Refer to DTC P007A11.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P007A11
When DTC P007A15 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 45°C (113°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P007A15 | Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Battery or Open | The intake air temperature sensor output voltage is higher than 4.9 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in intake air temperature sensor (No. 2 turbo pressure sensor) circuit ·
No. 2 turbo pressure sensor (intake air temperature sensor) ·
ECM |
Does not come on | DTC stored | SAE Code: P007D |
When this DTC is output, check the intake air temperature (for intake manifold) in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temperature B1S1 (Turbo).
| DTC No. | Intake Air Temperature B1S1 (Turbo) | Malfunction |
|---|---|---|
| P007A15 | -40°C (-40°F) | ·
Short in THIM circuit to power source circuit ·
Open in THIM circuit ·
Open in EPIM circuit |
If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the intake air temperature sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores this DTC.
Example:
If the intake air temperature sensor output voltage is higher than 4.9 V for 3 seconds or more, the ECM store this DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P007A15.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P007A11.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P007A11
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *1 | No. 2 Turbo Pressure Sensor | *2 | ECM |
| *a | Front view of wire harness connector
(to No. 2 Turbo Pressure Sensor) |
- | - |
Disconnect the No. 2 turbo pressure sensor connector.
Connect terminals 4 (THIM) and 2 (E2) of the No. 2 turbo pressure sensor connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temperature B1S1 (Turbo).
| Tester Display |
|---|
| Intake Air Temperature B1S1 (Turbo) |
According to the display on the GTS, read the Data List.
140°C (284°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C39 No. 2 turbo pressure sensor connector.
Disconnect the C62*1 or C74*2 ECM connector.
*1: for TMMT Made
*2: for TMC Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-4 (THIM) - C62-107 (THIM) | Always | Below 1 Ω |
| C39-2 (E2) - C62-137 (EPIM) | Always | Below 1 Ω |
| C39-4 (THIM) or C62-107 (THIM) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-4 (THIM) - C74-107 (THIM) | Always | Below 1 Ω |
| C39-2 (E2) - C74-137 (EPIM) | Always | Below 1 Ω |
| C39-4 (THIM) or C74-107 (THIM) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG