The yaw rate and acceleration sensor is built into the airbag sensor assembly. The airbag sensor assembly sends yaw rate and acceleration sensor signals to each ECU via CAN communication. These signals are used for the neutral control of the CVT system. If a yaw rate and acceleration sensor circuit malfunction signal, yaw rate and acceleration sensor stuck signal or abnormal sensor output signal is received from the skid control ECU, a DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P158549 | Acceleration Sensor Circuit Internal Electronic Failure | Yaw rate and acceleration sensor circuit malfunction signal is received from the skid control ECU for 3 seconds or more (1 trip detection logic). | ·
Airbag sensor assembly (yaw rate and acceleration sensor) ·
CAN communication system ·
Wire harness or connector ·
Brake actuator assembly (skid control ECU) ·
ECM |
Does not come on | DTC stored | SAE Code:
P1585 |
| P158649 | Acceleration Sensor Circuit Range / Performance Internal Electronic Failure | Yaw rate and acceleration sensor stuck signal or abnormal sensor output signal is received from the skid control ECU for 3 seconds or more (1 trip detection logic). | ·
Airbag sensor assembly (yaw rate and acceleration sensor) ·
CAN communication system ·
Wire harness or connector ·
Brake actuator assembly (skid control ECU) ·
ECM |
Does not come on | DTC stored | SAE Code:
P1586 |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle while accelerating and decelerating repeatedly, for several minutes.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P158549 or P158649.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P158504.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P158504
Perform initialization after replacing any parts related to the system.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Check that no DTCs are stored after performing initialization.
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: System Select / Health Check.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P158549 or P158649 is output | A |
| DTC P158549 or P158649 and other DTCs are output | B |
If any CAN communication system DTCs are output, perform troubleshooting for the CAN communication system first.
If any DTCs other than P158549 or P158649 are output, troubleshoot those DTCs first.
A
B
Check the airbag sensor assembly (yaw rate and acceleration sensor) installation condition.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS
The airbag sensor assembly is not tilted and its installation bolts are tightened to the specified torque, the airbag sensor assembly bracket is not deformed and there are no foreign objects under the airbag sensor assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F150 airbag sensor assembly (yaw rate and acceleration sensor) connector.
| *a | Front view of wire harness connector
(to Airbag sensor assembly (Yaw rate and acceleration sensor)) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F150-36 (IG2) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F150-33 (E1) - Body ground | Always | Below 1 Ω |
| F150-32 (E2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the airbag sensor assembly (yaw rate and acceleration sensor).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Reinstall or replace the airbag sensor assembly (yaw rate and acceleration sensor).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Perform the initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P158549 or P158649 is output | A |
| DTCs are not output | B |
A
B
Replace the brake actuator assembly (skid control ECU).
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P158549 or P158649 is output | A |
| DTCs are not output | B |
A
B