INSTALLATION
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL NO. 2 BACK WINDOW GLASS STOPPER |
 |
Using a brush or sponge, coat the application area of the No. 2 stoppers with Primer G.
- NOTICE:
- Do not apply too much primer.
- Allow the primer coating to dry for 3 minutes or more.
- Do not keep any of the opened Primer G for later use.
- HINT:
- If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Install 2 new No. 2 stoppers onto the back window glass, as shown in the illustration.
- HINT:
- Only 2-piece type No. 2 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.
- Standard dimension:
Area
|
Dimension
|
A
|
16.4 mm (0.645 in.)
|


| 2.
INSTALL NO. 1 BACK WINDOW GLASS STOPPER |
 |
- Install 2 new No. 1 stoppers to the vehicle body, as shown in the illustration.
- HINT:
- Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.
| 3.
INSTALL BACK WINDOW MOULDING |
 |
- Using a brush or sponge, coat the application area of the moulding with Primer G.
- NOTICE:
- Do not apply too much primer.
- Allow the primer coating to dry for 3 minutes or more.
- Do not keep any of the opened Primer G for later use.
- HINT:
- If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Install a new moulding onto the back window glass, as shown in the illustration.
- NOTICE:
- Align the joint of the new moulding with the ceramic notch.
| 4.
INSTALL BACK WINDOW GLASS ASSEMBLY |
 |
- Position the back window glass assembly.
Using a suction cup, place the back window glass assembly in the correct position.
Check that the whole contact surface of the back window glass rim is perfectly even.
Align the matchmarks on the back window glass and vehicle body.
- NOTICE:
- Check that the back window glass stoppers are attached to the vehicle body correctly.
Remove the back window glass assembly.
- Using a brush, coat the installation surface on the vehicle body with Primer M.
- NOTICE:
- Do not coat the adhesive with Primer M.
- Do not apply too much primer.
- Allow the primer coating to dry for 3 minutes or more.
- Do not keep any of the opened Primer M for later use.
- HINT:
- If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Using a brush or sponge, coat the application area of adhesive with Primer G.
- NOTICE:
- Do not apply too much primer.
- Allow the primer coating to dry for 3 minutes or more.
- Do not keep any of the opened Primer G for later use.
- HINT:
- If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
- Standard dimension:
Area
|
Dimension
|
a
|
10.75 mm (0.423 in.)
|
b
|
7.0 mm (0.275 in.)
|
c
|
10.25 mm (0.403 in.)
|
d
|
8.0 mm (0.315 in.)
|


Apply adhesive (Adhesive: TOYOTA genuine windshield glass adhesive or equivalent).
Cut off the tip of the cartridge nozzle, as shown in the illustration.
- HINT:
- After cutting off the tip, use all adhesive within the time described in the table below.
- Usage time frame:
Temperature
|
Tack-free Time
|
35°C (95°F)
|
15 minutes
|
20°C (68°F)
|
1 hour and 40 minutes
|
5°C (41°F)
|
8 hours
|
Load the sealer gun with cartridge.
Apply adhesive to the back window glass, as shown in the illustration.
- Standard dimension:
Area
|
Dimension
|
a
|
10.75 mm (0.423 in.)
|
b
|
10.25 mm (0.403 in.)
|
c
|
8.0 mm (0.315 in.)
|
d
|
12.0 mm (0.472 in.)
|
e
|
8.0 mm (0.315 in.)
|


- Install the back window glass assembly.
Using a suction cup, position the back window glass so that the matchmarks are aligned, and press it in gently along the rim.
- NOTICE:
- Check that the back window glass stoppers are attached to the vehicle body correctly.
- Check the clearance between the vehicle body and back window glass.
Lightly press the front surface of the back window glass to ensure a close fit.
- HINT:
- Press the glass with a force of 98 N (10 kgf, 22 lb) or more.
Hold the back window glass using protective tape until applied adhesive becomes hard.
- NOTICE:
- Do not drive the vehicle for the time described in the table below.
- Minimum time:
Temperature
|
Minimum time prior to driving vehicle
|
35°C (95°F)
|
1 hour and 30 minutes
|
20°C (68°F)
|
5 hours
|
5°C (41°F)
|
24 hours
|
- Connect the connectors.
- Connect the connector.
| 5.
INSPECT FOR LEAK AND REPAIR |
 |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 6.
INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) |
 |
Return the rear section of the roof headlining assembly to the original position (Click here).
| 7.
INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof) |
 |
Return the rear section of the roof headlining assembly to the original position (Click here).
| 8.
INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)
|
 |
- Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.
Engage the 4 claws.
- Engage the 6 claws and install the spot light assembly.
| 9.
INSTALL REAR ASSIST GRIP SUB-ASSEMBLY
|
 |
- HINT:
- Use the same procedure for the rear side and the front side.
| 10.
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
|
 |
- without Rear Spoiler:
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
Engage the 4 clips and 5 claws and install the package tray trim panel assembly.
Connect the connector.
- with Rear Spoiler:
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
Engage the 4 clips and 5 claws and install the package tray trim panel assembly.
| 11.
INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Spoiler)
|
 |
Connect the connector.
- Engage the 5 claws and 4 clips, and install the No. 2 package tray trim panel assembly.
| 12.
INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Spoiler)
|
 |
- Engage the 5 claws and 4 clips, and install the No. 2 package tray trim panel assembly.
| 13.
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
|
 |
- Pass the 3 rear seat belt floor anchors through the holes in the package tray trim panel assembly.
Insert the rear end of the package tray trim panel assembly into the rear window shade assembly.
Engage the 2 clips and install the package tray trim panel assembly.
| 14.
INSTALL REAR SEAT SHOULDER BELT HOLE COVER
|
 |
- Engage the 4 claws and install the rear seat shoulder belt hole cover.
| 15.
INSTALL REAR SEAT SHOULDER BELT COVER
|
 |
- Engage the 4 claws and install the rear seat shoulder belt cover.
- HINT:
- Use the same procedures for the RH side and the LH side.
| 16.
CONNECT REAR SEAT OUTER BELT ASSEMBLY LH
|
 |
- Connect the floor end of the rear seat outer belt assembly LH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the rear seat outer belt assembly LH to overlap the protruding part of the floor panel.
Check if the ELR locks.
- NOTICE:
- The check should be performed with the outer belt assembly LH installed.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
| 17.
CONNECT REAR SEAT OUTER BELT ASSEMBLY RH
|
 |
- Connect the floor end of the rear seat outer belt assembly RH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the rear seat outer belt assembly RH to overlap the protruding part of the floor panel.
Check if the ELR locks.
- NOTICE:
- The check should be performed with the outer belt assembly RH installed.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
| 18.
CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
|
 |
- Connect the floor end of the rear seat inner with center belt assembly LH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
Check if the ELR locks.
- NOTICE:
- The check should be performed with the outer belt assembly installed.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
| 19.
INSTALL NO. 1 SEAT BRACKET (for Fixed Seat Type)
|
 |
Install the No. 1 seat bracket with the 2 nuts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 20.
INSTALL ROOF SIDE INNER GARNISH LH
|
 |
- Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.
| 21.
INSTALL ROOF SIDE INNER GARNISH RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 22.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
- Install the rear door opening trim weatherstrip LH as shown in the illustration.
- NOTICE:
- After installation, check that the corners fit correctly.
| 23.
INSTALL REAR DOOR SCUFF PLATE LH
|
 |
- Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.
| 24.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
- Install the rear door opening trim weatherstrip RH as shown in the illustration.
- NOTICE:
- After installation, check that the corners fit correctly.
| 25.
INSTALL REAR DOOR SCUFF PLATE RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 26.
INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
|
 |
- Install the rear side seatback assembly with the bolt.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 27.
INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
|
| 28.
INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
|
 |
- Install the separate type rear seatback assembly with the 2 bolts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 29.
INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
|
 |
- Install the separate type rear seatback assembly with the 2 bolts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 30.
INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)
|
 |
- Place the seatback in the cabin.
- NOTICE:
- Be careful not to damage the vehicle body.
Install the rear seatback assembly with the 4 bolts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
- Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.
Install the floor anchor part with the bolt.
| 31.
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest) |
|
| 32.
INSTALL REAR SEAT HEADREST ASSEMBLY |
|
| 33.
INSTALL REAR SEAT CUSHION ASSEMBLY |
 |
for Fixed Seat Type (Click here)for Fold Down Seat Type (Click here)
| 34.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|
| 35.
INSPECT SRS WARNING LIGHT |
 |
(Click here)