2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as that when the switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM

E131852E01

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).


1. INSPECT RADIO RECEIVER

  1. E129800E02
    Disconnect the radio receiver connector F8.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    F8-7 (SW1) - F8-6 (SWG)
    No switch is pushed
    Approx. 100 kΩ
    F8-7 (SW1) - F8-6 (SWG)
    SEEK+ switch: push
    0 to 2.5 Ω
    F8-7 (SW1) - F8-6 (SWG)
    SEEK- switch: push
    Approx. 0.3 kΩ
    F8-7 (SW1) - F8-6 (SWG)
    VOL+ switch: push
    Approx. 1 kΩ
    F8-7 (SW1) - F8-6 (SWG)
    VOL- switch: push
    Approx. 3.1 kΩ
    F8-8 (SW2) - F8-6 (SWG)
    No switch is pushed
    Approx. 100 kΩ
    F8-8 (SW2) - F8-6 (SWG)
    MODE switch: push
    0 to 2.5 Ω



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.

  1. Measure the resistance according to the values in the table below.E136204E02

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    a1-10 (AU1) - a1-8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    a1-10 (AU1) - a1-8 (EAU)
    SEEK+ switch: push
    0 to 2.5 Ω
    a1-10 (AU1) - a1-8 (EAU)
    SEEK- switch: push
    Approx. 0.3 kΩ
    a1-10 (AU1) - a1-8 (EAU)
    VOL+ switch: push
    Approx. 1 kΩ
    a1-10 (AU1) - a1-8 (EAU)
    VOL- switch: push
    Approx. 3.1 kΩ
    a1-9 (AU2) - a1-8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    a1-9 (AU2) - a1-8 (EAU)
    MODE switch: push
    0 to 2.5 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


3. INSPECT SPIRAL CABLE

  1. I039337E59
    Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Spiral Cable Position
    Specified condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-10 (AU1) - E18-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-9 (AU2) - E18-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets below.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)



NG
REPLACE SPIRAL CABLE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


← Steering Pad Switch Circuit (Jun 2006 – Sep 2006)Steering Pad Switch Circuit (from Jun 2009) →