Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.08
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299016 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Improper Operation  


DESCRIPTION

When the theft deterrent system operates by itself, it could be due to something such as a short circuit in the courtesy light switch of any of the doors or the hood causing a signal to be sent in error.

HINT:

Preconditions for Arming Preparation:

·

The ignition switch is off and all the doors and the hood are closed and all doors are locked by wireless operation or entry operation*1.

*1: w/ Entry and Start System




CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The theft deterrent system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the theft deterrent system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.

·

The function "Read operation history" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.



PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CONFIRMATION
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in the problem analysis:

What? Vehicle model, system name
When? Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where? Whether the problem occurs at a specific location
Under what conditions? Whether the doors were locked or unlocked, whether the engine switch was on, whether the engine was running
How did it happen? Problem symptoms*

-

*: Be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem, and then check for DTCs.




Result:
Proceed to
NEXT



NEXT

2.CHECK THEFT DETERRENT SYSTEM OPERATION HISTORY
2.CHECK THEFT DETERRENT SYSTEM OPERATION HISTORY
a.

Use the GTS to check the theft deterrent system operation history around the time that the malfunction reported by the customer occurred, based on the contents of the customer interview and the last recorded theft deterrent system operation history around the time that the problem is reported to have occurred.

i.

On the GTS screen, enter the following menus: Body / Main Body / Utility / Operation History Analysis. According to the display on the GTS, read the operation history.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>OPERATION HISTORY LIST


ii.

Check that there is theft deterrent system operation history as reported by the customer.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>OPERATION HISTORY LIST

HINT:

Based on the displayed operation history, perform vehicle-side inspection, and perform repairs if a problem is found. If the vehicle has no malfunction, interview the customer about possible causes such as "the driver" and "environmental / other than the driver".




Result:
Result Proceed to
There is operational history around the time that the customer reported the malfunction to have occurred, but the malfunction could not be identified even by following the instructions to inspect the relevant areas A
There is operational history around the time that the customer reported the malfunction to have occurred, and by following the instructions to inspect the relevant areas, the malfunction was identified B
There is no operational history around the time that the customer reported the malfunction to have occurred. C



A

3.CHECK SECURITY INDICATOR LIGHT OPERATION

B

12.INTERVIEW THE CUSTOMER

C

END

3.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the theft deterrent system is in arming preparation state, check that the security indicator light is illuminated.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION


b.

When the theft deterrent system is in armed state, check that the security indicator light blinks.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

HINT:
State of Theft Deterrent System Contents Security Indicator Light Condition
Disarmed state (1), (2) Theft deterrent system is unset.
·

Off (Immobiliser system unset)

·

Blinking (Immobiliser system set)


Arming preparation state Standby period after theft deterrent system set conditions are met but before theft deterrent system is actually set (approximately 30 seconds).
(Theft detection not performed)
On
Armed state Theft deterrent system is unset.
(Theft detection is possible)
Blinking (Immobiliser system set)
Alarm sounding state Theft attempt is detected, and alarm is sounded using turn signal light, security horn assembly and vehicle horn.
(Alarm sounds for 27.5 seconds)
On



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS

NG

4.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
-
IG SW Ignition switch ON signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off or ACC
-
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS

NG

5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
RL-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52

Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS

NG

6.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch assembly RH signal ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch assembly LH signal ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
FR Door Courtesy SW Front door courtesy light switch assembly RH signal ON or OFF ON: Front door RH open
OFF: Front door RH closed
-
FL Door Courtesy SW Front door courtesy light switch assembly LH signal ON or OFF ON: Front door LH open
OFF: Front door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 24,25,197,199
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS

NG

7.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy light switch ON or OFF ON: Back door open
OFF: Back door closed
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Courtesy SW
50003 123 26
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (HOOD COURTESY SW)

NG

8.READ VALUE USING GTS (HOOD COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy SW Hood courtesy switch ON or OFF ON: Hood open
OFF: Hood closed
-
Body Electrical > Main Body > Data List
Tester Display
Hood Courtesy SW
50003 123 200
OK:

The GTS display changes correctly in response to the hood courtesy switch (hood lock assembly) status.



Result:
Proceed to
OK
NG



OK

9.INTERVIEW THE CUSTOMER

NG

10.INSPECT HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
9.INTERVIEW THE CUSTOMER
a.

If the phenomenon could not be confirmed or reproduced, after explaining this to the customer, also explain the history of input signals from the electrical key transmitter sub-assembly (electronic key) for the relevant date/time in the operation history.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


Standard:

Cause was identified


Result:
Proceed to
OK
NG



OK

END

NG

10.INSPECT HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
a.

Remove the hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL


b.

Inspect the hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

NG

REPLACE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A8 hood courtesy switch (hood lock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-11 (HCTY) - A8-1 (+) Always Below 1 Ω
F15-11 (HCTY) or A8-1 (+) - Body ground Always 10 kΩ or higher
A8-2 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INTERVIEW THE CUSTOMER
a.

If the phenomenon could not be confirmed or reproduced, after explaining this to the customer, also explain the history of input signals from the electrical key transmitter sub-assembly (electronic key) for the relevant date/time in the operation history.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


Standard:

Cause was identified


Result:
Proceed to
OK
NG



OK

END

NG