Home › Engine / Hybrid System › 3ZR-FAE (FUEL) › FUEL INJECTOR › from 2020.08
RM32H0E _51 Engine / Hybrid System _060184 3ZR-FAE FUEL _0295033 FUEL INJECTOR A

3ZR-FAE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of fuel injector assembly Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Simple intelligent parking assist system*1 Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 28800 6.REMOVE BATTERY

Hide 82121 7.DISCONNECT ENGINE WIRE

a.
A393409

Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.


Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 10.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A280216

Remove the 2 nuts and wire harness clamp bracket from the camshaft housing sub-assembly.


Hide 23901 11.DISCONNECT FUEL TUBE SUB-ASSEMBLY

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


a.
A294335C01
2.865,0.854 2.771,1.188 2.771,1.188 2.667,0.854 false 2.688,1.198 3,1.396 0.313,0.198 10 *a
*a Claw


Disengage the 2 claws to remove the No. 2 fuel pipe clamp.

NOTICE:

Do not reuse the No. 2 fuel pipe clamp.



b.

Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

i.
A062165N01
1.979,0.719 2.49,1.635 2.49,1.635 2.021,1.854 true 2.531,1.552 2.844,1.729 0.313,0.177 10 SST

Install SST (fuel hose puller) to the fuel tube connector as shown in the illustration.

SST
09268-21011  


ii.
A300492C04
2.188,1.396 2.49,1.698 2.49,1.698 2.688,1.698 false 0.396,0.281 0.802,0.281 0.802,0.281 0.802,0.427 true 0.531,0.604 0.531,0.281 false 1.26,1.24 1.26,0.729 1.26,0.729 1.073,0.729 true 0.896,0.958 1.26,0.958 false 0.229,0.198 0.479,0.385 0.25,0.188 10 false *a 2.74,1.646 3.135,1.844 0.396,0.198 10 false SST 1.177,1.24 1.49,1.396 0.313,0.156 10 false *a
*a Retainer (4 places)


Turn SST (fuel hose puller), align the retainers inside the fuel tube connector with the SST (fuel hose puller) chamfers and insert SST (fuel hose puller) into the fuel tube connector.


iii.

Mount the retainer of the fuel tube connector onto the chamfered part of SST (fuel hose puller).


iv.
A158904C23
0.469,1.385 0.469,1.052 false 1.271,1.448 1.271,1.052 true 2.167,1.583 2.167,1.25 false 2.833,1.344 2.833,1.01 false 2.063,0.531 1.583,0.24 1.583,0.24 1.417,0.24 true 0.917,0.594 0.833,0.26 0.833,0.26 0.667,0.26 false 1.146,1.438 1.479,1.438 1.479,1.438 1.479,1.052 true 0.479,0.177 0.792,0.333 0.313,0.156 10 false *1 1.208,0.146 1.521,0.302 0.313,0.156 10 false *a 0.406,1.406 0.719,1.563 0.313,0.156 10 false *b 0.938,1.344 1.25,1.5 0.313,0.156 10 false *c 2.104,1.604 2.417,1.76 0.313,0.156 10 false *d 2.771,1.365 3.083,1.521 0.313,0.156 10 false *e
*1 Fuel Tube Sub-assembly
*a Retainer
*b Nylon Tube
*c O-ring
*d Fuel Tube Connector
*e Fuel Pipe


Slide SST (fuel hose puller) and the fuel tube connector together until they make a "click" sound, and then disconnect the fuel tube connector.

NOTICE:
·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Do not forcibly bend, twist or turn the nylon tube.




v.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vi.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



Hide 89421 12.REMOVE VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 89426 13.REMOVE VACUUM SENSOR BRACKET

Hide 23807 14.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A293911

Remove the bolt to separate the clamp from the cylinder head sub-assembly.


b.
A153007

Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 fuel injector assemblies.

NOTICE:

Do not drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



Hide 23807V 15.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A153008

Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.


Hide 23291 16.REMOVE INJECTOR VIBRATION INSULATOR

a.
A153010

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 23250 17.REMOVE FUEL INJECTOR ASSEMBLY

a.
A153009

Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.


b.

Remove the O-ring from each fuel injector assembly.


c.

For reinstallation, attach a tag or label with the corresponding cylinder number to each fuel injector assembly.

NOTICE:

Protect the fuel injector assemblies by covering them with plastic bags.