Steering Pad Switch Circuit
Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
This circuit sends an operation signal from the steering pad switch to the radio receiver.If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as that when the switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).
| 1. INSPECT RADIO RECEIVER |
Disconnect the radio receiver connector F8.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Condition
Specified condition
F8-7 (SW1) - F8-6 (SWG)
No switch is pushed
Approx. 100 kΩ
F8-7 (SW1) - F8-6 (SWG)
SEEK+ switch: push
0 to 2.5 Ω
F8-7 (SW1) - F8-6 (SWG)
SEEK- switch: push
Approx. 0.3 kΩ
F8-7 (SW1) - F8-6 (SWG)
VOL+ switch: push
Approx. 1 kΩ
F8-7 (SW1) - F8-6 (SWG)
VOL- switch: push
Approx. 3.1 kΩ
F8-8 (SW2) - F8-6 (SWG)
No switch is pushed
Approx. 100 kΩ
F8-8 (SW2) - F8-6 (SWG)
MODE switch: push
0 to 2.5 Ω
|
|
||||
| OK | ||
| ||
| 2. INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Measure the resistance according to the values in the table below.


- Standard resistance:
Tester connection
Condition
Specified condition
a1-10 (AU1) - a1-8 (EAU)
No switch is pushed
Approx. 100 kΩ
a1-10 (AU1) - a1-8 (EAU)
SEEK+ switch: push
0 to 2.5 Ω
a1-10 (AU1) - a1-8 (EAU)
SEEK- switch: push
Approx. 0.3 kΩ
a1-10 (AU1) - a1-8 (EAU)
VOL+ switch: push
Approx. 1 kΩ
a1-10 (AU1) - a1-8 (EAU)
VOL- switch: push
Approx. 3.1 kΩ
a1-9 (AU2) - a1-8 (EAU)
No switch is pushed
Approx. 100 kΩ
a1-9 (AU2) - a1-8 (EAU)
MODE switch: push
0 to 2.5 Ω
|
|
||||
| OK | |
| 3. INSPECT SPIRAL CABLE |
Disconnect the steering pad switch and spiral cable connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Spiral Cable Position
Specified condition
a1-8 (EAU) - E18-4 (EAU)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
a1-10 (AU1) - E18-6 (AU1)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
a1-9 (AU2) - E18-5 (AU2)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
- NOTICE:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets below.
- HINT:
- Removal (Click here)
- Installation (Click here)
- Removal (Click here)
|
|
||||
| OK | ||
| ||
