2006-2011 Camry Aurion · Service Manual BRAKE

C1237/37 Tires of Different Size

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The skid control ECU measures the speed of each wheel by receiving signals from the speed sensor.
These signals are used for recognizing that all 4 wheels are operating properly.
Therefore, all wheel signals must be equal.
DTC No.
DTC Detecting Condition
Trouble Area
C1237/37
When any of the following is detected:
  1. Wheel speed difference between the wheels.
  2. Wheel sensor signal failure.
  3. ABS control continues for 60 sec. or more.
  1. Brake actuator assembly (skid control ECU)
  2. Speed sensor rotor (Front)
  3. Rear axle hub and bearing assembly
  4. Speed sensor
  5. Speed sensor circuit
  6. Tire and wheel size
  7. Tire deformation

WIRING DIAGRAM

C122979E03
F040884E28

INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).


1. CHECK TIRES
  1. Check the size and condition of all 4 wheels (Click here).

    HINT:
    The DTC is output when tire deformation or a difference in tire size is detected.

    OK:
    The diameter of all 4 tires and air pressure are the same.



NG
REPLACE TIRES SO THAT ALL 4 TIRES ARE THE SAME SIZE
OK


2. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS

  1. C136493E15
    Lift up the vehicle.

  1. Disconnect the skid control ECU connector.

  1. Connect the oscilloscope to each speed sensor terminal of the skid control ECU connector.

    Terminals:
    Connector
    Circuit
    A26-5 (FL+) - A26-6 (FL-)
    Front left speed sensor
    A26-10 (FR+) - A26-9 (FR-)
    Front right speed sensor
    A26-7 (RL+) - A26-27 (RL-)
    Rear left speed sensor
    A26-29 (RR+) - A26-8 (RR-)
    Rear right speed sensor

  1. C140980E03
    Check that a waveform is output when the tires are rotated (by the sensor circuit).

    OK:
    A waveform as shown in the figure is output.

    HINT:
    1. Each sensor circuit outputs the same waveform without noise.
    2. As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the fluctuation in the output voltage becomes greater.
    3. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.

  1. Make sure that the waveform does not change while jiggling a connector or a wire harness.

    OK:
    The waveform does not change.

    HINT:
    If the waveform changes while jiggling a connector or a wire harness, there may be a malfunction in the connector or the wire harness.

  1. Connect the connector.



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for 60 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

4. CHECK SPEED SENSOR ROTOR
  1. Check the speed sensor rotor.Front Speed Sensor Rotor (Front drive outboard joint shaft assembly)Rear Speed Sensor Rotor (Rear axle hub and bearing assembly)

    OK:
    No scratches or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after the cleaning/replacement (Click here).



NG
CLEAN OR REPLACE SPEED SENSOR ROTOR
OK


5. CHECK SPEED SENSOR TIP
  1. Remove each speed sensor (Click here for front, Click here for rear).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after the cleaning/replacement (Click here).

  1. Install the speed sensor.



NG
CLEAN OR REPLACE SPEED SENSOR
OK


6. INSPECT SPEED SENSOR

  1. C136027E02
    Disconnect each speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    FRONT:
    Tester Connection
    Condition
    Specified Condition
    A14-1 (FL+) - A14-2 (FL-)
    Always
    0.92 to 1.22 kΩ at 20°C
    A14-1 (FL+) - Body ground
    Always
    10 kΩ or higher
    A14-2 (FL-) - Body ground
    Always
    10 kΩ or higher
    A35-1 (FR+) - A35-2 (FR-)
    Always
    0.92 to 1.22 kΩ at 20°C
    A35-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    A35-2 (FR-) - Body ground
    Always
    10 kΩ or higher
    REAR:
    Tester Connection
    Condition
    Specified Condition
    g1-2 (RL+) - g1-1 (RL-)
    Always
    Below 2.2 kΩ
    g1-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    g1-1 (RL-) - Body ground
    Always
    10 kΩ or higher
    f1-2 (RR+) - f1-1 (RR-)
    Always
    Below 2.2 kΩ
    f1-2 (RR+) - Body ground
    Always
    10 kΩ or higher
    f1-1 (RR-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE EACH SPEED SENSOR
OK


7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU TO EACH SPEED SENSOR)

  1. C139146E03
    Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    FRONT:
    Tester Connection
    Condition
    Specified Condition
    A26-5 (FL+) - A14-1 (FL+)
    Always
    Below 1 Ω
    A26-5 (FL+) - Body ground
    Always
    10 kΩ or higher
    A26-6 (FL-) - A14-2 (FL-)
    Always
    Below 1 Ω
    A26-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    A26-10 (FR+) - A35-1 (FR+)
    Always
    Below 1 Ω
    A26-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    A26-9 (FR-) - A35-2 (FR-)
    Always
    Below 1 Ω
    A26-9 (FR-) - Body ground
    Always
    10 kΩ or higher
    REAR:
    Tester Connection
    Condition
    Specified Condition
    A26-7 (RL+) - g1-2 (RL+)
    Always
    Below 1 Ω
    A26-7 (RL+) - Body ground
    Always
    10 kΩ or higher
    A26-27 (RL-) - g1-1 (RL-)
    Always
    Below 1 Ω
    A26-27 (RL-) - Body ground
    Always
    10 kΩ or higher
    A26-29 (RR+) - f1-2 (RR+)
    Always
    Below 1 Ω
    A26-29 (RR+) - Body ground
    Always
    10 kΩ or higher
    A26-8 (RR-) - f1-1 (RR-)
    Always
    Below 1 Ω
    A26-8 (RR-) - Body ground
    Always
    10 kΩ or higher

  1. Connect the connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU TO EACH SPEED SENSOR)
OK


8. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTC (C1237/37) is not output
    A
    DTC (C1237/37) is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C1231/31 Steering Angle Sensor Circuit Malfunction (from Jun 2009)C1237/37 Tires of Different Size (Oct 2006 – May 2009) →