2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
  1. CAN No. 1 Bus

    1. ECM

    2. Skid control ECU with actuator

    3. Steering angle sensor

    4. Yaw rate sensor

    5. Center airbag sensor

    6. Main body ECU

    7. Air conditioning amplifier

    8. Combination meter ECU

    9. Navigation receiver assembly*1

  2. CAN MS Bus

    1. Clearance warning ECU*2

      HINT:
      *1: w/ Navigation system
      *2: w/ Parking assist-sensor system


BUS CHECK (COMMUNICATION MALFUNCTION DTC)

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.

  1. G029877E01
    Select "Bus Check" from the "System select" screen on the intelligent tester.

  2. G029878
    Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

  3. G029879
    Select the system of the DTC to be checked and select "Details".

  4. G029880
    CAN communication system DTC(s) is/are displayed.


BUS CHECK (COMMUNICATION BUS CHECK)

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.

  1. G029877E01
    Select "Bus Check" from the "System select" screen on the intelligent tester.

  2. G029878
    Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

  3. C128178
    The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

    HINT:
    If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system.

  4. C128179
    "There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
  1. Systems (ECUs, sensors) that use CAN communication vary depending on the vehicle's optional equipment. Check which systems (ECUs, sensors) are installed on the vehicle.

    ECU/Sensor name
    Check method
    ABS/VSC/TRC
    Installed on all vehicles
    Steering Angle Sensor
    Installed on all vehicles
    Yaw Rate/Deceleration Sensor
    Installed on all vehicles
    Engine
    Installed on all vehicles
    ECT
    With automatic transaxle
    SRS Airbag
    Installed on all vehicles
    Air Conditioner
    Installed on all vehicles
    Combination Meter
    Installed on all vehicles
    Main Body
    Installed on all vehicles
    Navigation Receiver Assembly
    w/ Navigation system
    Clearance Sonar
    w/ Parking assist-sensor system


DTC TABLE BY ECU

HINT:
  1. For the CAN communication system, CAN communication system DTCs stored in certain ECUs can be displayed using the intelligent tester.
  2. If CAN communication system DTCs are output, trouble cannot be determined only by the DTCs. Perform troubleshooting according to "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).

  1. ECM (2AZ-FE)

    DTC No.
    Detection Item
    U0101*
    High Speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *: The ECM is malfunctioning if only U0101 is output. Replace the ECM.

  2. ECM (2GR-FE)

    HINT:
    DTC communication uses the CAN communication system.
    DTC No.
    Detection Item
    U0101 (*1)
    Lost Communication with Transfer Case Control Module
    *: If only DTC U0101 is output, refer to the SFI system (Click here)

  3. ECT (2AZ-FE)

    DTC No.
    Detection Item
    U0100*
    High Speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *: The ECM is malfunctioning if only U0100 is output. Replace the ECM.

  4. ECT (2GR-FE)

    DTC No.
    Detection Item
    U0100*
    High speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *: The ECM is malfunctioning if only U0100 is output. Refer to Automatic Transaxle system (Click here).

  5. SKID CONTROL ECU

    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus Off
    U0100
    Lost Communication with ECM/PCM "A"
    U0123
    Lost Communication with Yaw Rate Sensor Module
    U0124
    Lost Communication with Lateral Acceleration Sensor Module
    U0126
    Lost Communication with Steering Angle Sensor Module

    HINT:
    DTC communication uses the CAN communication system.

  6. STEERING ANGLE SENSOR

    HINT:
    The steering angle sensor is connected to the CAN communication system, but CAN communication DTCs are not output.

  7. YAW RATE SENSOR

    HINT:
    The yaw rate sensor is connected to the CAN communication system, but CAN communication DTCs are not output.

  8. CENTER AIRBAG SENSOR

    HINT:
    Although the center airbag sensor is connected to the CAN communication system, CAN communication DTCs are not output.

  9. COMBINATION METER ECU

    DTC No.
    Detection Item
    U0100
    Lost Communication With ECM/PCM "A"
    U0129
    Lost Communication with Brake System Control Mode

    HINT:
    DTC communication is via the CAN communication system.

  10. AIR CONDITIONER AMPLIFIER

    DTC No.
    Detection Item
    B1499
    Multiplex Communication Circuit

    HINT:
    DTC communication is via the CAN communication system.

  11. NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

    DTC No.
    Detection Item
    U0073
    Sending Malfunction (Navigation to APGS)

    HINT:
    DTC communication is via the CAN communication system.

  12. MAIN BODY ECU

    DTC No.
    Detection Item
    B1297
    Clearance Sonar ECU Communication Stop
    B2326
    MS Bus Failure

    HINT:
    DTC communication is via the CAN communication system.

  13. CLEARANCE WARNING ECU (w/ Parking assist-sensor system)

    HINT:
    Although the center airbag sensor is connected to the CAN communication system, CAN communication DTCs are not output.


DTC COMBINATION TABLE
DTC
Trouble Mode
Output from
Output DTC
ECM Communication Stop Mode
Skid Control ECU Communication Stop Mode
Steering Angle Sensor Communication Stop Mode
Skid Control ECU
U0073
X
○*1
X
U0100
○
○*1
X
U0123
X
○*1
X
U0124
X
○*1
X
U0126
X
○*1
○
Combination Meter ECU
U0100
○
X
X
U0129
X
○
X
Navigation ECU
U0073
X
X
X

HINT:
  1. ○: Set
  2. X: Not set or may be set depending on the malfunctioning part when one side of the CAN bus wire becomes open
  3. *1: DTC is not output during communication error.

DTC
Trouble Mode
Output from
Output DTC
Yaw Rate Sensor Communication Stop Mode
Air Conditioning Amplifier Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Skid Control ECU
U0073
X
X
X
U0100
X
X
X
U0123
○
X
X
U0124
○
X
X
U0126
X
X
X
Combination Meter ECU
U0100
X
X
X
U0129
X
X
X
Navigation ECU
U0073
X
X
X

HINT:
  1. ○: Set
  2. X: Not set or may be set depending on the malfunctioning part when one side of the CAN bus wire becomes open

DTC
Trouble Mode
Output from
Output DTC
Main Body ECU Communication Stoop Mode
Combination Meter ECU Communication Stop Mode
Navigation ECU Communication Stop Mode
Skid Control ECU
U0073
X
X
X
U0100
X
X
X
U0123
X
X
X
U0124
X
X
X
U0126
X
X
X
Combination Meter ECU
U0100
X
○*1
X
U0129
X
○*1
X
Navigation ECU
U0073
X
X
○*1

HINT:
  1. ○: Set
  2. X: Not set or may be set depending on the malfunctioning part when one side of the CAN bus wire becomes open
  3. *1: DTC is not output during communication error.

  1. Perform troubleshooting according to the combination of DTCs output.

    HINT:
    1. ECM Communication Stop Mode (Click here)
    2. Skid Control ECU Communication Stop Mode (Click here)
    3. Combination Meter ECU Communication Stop Mode (Click here)
    4. Steering Angle Sensor Communication Stop Mode (Click here)
    5. Yaw Rate Sensor Communication Stop Mode (Click here)
    6. Center Airbag Sensor Communication Stop Mode (Click here)
    7. Air Conditioner Amplifier ECU Communication Stop Mode (Click here)
    8. Main Body ECU Communication Stop Mode (Click here)
    9. Navigation ECU Communication Stop Mode (Click here)

← DIAGNOSIS SYSTEM (Oct 2006 – May 2009)FAIL-SAFE CHART (from Oct 2006) →