK ASSEMBLY

Hide 53205 15.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 8NR-FTS)

Hide 53205 16.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 3ZR-FAE)

Hide 16594 17.REMOVE NO. 2 RADIATOR AIR GUIDE (for 8NR-FTS)

Hide 16594 18.REMOVE NO. 2 RADIATOR AIR GUIDE (for 3ZR-FAE)

Hide 52611 19.REMOVE FRONT BUMPER ENERGY ABSORBER

Hide 52131A 20.REMOVE FRONT BUMPER REINFORCEMENT

Hide 16595B 21.REMOVE NO. 1 RADIATOR AIR GUIDE LH

Hide 16593B 22.REMOVE NO. 1 RADIATOR AIR GUIDE RH

Hide 88703 23.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.
I112407

Remove the bolt to disconnect the discharge hose sub-assembly from the cooler condenser assembly.


b.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 24.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (for VALEO Made)

a.
I112406

Remove the bolt to disconnect the cooler refrigerant liquid pipe A from the cooler condenser assembly.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 25.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (for DENSO Made)

a.

While pressing the end of the cooler refrigerant liquid pipe A into the end of the cooler condenser assembly, use pliers to squeeze together both sides of the piping clamp until it breaks apart.

E336869C02
3.125,3.042 3.75,3.365 3.75,3.365 3.24,2.792 true 4.625,2.688 4.625,2.104 false 5.865,2.688 5.865,2.271 false 4.573,2.75 4.885,2.906 0.313,0.156 10 false *1 5.813,2.74 6.125,2.896 0.313,0.156 10 false *2 3.781,3.302 3.979,3.448 0.198,0.146 10 true *3 4.646,0.813 4.958,0.969 0.313,0.156 10 false *a
*1 Cooler Refrigerant Liquid Pipe A *2 Cooler Condenser Assembly
*3 Piping Clamp - -
*a Press In - -


NOTICE:
·

If any foreign matter is adhered to the connecting part, brush it off or use compressed air to remove it.

·

Make sure that fragments of the piping clamp do not enter the piping.




b.

Disconnect the cooler refrigerant liquid pipe A.

NOTICE:

Clean off any foreign matter near the ends of the cooler refrigerant liquid pipe A and cooler condenser assembly.



c.

Remove the 2 O-rings from the cooler refrigerant liquid pipe A.

NOTICE:

Wrap the open ends of the separated cooler condenser assembly and cooler refrigerant liquid pipe A with vinyl tape to prevent entry of moisture and foreign matter.



d.

Remove the piping clamp.


Hide 88460 26.REMOVE COOLER CONDENSER ASSEMBLY

a.
I112408C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guides to remove the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.