Front Brake
Brake
COMPONENTS


REMOVAL
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
1. REMOVE FRONT WHEEL
2. DRAIN BRAKE FLUID
3. REMOVE DISC BRAKE CYLINDER ASSEMBLY

(a) Remove the union bolt and 2 gaskets from the disc brake cylinder assembly, then disconnect the front brake flexible hose.
-

(b) Hold the front disc brake cylinder slide pin and remove the 2 bolts and disc brake cylinder assembly.
-
DISASSEMBLY
1. REMOVE FRONT BRAKE PAD
(a) Remove the 2 brake pads from the front disc brake cylinder mounting.
-
2. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Remove the 2 front disc brake pad support plates.
-
3. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING

(a) Remove the 2 bolts and front disc brake cylinder mounting.
-
4. REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN

(a) Remove the front disc brake cylinder slide pins from the front disc brake cylinder mounting.
-
5. REMOVE FRONT DISC BRAKE BUSHING DUST BOOT

(a) Remove the 2 front disc brake bushing dust boots from the front disc brake cylinder mounting.
-
6. REMOVE FRONT DISC BRAKE PISTON

(a) Prepare a wooden plate to hold the front disc brake pistons.
-
(b) Place the wooden plate between the front disc brake pistons and the disc brake cylinder assembly.
-

(c) Use compressed air to remove the 2 front disc brake pistons from the disc brake cylinder assembly.
CAUTION:
Do not place your fingers in front of the pistons when using compressed air.
NOTICE:
Do not spatter the brake fluid.
-
7. REMOVE CYLINDER BOOT
(a) Remove the 2 cylinder boots from the disc brake cylinder assembly.
-
8. REMOVE PISTON SEAL

(a) Using a screwdriver, remove the 2 piston seals from the disc brake cylinder assembly.
NOTICE:
Do not damage the inner cylinder or cylinder groove.
HINT:
Tape the screwdriver tip before use.
-
9. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP
10. REMOVE FRONT DISC BRAKE BLEEDER PLUG
11. REMOVE FRONT DISC


(a) Remove the front disc.
HINT:
Put matchmarks on the disc and the axle hub.
HINT:
A disc sleeve is fitted to the front disc and is not serviced separately.
NOTICE:
Ensure the disc sleeve is removed with the disc. If it remains on the hub, remove it.
-
INSPECTION
1. INSPECT PAD LINING THICKNESS

(a) Using a ruler, measure the pad lining thickness.
Standard thickness:
9.5 mm (0.37 in.)
Minimum thickness:
2.0 mm (0.078 in.)
If the pad lining thickness is less than the minimum, replace the brake pads.
HINT:
• When replacing the front brake pads with new ones, replace the brake pad support plate at the same time.
• Check wear of the front disc after replacing the brake pads.
-
2. INSPECT BRAKE CYLINDER AND PISTON
(a) Inspect the cylinder bore and piston for rust or scoring. If necessary, replace the front disc brake cylinder assembly and front disc brake piston.
-
3. INSPECT FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Inspect the brake pad support plates. If necessary, replace the brake pad support plate.
HINT:
• When replacing the front brake pads, replace the brake pad support plate at the same time.
• Ensure the pad support plate has sufficient rebound, has no deformation, cracks or wear, and all rust and dirt is cleaned off.
-
4. INSPECT DISC THICKNESS

(b) Using a micrometer, measure the disc thickness.
Standard thickness:
32.0 mm (1.260 in.)
Minimum thickness:
30.0 mm (1.181 in.)
If the disc thickness is less than the minimum, replace the front disc.
-
5. INSPECT DISC RUNOUT

(a) Using SST to hold the front disc, tighten the disc with the 3 hub nuts.
SST
09330-00021
HINT:
Use the SST to hold the disc while torquing the nuts.
Torque:
103 N*m
(1,050 kgf*cm,
76 ft.*lbf)
-

(b) Using a dial indicator, measure the disc runout 10 mm (0.39 in.) away from the outer edge of the disc.
Maximum disc runout:
0.05 mm (0.0020 in.)
NOTICE:
• Keep the magnet of the dial indicator away from the axle hub and speed sensor.
• Install the dial indicator to the shock absorber.
-
(c) If the runout exceeds the maximum value, change the installation positions of the disc and axle so the runout will become minimal. If the runout exceeds the maximum even after the installation positions are changed, check the front axle hub bearing looseness (
Click Here
)
check the front axle hub runout (
Click Here
)
If the hub bearing looseness and runout are normal and if the disc thickness is not within the specified range, grind the disc. If the disc thickness is less than the minimum, replace the disc.
-
(d) Remove the 3 hub nuts.
-
(e) Remove the front disc.
-
REASSEMBLY
1. INSTALL FRONT DISC


(a) Align the matchmarks and install the front disc.
NOTICE:
When replacing the disc with a new one, select the installation position where the front disc has the minimum runout.
-
2. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG
(a) Temporarily tighten the front disc brake bleeder plug to the disc brake cylinder assembly.
-
3. INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP
(a) Install the bleeder plug cap to the front disc brake bleeder plug.
-
4. INSTALL PISTON SEAL
(a) Apply lithium soap base glycol grease to a new piston seal.
-
(b) Install the piston seal to the disc brake cylinder assembly.
-
5. INSTALL CYLINDER BOOT

(a) Apply lithium soap base glycol grease to the piston and a new cylinder boot.
-
(b) Install the cylinder boot to the piston as shown in the illustration.
-
6. INSTALL FRONT DISC BRAKE PISTON
(a) Install the boot securely to the grooves of the cylinder.
-

(b) Push in the piston by hand and install the boot onto the grooves of the piston.
NOTICE:
Install the boot securely to the grooves of the piston.
-
7. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

(a) Apply lithium soap base glycol grease to the seal surface of 2 new front disc brake bushing dust boots.
-
(b) Install the 2 front disc brake bushing dust boots to the front disc brake cylinder slide pin.
-
8. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN
(a) Apply lithium soap base glycol grease to the sliding part and the seal surface of the front disc brake cylinder slide pin.
-

(b) Install the front disc brake cylinder slide pin to the bottom side of the front disc brake cylinder mounting.
-
(c) Install the 2 front disc brake bushing dust boots to the groove of the front disc brake cylinder mounting.
-
9. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

(a) Install the cylinder mounting with the 2 bolts.
Torque:
107 N*m
(1,090 kgf*cm,
79 ft.*lbf)
-
10. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Install the front disc brake pad support plate.
-
11. INSTALL FRONT BRAKE PAD

(a) Install the 2 front brake pads to the front disc brake cylinder mounting.
-
INSTALLATION
1. INSTALL DISC BRAKE CYLINDER ASSEMBLY

(a) Install the disc brake cylinder assembly with 2 new bolts.
Torque:
37 N*m
(377 kgf*cm,
27 ft.*lbf)
-

(b) Connect the front brake flexible hose with the union bolt and 2 new gaskets.
Torque:
35 N*m
(357 kgf*cm,
26 ft.*lbf)
NOTICE:
Install the front brake flexible hose lock securely in the lock hole in the disc brake cylinder assembly.
-
2. FILL RESERVOIR WITH BRAKE FLUID (
Click Here
)
3. BLEED BRAKE LINE (
Click Here
)
4. INSPECT BRAKE FLUID LEVEL IN RESERVOIR (
Click Here
)
5. INSPECT FOR FLUID LEAK
6. INSTALL FRONT WHEEL