77020A
1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Install a new fuel suction tube set gasket to the fuel tank assembly.
Connect the fuel return vent tube sub-assembly to the fuel suction tube with pump and gauge assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
| *1 | Fuel Return Vent Tube Sub-assembly |
|
Front of the Vehicle |
Make sure to correctly assemble the fuel return vent tube sub-assembly as shown in the illustration. If assembled incorrectly, the fuel sender gauge assembly (No. 2 fuel sender gauge assembly) may catch on the fuel return vent tube resulting in incorrect operation of the fuel sender gauge assembly (No. 2 fuel sender gauge assembly) and an incorrect value being displayed on the fuel gauge.
When connecting the fuel tube connector, do not excessively pull on the fuel return vent tube sub-assembly.
Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
| *a | Protrusion |
|
Notch |
Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.
77144
2.INSTALL FUEL PUMP GAUGE RETAINER
Install the fuel pump gauge retainer.
While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.
| *a | Insertion Point |
| *b | SST (Plate) |
| *c | SST (Claw) |
| *d | SST (Bolt) |
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
| *a | Triangle Mark (Fuel Pump Gauge Retainer) |
| *b | Triangle Mark (Fuel Tank Assembly) |
| *c | SST (Handle) |
| *d | SST (Plate) |
| *e | SST (Claw) |
| *f | SST (Bolt) |
|
Front Side of Vehicle |
Install SST (handle) to SST (plate).
Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer are aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.
Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
Make sure that the fuel suction tube set gasket does not come off.
Engage the claw to install the No. 1 fuel tube clamp.
77754B
3.CONNECT CHARCOAL CANISTER OUTLET HOSE
| *a | 180° |
| *b | Top of Vehicle |
Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.
Engage the clip within the area shown in the illustration.
77026A
4.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.
77209F
5.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.
| *1 | Fuel Suction Plate Sub-assembly | *2 | Tube Joint Clip |
| *3 | Fuel Tank Main Tube Sub-assembly | - | - |
| *a | Fuel Tube Joint | *b | O-ring |
| *c | Correct | *d | Incorrect |
| *e | Collar | - | - |
|
Insert |
|
Insert |
Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.
Check that the fuel tube joint is securely inserted to the end.
Check that the tube joint clip is on the collar of the fuel tube joint.
After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.
6.CONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY
Connect the fuel tank evaporation vent tube sub-assembly to the fuel suction tube with pump and gauge assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
58325E
7.INSTALL REAR FLOOR SERVICE HOLE COVER LH
Remove any remaining butyl tape from the rear floor service hole cover LH and vehicle body.
Clean the installation surfaces of the rear floor service hole cover LH and vehicle body.
Connect the fuel suction tube with pump and gauge assembly connector.
Install the rear floor service hole cover LH with new butyl tape.
8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic leaning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
10.INSPECT FOR FUEL LEAK
11.INSTALL REAR SEAT ASSEMBLY
12.PERFORM INITIALIZATION
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION