2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Engine Coolant Temperature Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The meter CPU receives engine coolant temperature signals from the ECM via the CAN communication lines (CAN No. 1 Bus). The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E136522E03

INSPECTION PROCEDURE

HINT:
If there is an open or short in the engine coolant temperature sensor circuit, the ECM outputs the DTCs. Perform troubleshooting with the "SFI System" (Click here for 2AZ-FE, Click here for 2GR-FE).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTC is output (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System).

    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System)



B
GO TO CAN COMMUNICATION SYSTEM
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the operation in the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Water Temperature Meter Operation
    Engine coolant temperature receiver gauge
    Low, Normal, High
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


3. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/Min: 0°C (32°F), Max.: 127.5°C (261.5°F)
    After warming up: 78 to 105°C (172 to 221°F) (*1)
    1. If -40°C (-40°F): sensor circuit open
    2. If 140°C (284°F) or more: sensor circuit shorted
    After warming up: 95 to 105°C (203 to 221°F) (*2)
    *1: Except for G.C.C. Countries*2: for G.C.C. Countries

    OK:
    Engine coolant temperature value displayed on the tester is almost the same as needle indication.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


4. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Power train / Engine / Data List.

  1. Check the values by referring to the values in the table below.

    Engine: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Engine coolant temperature: -40°C (-40°F) to 140°C (284°F)
    After warming up:
    80 to 100°C (176 to 212°F)
    1. If -40°C (-40°F): sensor circuit open
    2. If 140°C (284°F) or more: sensor circuit shorted

    OK:
    Engine coolant temperature value displayed on the tester is almost the same as needle indication.



NG
REPLACE ECM
OK


5. REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or a normal one.

    OK:
    The operation of the combination meter assembly returns to normal.



NG
REPLACE ECM
OK

END


← Engine Coolant Temperature Receiver Gauge Malfunction (Jun 2006 – Sep 2006)Engine Coolant Temperature Receiver Gauge Malfunction (from Jun 2009) →