2006-2011 Camry Aurion · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. DISCHARGE FUEL SYSTEM PRESSURE
Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

4. REMOVE FRONT WHEELS

5. REMOVE ENGINE UNDER COVER LH

6. REMOVE ENGINE UNDER COVER RH

7. REMOVE FRONT FENDER APRON SEAL RH

8. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.


9. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

  1. Loosen the radiator drain cock plug and cylinder block drain cock plug, then drain the coolant.

    A136224E04

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


10. DRAIN MANUAL TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


11. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface of the vehicle, wash or remove it completely.


12. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
Click here.

13. REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY

  1. C141972E01
    Remove the 4 bolts, 4 nuts and outer cowl top panel sub-assembly.


14. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Remove the 2 nuts and cover.


15. REMOVE V-RIBBED BELT

  1. A114351E03
    Using SST and a 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then remove the V-ribbed belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply more force than necessary.


16. REMOVE AIR CLEANER INLET ASSEMBLY

  1. A134903
    Remove the 2 bolts, clamp and air cleaner inlet.


17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A144946E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).

  1. A146036
    Disconnect the No. 2 ventilation hose from the air cleaner hose.

  1. A135668
    Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.

  1. A146037
    Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


18. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A134905
    Disconnect the hose clamp.

  1. Remove the 3 bolts and air cleaner case.


19. REMOVE BATTERY

  1. A134906
    Loosen the bolt and nut, and remove the battery clamp.

  1. Remove the battery and battery tray.


20. REMOVE NO. 2 ENGINE MOUNTING STAY RH

  1. A134912
    Remove the 2 bolts and No. 2 engine mounting stay RH.


21. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

  1. A134909
    Remove the bolt and disconnect the ground cable.

  1. A134910
    Remove the 3 bolts and engine moving control rod sub-assembly.


22. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH

  1. A134911
    Remove the 3 bolts and No. 2 engine mounting bracket RH.


23. DISCONNECT NO. 1 VACUUM HOSE CONNECTOR

  1. A134908
    Remove the clamp and disconnect the No. 1 vacuum hose connector.


24. DISCONNECT RADIATOR HOSE INLET

  1. A134907
    Remove the clamp and disconnect the radiator hose inlet.


25. DISCONNECT RADIATOR HOSE OUTLET

  1. A127545
    Remove the clamp and disconnect the radiator hose outlet.


26. DISCONNECT HEATER WATER HOSE INLET

  1. A124832
    Disconnect the heater inlet water hose.


27. DISCONNECT HEATER WATER HOSE OUTLET

  1. A124831
    Disconnect the heater outlet water hose.


28. REMOVE ECM
Click here.

29. DISCONNECT ENGINE WIRE

  1. A132975
    Disconnect the engine wire from the engine room relay block.

    1. Remove the nut and separate the wire harness.

    2. Using a screwdriver, unlock the engine room R/B. Pull the engine room R/B upward.

    3. Disconnect the engine wire connectors.

  1. A134913
    Remove the clamp from the bracket.

  1. A134914
    Remove the 2 bolts and clamp from the body.


30. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C132952
    Remove the 2 clips and 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.


31. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

  1. A060072
    Disconnect the No. 1 oil reservoir to pump hose.


32. DISCONNECT RETURN TUBE SUB-ASSEMBLY

  1. A060073
    Disconnect the return tube sub-assembly.


33. REMOVE CLUTCH ACCUMULATOR ASSEMBLY
Click here.

34. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY
Click here.

35. DISCONNECT FUEL TUBE SUB-ASSEMBLY

  1. A129626
    Remove the No. 1 fuel pipe clamp.

  1. B012941E15
    Disconnect the connector from the tube while pinching parts (A) with your fingers as shown in the illustration.

    NOTICE:
    1. Check for contamination in the tube and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in plastic bags to prevent damage and contamination.


36. REMOVE GENERATOR ASSEMBLY

  1. A135170
    Disconnect the generator connector.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and wire harness clamp bracket.

  1. Remove the wire harness clamp.

  1. A142104
    Remove the 2 bolts and generator assembly.


37. SEPARATE COMPRESSOR AND PULLEY

  1. A134944
    Disconnect the connector.

  1. Remove the 4 bolts and separate the compressor.

    HINT:
    Hang up the hoses instead of detaching them.


38. REMOVE FRONT EXHAUST PIPE ASSEMBLY
Click here.

39. REMOVE FRONT AXLE HUB NUT LH

  1. C108168E02
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


40. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures described for the LH side.


41. REMOVE FRONT STABILIZER LINK ASSEMBLY LH

  1. C144426E02
    Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


42. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


43. REMOVE FRONT SPEED SENSOR LH

  1. C140592
    Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.

  1. C132782E01
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.


44. REMOVE FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.


45. DISCONNECT TIE ROD ASSEMBLY LH
  1. Remove the cotter pin and the nut.

  1. C133488E01
    Using SST, separate the tie rod assembly LH from the steering knuckle.
    SST
    09628-00011  

    NOTICE:
    1. Hang SST with a string, etc. to prevent it from falling.
    2. Do not damage the front disc brake dust cover.
    3. Do not damage the ball joint dust cover.
    4. Do not damage the steering knuckle.


46. DISCONNECT TIE ROD ASSEMBLY RH

47. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM LH

  1. F040142E01
    Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.


48. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures described for the LH side.


49. SEPARATE FRONT AXLE ASSEMBLY LH

  1. D032030E06
    Put matchmarks on the front drive shaft assembly and the axle hub.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.


50. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


51. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C133501
    Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.

  1. C156702E01
    Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.

  1. C156703E01
    Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.


52. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

  1. A059877
    Set the engine lifter.

  1. Remove the 4 bolts, 2 nuts and frame side rail plate sub-assembly RH and LH.

  1. A059878
    Remove the 4 bolts, 2 nuts and front suspension member brace rear RH and LH.

  1. Carefully remove the engine assembly from the vehicle.

  1. A090847E03
    Install the 2 engine hangers as shown in the illustration.
    Part No.:
    Parts
    Part No.
    No. 1 engine hanger
    12281-28010
    No. 2 engine hanger
    12282-28010
    Bolt
    91512-61020

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Using a chain block and an engine sling device, hang the engine assembly.


53. REMOVE VANE PUMP ASSEMBLY

  1. A059879
    Disconnect the oil pressure switch connector.

  1. Loosen the 2 bolts and remove the vane pump from the engine.


54. REMOVE FRONT FRAME ASSEMBLY

  1. A052490
    For automatic transaxle:
    Remove the nut from the engine mounting insulator LH.

  1. A059881
    For manual transaxle:
    Remove the bolt from the engine mounting insulator LH.

  1. A052482
    Remove the nut from the engine mounting insulator RH.

  1. A059880
    Remove the bolt from the engine mounting insulator FR.

  1. A060825
    For manual transaxle:
    Remove the bolt from the engine lateral control rod.

  1. Raise the engine assembly and separate the front frame.


55. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

  1. C083850E02
    Using SST, remove the front drive shaft assembly LH.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    2. Be careful not to drop the drive shaft assembly.


56. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

  1. C080304E03
    Using a screwdriver, remove the bearing bracket hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot and oil seal.


57. REMOVE STARTER ASSEMBLY

  1. A133565
    Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. A133566E01
    Remove the 3 bolts, clutch flexible hose bracket and starter assembly.


58. DISCONNECT WIRE HARNESS
  1. Remove the bolt and separate the ground cable.

  1. Disconnect the back-up light switch connector.

  1. Disconnect the wire harness.


59. REMOVE MANUAL TRANSAXLE ASSEMBLY

  1. D025747
    Remove the 10 bolts.

  1. Separate and remove the transaxle from the engine.


60. REMOVE CLUTCH LINE

  1. C132979
    Remove the 2 bolts, clutch line and bracket.


61. REMOVE WIRE HARNESS CLAMP

  1. C132983
    Remove the 2 bolts and wire harness clamps.


62. REMOVE MANUAL TRANSMISSION CASE PROTECTOR

  1. C132980
    Remove the 2 bolts and manual transmission case protector.


63. REMOVE ENGINE MOUNTING FRONT BRACKET

  1. C132981
    Remove the 3 bolts and engine mounting front bracket.


64. REMOVE ENGINE MOUNTING INSULATOR LH

  1. C132982
    Remove the 4 bolts and engine mounting insulator LH.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →