The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold converter sub-assembly (TWC: Front Catalyst) removal/installation are shown below.
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold converter sub-assembly.
Touching high-temperature areas such as the engine and exhaust manifold converter sub-assembly could result in burns.
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
1.REMOVE INTERCOOLER ASSEMBLY
2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55737B
3.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
55735A
4.REMOVE WATER GUARD PLATE LH (for TMC Made RHD)
55736D
5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH
55735C
6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH
55701J
7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
55225
9.REMOVE DASH PANEL HEAT INSULATOR
for LHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
53141F
10.REMOVE RADIATOR COVER
17751
11.REMOVE NO. 1 AIR CLEANER INLET
17705
12.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
82121
13.REMOVE ENGINE WIRE
|
Bolt |
|
Nut |
|
Connector |
Disconnect the 7 connectors.
Remove the bolt and nut.
Disengage the 3 wire harness clamps.
Remove the 2 bolts and wire harness clamp bracket from the cylinder head sub-assembly.
12261
14.REMOVE VENTILATION HOSE
| *1 | Ventilation Hose |
| *2 | No. 4 Ventilation Hose |
Slide the 2 clips and remove the ventilation hose from the cylinder head cover sub-assembly and inlet No. 1 air duct sub-assembly.
Slide the 2 clips and remove the No. 4 ventilation hose from the ventilation ejector and inlet No. 1 air duct sub-assembly.
12217
15.REMOVE VENTILATION EJECTOR
Remove the bolt and separate the air tube assembly from the cylinder head cover sub-assembly.
Remove the 2 bolts and ventilation ejector from the cylinder head cover sub-assembly.
Remove the O-ring from the cylinder head cover sub-assembly.
17360A
16.REMOVE AIR TUBE ASSEMBLY
| *1 | No. 2 Intercooler Water Hose |
| *2 | No. 3 Intercooler Water Hose |
Slide the 2 clips and disconnect the No. 2 intercooler water hose and No. 3 intercooler water hose from the turbocharger sub-assembly.
| *1 | No. 2 Intercooler Water Hose |
| *2 | No. 3 Intercooler Water Hose |
Disconnect the No. 2 intercooler water hose and No. 3 intercooler water hose from the No. 1 water hose clamp bracket.
Loosen the hose clamp and remove the air tube assembly from the turbocharger sub-assembly.
25819
17.REMOVE VACUUM REGULATING VALVE ASSEMBLY
| *1 | No. 2 Vacuum Transmitting Hose |
| *2 | No. 3 Vacuum Transmitting Hose |
| *3 | Vacuum Regulating Valve Assembly |
| *4 | No. 2 Vacuum Switching Valve Bracket |
Disconnect the No. 2 vacuum transmitting hose and No. 3 vacuum transmitting hose from the vacuum regulating valve assembly.
Remove the 3 bolts and vacuum regulating valve assembly and No. 2 vacuum switching valve bracket from the cylinder head sub-assembly.
17301C
18.REMOVE INLET NO. 1 AIR DUCT SUB-ASSEMBLY
Disconnect the No. 1 vacuum transmitting hose assembly from the vacuum tank.
Remove the 2 bolts and vacuum tank from the inlet No. 1 air duct sub-assembly.
Disconnect the No. 1 vacuum transmitting hose assembly from the vacuum pump assembly.
Remove the bolt and disconnect the inlet No. 1 air duct sub-assembly from the fuel pump protector.
Disconnect the intake air control valve (air by-pass valve assembly) connector.
| *1 | No. 2 Vacuum Transmitting Hose Assembly |
| *2 | Inlet No. 1 Air Duct Sub-assembly |
Disconnect the No. 2 vacuum transmitting hose assembly from the turbocharger sub-assembly.
Loosen the hose clamp and remove the inlet No. 1 air duct sub-assembly from the turbocharger sub-assembly.
89467B
19.REMOVE AIR FUEL RATIO SENSOR
12611
20.REMOVE NO. 1 ENGINE COVER
Remove the No. 1 engine cover from the cylinder head cover sub-assembly and cylinder head sub-assembly.
58166
21.REMOVE FRONT FLOOR COVER LH (w/ Cover)
58165B
22.REMOVE FRONT FLOOR COVER RH (w/ Cover)
Perform the same procedure as for the front floor cover LH.
57533B
23.REMOVE FRONT FLOOR CENTER BRACE
17410
24.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 2WD)
Disconnect the heated oxygen sensor connector.
Disengage the wire harness clamps.
Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and tail exhaust pipe assembly.
Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.
Remove the 2 exhaust pipe gaskets from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and tail exhaust pipe assembly.
17420K
25.REMOVE NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for AWD)
Remove the 4 bolts and disconnect the No. 2 center exhaust pipe assembly (TWC: Rear Catalyst) from the front exhaust pipe assembly and tail exhaust pipe assembly.
Remove the No. 2 center exhaust pipe assembly (TWC: Rear Catalyst) from the 4 exhaust pipe supports.
17410
26.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for AWD)
Disconnect the heated oxygen sensor connector.
Disengage the wire harness clamp.
Remove the 2 nuts and disconnect the front exhaust pipe assembly from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
Remove the exhaust pipe gasket from the front exhaust pipe assembly.
58151
27.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
Remove the 3 nuts and front No. 1 floor heat insulator from the vehicle body.
17163
28.REMOVE NO. 1 HEAT INSULATOR BRACKET (for 2WD)
Perform this procedure when it is necessary to replace the No. 1 heat insulator bracket.
Loosen the 3 bolts of the manifold support bracket.
Distortion may have occurred due to high temperatures.
Do not remove the 3 bolts. Only loosen them.
Remove the bolt, nut and drive shaft heat insulator sub-assembly from the No. 1 heat insulator bracket and manifold support bracket.
Remove the 2 bolts and No. 1 heat insulator bracket from the cylinder block sub-assembly.
12321B
29.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY (for 2WD)
Loosen the 3 bolts of the manifold support bracket.
Distortion may have occurred due to high temperatures.
Do not remove the 3 bolts. Only loosen them.
Remove the bolt, nut and drive shaft heat insulator sub-assembly from the No. 1 heat insulator bracket and manifold support bracket.
25591
30.REMOVE MANIFOLD SUPPORT BRACKET (for 2WD)
Remove the 3 bolts and manifold support bracket from the cylinder block sub-assembly and exhaust manifold converter sub-assembly (TWC: Front Catalyst).
25591
31.REMOVE MANIFOLD SUPPORT BRACKET (for AWD)
Remove the 3 bolts and manifold support bracket from the cylinder block sub-assembly and exhaust manifold converter sub-assembly (TWC: Front Catalyst).
37117B
32.REMOVE PROPELLER SHAFT HEAT INSULATOR (for AWD)
Remove the 3 bolts and propeller shaft heat insulator from the transfer assembly.
37109A
33.REMOVE PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY (for AWD)
Remove the 2 bolts and propeller shaft heat insulator bracket sub-assembly from the transfer assembly.
25586
34.REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR (for AWD)
w/ Differential Pressure Sensor:
Remove the nut, 3 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
w/o Differential Pressure Sensor:
Remove the 4 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
25587
35.REMOVE NO. 2 MANIFOLD CONVERTER INSULATOR (for AWD)
Remove the 3 bolts and No. 2 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
17272
36.REMOVE NO. 2 TURBO INSULATOR
Remove the 2 bolts and No. 2 turbo insulator from the cylinder head sub-assembly and heat insulator bracket.
25586
37.REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR (for 2WD)
Remove the 3 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
25051
38.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)
| *A | for 2WD |
| *B | for AWD |
Remove the 4 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the turbocharger sub-assembly.
17279
39.REMOVE OUTLET TURBINE ELBOW GASKET
Remove the outlet turbine elbow gasket from the turbocharger sub-assembly.
25733A
40.REMOVE NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)
for 2WD:
Slide the 2 clips and remove the vacuum transmitting hose from the differential pressure sensor and No. 1 vacuum pipe.
Using a 14 mm union nut wrench, disconnect the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.
Remove the nut and No. 1 vacuum pipe.
for AWD:
Slide the 2 clips and remove the vacuum transmitting hose from the differential pressure sensor and No. 1 vacuum pipe.
Using a 14 mm union nut wrench, disconnect the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.
Remove the nut and No. 1 vacuum pipe.
41.REMOVE STUD BOLT (for AWD)
If a stud bolt is deformed or its threads are damaged, replace it.
w/ Differential Pressure Sensor:
Using an E10 "TORX" socket wrench, remove the 2 stud bolts.
Using an E7 "TORX" socket wrench, remove the stud bolt.
w/o Differential Pressure Sensor:
Using an E10 "TORX" socket wrench, remove the 2 stud bolts.