Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT EVAPORATOR TEMPERATURE SENSOR (for VALEO Made) › from 2020.08
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0295317 FRONT EVAPORATOR TEMPERATURE SENSOR(for VALEO Made) A

HEATING / AIR CONDITIONING  FRONT EVAPORATOR TEMPERATURE SENSOR(for VALEO Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 1 cooler thermistor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Front Passenger Side Upper Air Mix)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Driver Side Upper Air Mix)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Driver Side Lower Air Mix)

·

No. 2 Air Conditioning Radiator Damper Servo Sub-assembly (Mode Switching)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Front Passenger Side Lower Air Mix)

·

Air conditioning amplifier assembly


AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)
·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Upper Air Mix)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Lower Air Mix)

·

No. 2 Air Conditioning Radiator Damper Servo Sub-assembly (Mode Switching)

·

Air conditioning amplifier assembly


Initialize servo motor (Air conditioning system) DTCs are stored for Automatic Air Conditioning System:(Click here)
for Manual Air Conditioning System:(Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 87114L 3.REMOVE NO. 2 HEATER COVER (w/ PTC Heater)

Hide 87710G 4.REMOVE QUICK HEATER ASSEMBLY (w/ PTC Heater)

Hide 88650N 5.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 87050C 7.REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

Hide 87050C 8.REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 87050D 9.REMOVE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

Hide 87107A 12.REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY

Hide 88501 16.REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 88625 17.REMOVE NO. 1 COOLER THERMISTOR

a.
I112417

Remove the No. 1 cooler thermistor.