Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P035113  Ignition Coil "A" Circuit Open  P035213  Ignition Coil "B" Circuit Open  P035313  Ignition Coil "C" Circuit Open  P035413  Ignition Coil "D" Circuit Open  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P035113 is output, check the No. 1 ignition coil (No. 1 cylinder) circuit.

·

If DTC P035213 is output, check the No. 1 ignition coil (No. 2 cylinder) circuit.

·

If DTC P035313 is output, check the No. 1 ignition coil (No. 3 cylinder) circuit.

·

If DTC P035413 is output, check the No. 1 ignition coil (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one No. 1 ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A299859E10
5.417,1.052 5.667,0.583 5.667,0.583 5.833,0.583 false 4.5,1.292 4.25,0.75 4.25,0.75 4.083,0.75 false 0.458,1.25 2.24,1.458 1.781,0.208 10 false Crankshaft Position Sensor 0.5,3.021 2.167,3.188 1.667,0.167 10 false Camshaft Position Sensor 0.354,4.333 2.271,5 1.917,0.667 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 3.031,1.354 3.365,1.521 0.333,0.167 10 false IGT1 3.031,1.667 3.365,1.833 0.333,0.167 10 false IGF1 3.031,2.667 3.365,2.833 0.333,0.167 10 false IGT2 3.031,4 3.365,4.167 0.333,0.167 10 false IGT3 3.031,5.323 3.365,5.49 0.333,0.167 10 false IGT4 2.885,5.833 3.219,6 0.333,0.167 10 false ECM 4.375,5.865 5.479,6.427 1.104,0.563 10 false No. 1 Ignition Coil (No. 4 Cylinder) 4.354,4.542 5.469,5.021 1.115,0.479 10 false No. 1 Ignition Coil (No. 3 Cylinder) 4.344,3.24 5.458,3.719 1.115,0.479 10 false No. 1 Ignition Coil (No. 2 Cylinder) 5.958,1.781 6.802,2.042 0.844,0.26 10 false Spark Plug 5.958,3 6.74,3.271 0.781,0.271 10 false Spark Plug 5.958,4.313 6.75,4.583 0.792,0.271 10 false Spark Plug 5.948,5.625 6.729,5.927 0.781,0.302 10 false Spark Plug 5.917,0.5 7.031,0.844 1.115,0.344 10 false No. 1 Ignition Coil (No. 1 Cylinder) 4.667,0.396 6.021,0.563 1.354,0.167 10 false from Battery 3.667,0.667 4.083,0.833 0.417,0.167 10 false Igniter

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P035113 Ignition Coil "A" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil

·

ECM


Comes on DTC stored SAE Code:
P0351
P035213 Ignition Coil "B" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil

·

ECM


Comes on DTC stored SAE Code:
P0352
P035313 Ignition Coil "C" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil

·

ECM


Comes on DTC stored SAE Code:
P0353
P035413 Ignition Coil "D" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil

·

ECM


Comes on DTC stored SAE Code:
P0354

A299080E13
0.125,1.281 0.458,1.677 0.333,0.396 10 false CH1 (IGT) 0.146,1.802 0.615,2.271 0.469,0.469 10 false CH2 (IGF1) 3.021,2.167 3.385,2.354 0.365,0.188 10 false GND 3.021,1.542 3.427,1.771 0.406,0.229 10 false GND 0.146,0.51 1.375,0.708 1.229,0.198 10 false 2 V/DIV. 1.438,2.604 2.667,2.802 1.229,0.198 10 false 20 ms./DIV.

Reference: Inspection using an oscilloscope.


HINT:
·

The correct waveform is as shown.


·

While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.



ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

MONITOR DESCRIPTION

A212405E57
1.781,1.646 2.177,1.823 0.396,0.177 10 false ECM 2.958,1.302 3.229,1.49 0.271,0.188 10 false IGT 2.948,1.729 3.229,1.885 0.281,0.156 10 false IGF 4.156,1.51 4.594,1.656 0.438,0.146 10 false Igniter 5.396,1.344 6.167,1.521 0.771,0.177 10 false Ignition Coil 4.469,2.354 6.167,2.542 1.698,0.188 10 false No. 1 Ignition Coil 0.208,3.115 1.146,3.448 0.938,0.333 10 false Ignition Signal (IGT) 1.646,3.542 2.135,3.729 0.49,0.188 10 false Normal 1.385,3.948 2.156,4.135 0.771,0.188 10 false Malfunction 0.26,3.906 1.146,4.771 0.885,0.865 10 false Ignition Confirmation Signal (IGF) 3.448,4.51 4.625,4.688 1.177,0.177 10 false Circuit Malfunction 5.948,4.969 6.313,5.167 0.365,0.198 10 false Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P035113, P035213, P035313 or P035413.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A384826E11
0.49,3.115 2.344,3.771 1.854,0.656 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition or Starter Switch Assembly*2 3.771,1.083 4.219,1.313 0.448,0.229 10 false +B 3.771,1.417 4.24,1.604 0.469,0.188 10 false GND 3.771,2.792 4.146,3 0.375,0.208 10 false +B 3.76,3.115 4.198,3.333 0.438,0.219 10 false GND 3.781,4.458 4.135,4.646 0.354,0.188 10 false +B 3.802,4.771 4.25,4.969 0.448,0.198 10 false GND 3.771,6.042 4.198,6.24 0.427,0.198 10 false +B 3.74,6.438 4.302,6.635 0.563,0.198 10 false GND 4.854,6.115 5.24,6.313 0.385,0.198 10 false IGT4 4.865,4.458 5.24,4.656 0.375,0.198 10 false IGT3 4.833,2.792 5.198,2.99 0.365,0.198 10 false IGT2 4.823,1.104 5.208,1.323 0.385,0.219 10 false IGT1 4.865,1.438 5.177,1.625 0.313,0.188 10 false IGF 4.927,3.135 5.25,3.313 0.323,0.177 10 false IGF 4.865,4.792 5.156,4.979 0.292,0.188 10 false IGF 4.917,6.458 5.24,6.667 0.323,0.208 10 false IGF 3.708,1.927 4.833,2.51 1.125,0.583 10 false No. 1 Ignition Coil (No. 1 Cylinder) 3.698,3.646 4.833,4.281 1.135,0.635 10 false No. 1 Ignition Coil (No. 2 Cylinder) 3.698,5.302 5.01,5.927 1.313,0.625 10 false No. 1 Ignition Coil (No. 3 Cylinder) 3.708,6.99 4.865,7.729 1.156,0.74 10 false No. 1 Ignition Coil (No. 4 Cylinder) 0.552,5.885 1.698,6.271 1.146,0.385 10 false Battery 6.188,7.042 6.813,7.313 0.625,0.271 10 false ECM 5.875,6.344 6.281,6.531 0.406,0.188 10 false IGF1 5.833,5.906 6.333,6.135 0.5,0.229 10 false IGT4 5.865,4.333 6.354,4.563 0.49,0.229 10 false IGT3 5.844,2.688 6.344,2.885 0.5,0.198 10 false IGT2 5.865,0.958 6.365,1.177 0.5,0.219 10 false IGT1 3.698,6.781 4.26,6.979 0.563,0.198 10 false C24 3.583,5.948 4.01,6.146 0.427,0.198 10 false 1 3.583,6.344 4.01,6.542 0.427,0.198 10 false 4 5.229,6.344 5.656,6.542 0.427,0.198 10 false 2 5.229,5.948 5.656,6.146 0.427,0.198 10 false 3 5.958,6.844 6.979,7.104 1.021,0.26 10 false C62*3, C74*4 5.5,6.365 5.906,6.552 0.406,0.188 10 false 101 5.573,5.958 5.823,6.198 0.25,0.24 10 false 39 5.604,4.333 5.854,4.573 0.25,0.24 10 false 40 5.594,2.677 5.844,2.917 0.25,0.24 10 false 41 5.594,0.99 5.844,1.229 0.25,0.24 10 false 42 5.219,4.344 5.646,4.542 0.427,0.198 10 false 3 3.583,4.656 4.01,4.854 0.427,0.198 10 false 4 3.583,4.354 4.01,4.552 0.427,0.198 10 false 1 5.219,4.667 5.646,4.865 0.427,0.198 10 false 2 5.219,2.688 5.646,2.885 0.427,0.198 10 false 3 5.219,3 5.646,3.198 0.427,0.198 10 false 2 3.573,2.688 4,2.885 0.427,0.198 10 false 1 3.573,0.969 4,1.167 0.427,0.198 10 false 1 3.573,3 4,3.198 0.427,0.198 10 false 4 3.583,1.313 4.01,1.51 0.427,0.198 10 false 4 5.219,1.313 5.646,1.51 0.427,0.198 10 false 2 5.219,0.969 5.646,1.167 0.427,0.198 10 false 3 3.729,1.792 4.292,1.99 0.563,0.198 10 false C21 3.688,3.479 4.25,3.677 0.563,0.198 10 false C22 3.708,5.125 4.271,5.323 0.563,0.198 10 false C23 0.365,5.052 1.365,5.406 1,0.354 10 false BATT MAIN 2.344,1.281 2.802,1.479 0.458,0.198 10 false IGN 1.021,1.938 2.25,2.135 1.229,0.198 10 false IG2 NO. 1 0.865,2.531 2.365,2.802 1.5,0.271 10 false No. 1 Integration Relay 0.854,2.365 1.167,2.563 0.313,0.198 10 false 1A 1.865,1.5 2.01,1.677 0.146,0.177 9 false 7 0.781,1.5 0.938,1.698 0.156,0.198 10 false 8 1.844,1.021 2,1.219 0.156,0.198 10 false 9 0.708,0.99 1.021,1.188 0.313,0.198 10 false 10 0.531,6.406 2.885,6.99 2.354,0.583 10 false *1: w/ Entry and Start System 0.531,6.781 2.927,7.229 2.396,0.448 10 false *2: w/o Entry and Start System 0.385,4.313 1.167,4.667 0.781,0.354 10 false IG2 MAIN 0.531,7.167 2.927,7.615 2.396,0.448 10 false *3: for TMMT Made 0.542,7.542 2.885,7.802 2.344,0.26 10 false *4: for TMC Made

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (DTC P035113, P035213, P035313 OR P035413)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Read the DTCs.

Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the No. 1 ignition coil.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)
A347474C29
0.188,1.073 0.573,1.313 0.385,0.24 0.188,1.479 0.573,1.719 0.385,0.24 0.188,1.875 0.573,2.115 0.385,0.24 0.188,2.271 0.573,2.51 0.385,0.24 1.083,2.792 1.271,2.281 true 0.188,0.177 0.646,0.375 0.458,0.198 10 false *a 0.25,1.115 0.708,1.313 0.458,0.198 10 false C21 0.25,1.521 0.708,1.719 0.458,0.198 10 false C22 0.25,1.917 0.708,2.115 0.458,0.198 10 false C23 0.26,2.313 0.719,2.51 0.458,0.198 10 false C24 0.99,2.813 1.448,3.01 0.458,0.198 10 false +B
*a Front view of wire harness connector
(to No. 1 Ignition Coil Assembly)


a.

Disconnect the No. 1 ignition coil connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C21-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C22-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C23-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C24-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
a.

Disconnect the C21, C22, C23 and C24 No. 1 ignition coil connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C21-4 (GND) - Body ground Always Below 1 Ω
C22-4 (GND) - Body ground Always Below 1 Ω
C23-4 (GND) - Body ground Always Below 1 Ω
C24-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)

4.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
a.

Disconnect the C21, C22, C23 and C24 No. 1 ignition coil connector.


b.

Disconnect the C62*1 or C74*2 ECM connector.

*1: for TMMT Made

*2: for TMC Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
C21-2 (IGF) - C62-101 (IGF1) Always Below 1 Ω
C22-2 (IGF) - C62-101 (IGF1) Always Below 1 Ω
C23-2 (IGF) - C62-101 (IGF1) Always Below 1 Ω
C24-2 (IGF) - C62-101 (IGF1) Always Below 1 Ω
C21-3 (IGT1) - C62-42 (IGT1) Always Below 1 Ω
C22-3 (IGT2) - C62-41 (IGT2) Always Below 1 Ω
C23-3 (IGT3) - C62-40 (IGT3) Always Below 1 Ω
C24-3 (IGT4) - C62-39 (IGT4) Always Below 1 Ω
C21-2 (IGF) or C62-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C22-2 (IGF) or C62-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C23-2 (IGF) or C62-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C24-2 (IGF) or C62-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C21-3 (IGT1) or C62-42 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C22-3 (IGT2) or C62-41 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C23-3 (IGT3) or C62-40 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C24-3 (IGT4) or C62-39 (IGT4) - Body ground and other terminals Always 10 kΩ or higher

for TMC Made
Tester Connection Condition Specified Condition
C21-2 (IGF) - C74-101 (IGF1) Always Below 1 Ω
C22-2 (IGF) - C74-101 (IGF1) Always Below 1 Ω
C23-2 (IGF) - C74-101 (IGF1) Always Below 1 Ω
C24-2 (IGF) - C74-101 (IGF1) Always Below 1 Ω
C21-3 (IGT1) - C74-42 (IGT1) Always Below 1 Ω
C22-3 (IGT2) - C74-41 (IGT2) Always Below 1 Ω
C23-3 (IGT3) - C74-40 (IGT3) Always Below 1 Ω
C24-3 (IGT4) - C74-39 (IGT4) Always Below 1 Ω
C21-2 (IGF) or C74-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C22-2 (IGF) or C74-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C23-2 (IGF) or C74-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C24-2 (IGF) or C74-101 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C21-3 (IGT1) or C74-42 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C22-3 (IGT2) or C74-41 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C23-3 (IGT3) or C74-40 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C24-3 (IGT4) or C74-39 (IGT4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 IGNITION COIL - ECM)

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)
a.

Disconnect the C21, C22, C23 and C24 No. 1 ignition coil connectors.


b.

Disconnect the 1A No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C21-1 (+B) - 1A-9 Always Below 1 Ω
C22-1 (+B) - 1A-9 Always Below 1 Ω
C23-1 (+B) - 1A-9 Always Below 1 Ω
C24-1 (+B) - 1A-9 Always Below 1 Ω
C21-1 (+B) or 1A-9 - Body ground and other terminals Always 10 kΩ or higher
C22-1 (+B) or 1A-9 - Body ground and other terminals Always 10 kΩ or higher
C23-1 (+B) or 1A-9 - Body ground and other terminals Always 10 kΩ or higher
C24-1 (+B) or 1A-9 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)
a.

Inspect the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG