Home › Drivetrain › K313 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › from 2020.08
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0299314 TRANSMISSION CONTROL CABLE A

K313 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Gas leaks from exhaust system Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 28800 4.REMOVE BATTERY

Hide 33504F 5.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 6.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 53141F 7.REMOVE RADIATOR COVER

Hide 17751 8.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 9.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17701 10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 57533B 13.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 14.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 58151 15.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C364049

Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body.


Hide 33820B 16.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.

for TMMT Made:

i.
C364051C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the end of the transmission control cable assembly from the floor shift shift lever assembly.


ii.
C364050C01
1.115,1.927 1.448,1.594 true 0.885,1.896 1.073,2.094 0.188,0.198 10 true *1
*1 Slider
V100135

Push
V113147

Remove in this Direction


Push in the slider and remove the transmission control cable from the shift lever assembly as shown in the illustration



c.

for TMC Made:

i.
C365188C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the end of the transmission control cable assembly from the floor shift shift lever assembly.


ii.
C365189C01
1.542,1.656 1.625,1.417 true 1.427,1.656 1.635,1.844 0.208,0.188 10 true *1
*1 Nut
V100135

Rotate approximately 180°
V113147

Remove in this Direction


Rotate the nut approximately 180° in the direction shown in the illustration, and while holding the nut in that position, disconnect the transmission control cable assembly from the shift lever plate.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.




d.
C327175

Remove the nut to disconnect the transmission control cable assembly from the control shaft lever.


e.

Remove the clip to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.


f.
C365141

Remove the nut.


g.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


h.
C365142

Remove the 2 nuts and transmission control cable assembly from the vehicle body.