DIAGNOSTIC TROUBLE CODE CHART
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
- HINT:
- Parameters listed in the chart may be different from your readings depending on the type of instruments used and other factors.
- If any DTCs are displayed during a check mode, check the circuit for the DTCs listed below. For details of each DTC, refer to the page indicated.
- Parameters listed in the chart may be different from your readings depending on the type of instruments used and other factors.
- NOTICE:
- Only when the DTCs below are output from the main body ECU, proceed to the pages listed in the "See page" column. If the DTCs are output from the ECUs other than the main body ECU, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" to determine the malfunctioning part.
- HINT:
- When communication with the ECUs connected to the CAN MS bus is interrupted or a malfunction in the CAN MS bus occurs, the main body ECU detects the malfunctions and outputs DTCs.
| DTC Code |
Detection Item |
Trouble Area |
See page |
| B1207 |
Certification ECU Communication Malfunction |
1. Certification ECU power source circuit 2. Certification ECU 3. Certification ECU main wire or connector |
Click here
|
| B1272 |
Power Seat ECU Communication Stop |
1. Seat position control ECU (Front RH side) power source circuit 2. Seat position control ECU (Front RH side) 3. Seat position control ECU (Front RH side) branch wire or connector |
Click here
|
| B1276 |
Power Mirror Control ECU Communication Stop |
1. Outer mirror control ECU power source circuit 2. Outer mirror control ECU 3. Outer mirror control ECU branch wire or connector |
Click here
|
| B1297 |
Clearance Sonar ECU Communication Stop |
1. Clearance warning ECU power source circuit 2. Clearance warning ECU 3. Clearance warning ECU branch wire or connector |
Click here
|
| B2326 |
CAN MS Bus Line Communication Malfunction |
1. Open or short in CAN MS bus main wire or connector 2. Open or short in CAN MS bus branch wire or connector 3. Certification ECU 4. Seat position control ECU (Front RH side) 5. Outer mirror control ECU 6. Clearance warning ECU 7. Main body ECU 8. CAN No. 3 J/C 9. CAN No. 5 J/C |
Click here
|
- NOTICE:
- Only when the DTCs below are output from the gateway ECU, proceed to the pages listed in the "See page" column. If the DTCs are output from the ECUs other than the gateway ECU, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" to determine the malfunctioning part.
- HINT:
- When communication with the ECUs connected to the CAN No. 2 bus is interrupted or a malfunction in the CAN No. 2 bus occurs, the gateway ECU detects the malfunctions and outputs DTCs.
- If DTC B1201, Mayday ECU Communication Stop Mode, is output, inspect the mayday ECU power source circuit and its CAN branch wire. Refer to the mayday system repair manual for details.
- When communication with the ECUs connected to the CAN No. 2 bus is interrupted or a malfunction in the CAN No. 2 bus occurs, the gateway ECU detects the malfunctions and outputs DTCs.
| DTC Code |
Detection Item |
Trouble Area |
See page |
| U0182 |
Lost Communication with AFS ECU |
1. AFS ECU power source circuit 2. AFS ECU 3. AFS ECU branch wire or connector |
Click here
|
| U1002 |
Lost Communication with Gateway Module |
1. Open or short in CAN No. 2 main bus wire or connector 2. Open or short in CAN No. 2 branch wire or connector 3. CAN No. 2 J/C 4. Gateway ECU 5. AFS ECU |
Click here
|