Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 2 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

ECM



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C360942E08
1.302,0.979 1.719,1.167 0.417,0.188 10 false 120 Ω 5.479,0.99 5.979,1.177 0.5,0.188 10 false 120 Ω 1.979,0.625 2.396,0.813 0.417,0.188 10 false CA4H 1.969,1.146 2.385,1.333 0.417,0.188 10 false CA4L 1.052,1.646 1.469,1.833 0.417,0.188 10 false F74 1.031,1.823 2.542,2.198 1.51,0.375 10 false Central Gateway ECU (Network Gateway ECU) 2.417,0.615 2.833,0.802 0.417,0.188 10 false 18 2.427,1.156 2.844,1.344 0.417,0.188 10 false 17 4.594,0.646 5.01,0.833 0.417,0.188 10 false 13 4.583,1.156 5,1.344 0.417,0.188 10 false 26 5.25,1.646 5.667,1.833 0.417,0.188 10 false A38 5.208,1.833 5.677,2.031 0.469,0.198 10 false ECM 4.823,0.615 5.24,0.802 0.417,0.188 10 false CANH 4.823,1.156 5.24,1.344 0.417,0.188 10 false CANL

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the ECM, refer to Service Bulletin.*1


*1: w/ Entry and Start System



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367277C30
1.417,0.167 1.917,0.417 0.5,0.25 1.333,1.833 1.615,1.219 true 2.167,1.833 1.813,1.219 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.219 1.927,0.417 0.396,0.198 10 false F74 2.167,1.865 2.667,2.031 0.5,0.167 10 false CA4H 1.01,1.844 1.51,2.01 0.5,0.167 10 false CA4L
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F74-17 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

2.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM)
2.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM)
a.

Reconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Disconnect the ECM connector.


c.
C328875C35
1.583,0.083 2.083,0.333 0.5,0.25 2.656,0.885 1.792,1.854 true 2.677,0.99 2.563,1.865 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.719,0.125 2.031,0.281 0.313,0.156 10 false A38 1.594,1.885 2.094,2.042 0.5,0.156 10 false CANH 2.396,1.896 2.802,2.042 0.406,0.146 10 false CANL
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-13 (CANH) - A38-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for 8NR-FTS) A
OK (for 3ZR-FAE) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))