2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as to when a switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM

E184615E03

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).


1. INSPECT RADIO RECEIVER

  1. E141020E25
    Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-7 (SW1) - F8-6 (SWG)
    No switch is pushed
    95 to 105 kΩ
    F8-7 (SW1) - F8-6 (SWG)
    Seek+ switch pushed
    Below 2.5 Ω
    F8-7 (SW1) - F8-6 (SWG)
    Seek- switch pushed
    313.5 to 346.5 Ω
    F8-7 (SW1) - F8-6 (SWG)
    Volume+ switch pushed
    959.5 to 1060.5 Ω
    F8-7 (SW1) - F8-6 (SWG)
    Volume- switch pushed
    3049.5 to 3370.5 Ω
    F8-8 (SW2) - F8-6 (SWG)
    No switch is pushed
    95 to 105 kΩ
    F8-8 (SW2) - F8-6 (SWG)
    MODE switch pushed
    Below 2.5 Ω
    F8-8 (SW2) - F8-6 (SWG)*2
    Voice switch pushed
    3049.5 to 3370.5 Ω
    F8-8 (SW2) - F8-6 (SWG)*2
    On Hook switch pushed
    313.5 to 346.5 Ω
    F8-8 (SW2) - F8-6 (SWG)*2
    Off Hook switch pushed
    959.5 to 1060.5 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver)
    1. *2: w/ Microphone



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT STEERING PAD SWITCH

  1. Disconnect the steering pad switch connector.E129804E05

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a1-10 (AU1) - a1-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    a1-10 (AU1) - a1-8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    a1-10 (AU1) - a1-8 (EAU)
    Seek- switch pushed
    313.5 to 346.5 Ω
    a1-10 (AU1) - a1-8 (EAU)
    Volume+ switch pushed
    959.5 to 1060.5 Ω
    a1-10 (AU1) - a1-8 (EAU)
    Volume- switch pushed
    3049.5 to 3370.5 Ω
    a1-9 (AU2) - a1-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    a1-9 (AU2) - a1-8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    a1-9 (AU2) - a1-8 (EAU)
    Voice switch pushed*11
    3049.5 to 3370.5 Ω
    a1-9 (AU2) - a1-8 (EAU)
    On Hook switch pushed*11
    313.5 to 346.5 Ω
    a1-9 (AU2) - a1-8 (EAU)
    Off Hook switch pushed*11
    959.5 to 1060.5 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch for 3 Spoke Type)
    *2
    Component without harness connected
    (Steering Pad Switch for 4 Spoke Type)
    *3
    Volume-
    *4
    Volume+
    *5
    Seek-
    *6
    Seek+
    *7
    MODE
    *8
    Off Hook*11
    *9
    On Hook*11
    *10
    Voice*11
    1. *11: w/ Microphone



NG
REPLACE STEERING PAD SWITCH
OK


3. INSPECT SPIRAL CABLE

  1. E168547E10
    Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-10 (AU1) - E18-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-9 (AU2) - E18-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral Cable)
    *2
    Steering Pad Switch Side
    *3
    Vehicle Side



NG
REPLACE SPIRAL CABLE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


← Steering Pad Switch Circuit (Oct 2006 – May 2009)Illumination Circuit (Jun 2006 – Sep 2006) →