This DTC is stored when the blind spot monitor sensor LH (B) judges that there is a communication problem with the blind spot monitor sensor RH (A).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U117787 | Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message | The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor RH (A) | ·
Open or short in CAN bus main wire or connector ·
Open or short in CAN bus wire or connector ·
Open or short in No. 6 junction connector ·
Clearance warning ECU assembly ·
Blind spot monitor sensor LH (B) ·
Power source circuit of blind spot monitor sensor LH (B) ·
Blind spot monitor sensor LH (B) ground circuit ·
Blind spot monitor sensor RH (A) |
| U117887 | Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message | The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor LH (B) | ·
Open or short in CAN bus main wire or connector ·
Open or short in CAN bus wire or connector ·
Open or short in No. 6 junction connector ·
Clearance warning ECU assembly ·
Blind spot monitor sensor RH (A) ·
Power source circuit of blind spot monitor sensor RH (A) ·
Blind spot monitor sensor RH (A) ground circuit ·
Blind spot monitor sensor LH (B) |
for TMMT Made
for TMC Made
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117787 is only output | A |
| DTC U117887 is only output | B |
| DTC U117787 and U117887 are output | C |
A
B
C
Disconnect the cable from the negative (-) battery terminal.
Disconnect the blind spot monitor sensor RH (A) connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M63-1 (CA2P) - M63-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>Power Source Circuit
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>Power Source Circuit
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the blind spot monitor sensor LH (B) connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M62-1 (CA2P) - M62-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>Power Source Circuit
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>Power Source Circuit
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
| *A | for TMMT Made |
| *B | for TMC Made |
| *1 | DLC3 |
| *a | Component with harness connected
(No. 6 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
for TMMT Made
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| M104-6 (CANH) - M104-17 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or more: Open circuit in main bus lines | |||
| M104-6 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH short to ground |
| M104-17 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL short to ground |
| M104-6 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| M104-17 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
for TMC Made
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| M104-3 (CANH) - M104-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or more: Open circuit in main bus lines | |||
| M104-3 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH short to ground |
| M104-14 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL short to ground |
| M104-3 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| M104-14 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| Open circuit in CAN main bus lines | B |
| Short circuit between bus lines | C |
·
Short to ground ·
+B short |
D |
A
B
C
D
Disconnect the clearance warning ECU assembly connector.
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F142-37 (CANH) - F142-38 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117787 and U117887 are output | A |
| DTC U117787 and U117887 are not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *a | Front view of wire harness connector
(to No. 6 Junction Connector) |
| *b | to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMMT Made) |
| *c | to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMMT Made) |
| *d | to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMC Made) |
| *e | to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMC Made) |
| *f | to Clearance Warning ECU Assembly CAN Wire |
Disconnect the No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
for TMMT Made
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-7 (CANH) - M104-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-6 (CANH) - M104-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-5 (CANH) - M104-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
for TMMT Made
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-2 (CANH) - M104-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-3 (CANH) - M104-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-5 (CANH) - M104-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
Reconnect the No. 6 junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M63-1 (CA2P) - M63-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 6 junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M62-1 (CA2P) - M62-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M104 No. 6 junction connector.
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Disconnect the clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F142-37 (CANH) - F142-38 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 6 Junction Connector) |
| *b | to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMMT Made) |
| *c | to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMMT Made) |
| *d | to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMC Made) |
| *e | to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMC Made) |
| *f | to Clearance Warning ECU Assembly CAN Wire |
Disconnect the No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
for TMMT Made
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-7 (CANH) - M104-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-6 (CANH) - M104-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-5 (CANH) - M104-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
for TMMT Made
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-2 (CANH) - M104-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-3 (CANH) - M104-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| M104-5 (CANH) - M104-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
Reconnect the M104 No. 6 junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M62-1 (CA2P) - M62-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M104 No. 6 junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M63-1 (CA2P) - M63-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M104 No. 6 junction connector.
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Disconnect the clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F142-37 (CANH) - F142-38 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M104 No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 Junction Connector) |
*b | to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMMT Made) |
| *c | to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMMT Made) | *d | to Blind Spot Monitor Sensor LH (B) CAN Main Wire (for TMC Made) |
| *e | to Blind Spot Monitor Sensor RH (A) CAN Main Wire (for TMC Made) | *f | to Clearance Warning ECU Assembly CAN Wire |
for TMMT Made
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-7 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-18 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-7 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-18 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-6 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-17 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-6 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-17 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-5 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-16 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-5 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-16 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
for TMC Made
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-2 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-13 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-2 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-13 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-3 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-14 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-3 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-14 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-5 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-16 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M104-5 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M104-16 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
Reconnect the M104 No. 6 junction connector.
Disconnect the M62 blind spot monitor sensor LH (B) connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M62-1 (CA2P) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M62-6 (CA2N) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M62-1 (CA2P) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M62-6 (CA2N) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M104 No. 6 junction connector.
Disconnect the M63 blind spot monitor sensor RH (A) connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M63-1 (CA2P) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M63-6 (CA2N) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M63-1 (CA2P) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M63-6 (CA2N) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M104 No. 6 junction connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Disconnect the F142 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F142-37 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F142-38 (CANL) - F144-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F142-37 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F142-38 (CANL) - F144-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG