Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
1. PRECAUTION
Keep fuel away from rubber or leather parts.
If a malfunction such as pump lock occurs and the fuel pump is damaged, excessive current may be continuously applied to the fuel pump control ECU, damaging its internal parts. Make sure to replace the fuel pump control ECU at the same time when replacing the fuel pump.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
Check fuel pump operation.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
3.CHECK FUEL PRESSURE
Discharge fuel system pressure.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
Measure the battery voltage.
11 to 14 V
Disconnect the cable from the negative (-) battery terminal.
Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Remove the windshield wiper motor and link assembly.
Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL
Remove the No. 1 heater air duct splash shield seal.
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL
Remove the water guard plate LH(for TMC Made RHD).
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL
Remove the cowl body mounting reinforcement LH.
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL
Remove the cowl body mounting reinforcement RH.
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL
Remove the outer cowl top panel sub-assembly (for LHD).
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL
Remove the outer cowl top panel sub-assembly (for RHD).
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL
Remove the radiator cover.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL
Remove the No. 1 air cleaner inlet.
Click hereEngine / Hybrid System>8NR-FTS (COOLING)>RADIATOR>REMOVAL
Remove the air cleaner cap with air cleaner hose.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
Disconnect the fuel tube sub-assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for High Pressure)>REMOVAL
| *1 | Fuel Tube Sub-assembly (Vehicle Side) |
| *a | SST (Hose Band) |
| *b | SST (T-joint) |
| *c | SST (Gauge) |
| *d | SST (Hose Joint) |
| *e | SST (Hose) |
| *f | SST (Fuel Tube Connector) |
| *g | Fuel Pipe (Vehicle Side) |
Install SST (EFI fuel pressure gauge) as shown in the illustration.
Wipe up any spilled fuel.
Connect the cable to the negative (-) battery terminal.
Initialization after reconnecting auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
Measure the fuel pressure.
196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)
If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump, fuel filter and fuel pressure regulator assembly.
If the result is not as specified, replace the fuel pressure regulator assembly.
Disconnect the GTS from the DLC3.
Start the engine.
Measure the fuel pressure at idle.
196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)
Refer to Standard Idle Speed.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
Stop the engine.
Check that the fuel pressure remains as specified for 5 minutes.
147 kPa (1.5 kgf/cm2, 21 psi) or more
If the result is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.
After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent fuel from spraying.
Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the fuel tube sub-assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for High Pressure)>INSTALLATION
Install the air cleaner cap with air cleaner hose.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
Install the No. 1 air cleaner inlet.
Click hereEngine / Hybrid System>8NR-FTS (COOLING)>RADIATOR>INSTALLATION
Install the radiator cover.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION
Install the outer cowl top panel sub-assembly (for LHD).
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION
Install the outer cowl top panel sub-assembly (for RHD).
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION
Install the cowl body mounting reinforcement RH.
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION
Install the cowl body mounting reinforcement LH.
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION
Install the water guard plate LH(for TMC Made RHD).
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION
Install theNo. 1 heater air duct splash shield seal.
Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION
Install the windshield wiper motor assembly.
Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION
Inspect for fuel leaks.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
4.CHECK FUEL PRESSURE (for High Pressure)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start and warm up the engine.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).
| Tester Display |
|---|
| Fuel Pressure (High) |
Check the high pressure side fuel pressure.
4000 to 18000 kPa (40.8 to 183.5 kgf/cm2, 580 to 2610 psi)
If the result is not as specified, check the fuel pump, fuel pump assembly, fuel pressure sensor and wire harnesses.
Stop the engine.