ENTRY AND START SYSTEM > Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment |

| 1.CHECK LUGGAGE COMPARTMENT DOOR OPEN FUNCTION |
Check that luggage compartment door open functions can be operated by using the luggage compartment door opener outer switch and electrical key transmitter.
| Result | Proceed to |
| Both luggage compartment door opener outer switch and electrical key transmitter do not operate | A |
| Luggage compartment door opener outer switch does not operate | B |
| Electrical key transmitter does not operate | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY (CANCEL CONDITION) |
![]() |
Check that the luggage compartment door lock cylinder assembly is in the cancel position.
| Result | Proceed to |
| Except cancel position | A |
| Cancel position | B |
|
| ||||
| A | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT DOOR LOCK (MOTOR)) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Trunk and Back-door Open | Luggage compartment door lock motor | ON/OFF | - |
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT DOOR LOCK (COURTESY SWITCH)) |
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Luggage Courtesy SW | Luggage compartment door courtesy light switch signal / ON or OFF | ON: Luggage compartment door open OFF: Luggage compartment door closed | - |
|
| ||||
| OK | |
| 5.INSPECT LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY |
Remove the luggage compartment door lock cylinder assembly .

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 3 | Open position | Below 1 Ω |
| 1 - 3 | Original position | 10 kΩ or higher |
| 2 - 3 | Original position | 10 kΩ or higher |
| 2 - 3 | Cancel position | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - LUGGAGE COMPARTMENT DOOR LOCK CYLINDER) |
![]() |
Disconnect the main body ECU (instrument panel junction block assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E8-2 (TCAN) - S18-2 | Always | Below 1 Ω |
| E8-2 (TCAN) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK CYLINDER - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S18-3 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 8.READ VALUE USING INTELLIGENT TESTER (COURTESY SWITCH) |
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Luggage Courtesy SW | Luggage compartment door courtesy light switch signal / ON or OFF | ON: Luggage compartment door open OFF: Luggage compartment door closed | - |
|
| ||||
| OK | |
| 9.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY (MOTOR) |
![]() |
Remove the luggage compartment door lock assembly (Click here).
Move the door lock to the lock position.
Apply battery voltage to the door lock motor and check the operation of the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 | Unlocks |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - LUGGAGE COMPARTMENT DOOR LOCK) |
![]() |
Disconnect the main body ECU (instrument panel junction block assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E7-1 (TR+) - S5-1 | Always | Below 1 Ω |
| E7-1 (TR+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S5-2 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 12.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY (COURTESY SWITCH) |
![]() |
Remove the luggage compartment door lock assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 - 3 | Unlocked | Below 1 Ω |
| 2 - 3 | Locked | 10 kΩ or higher |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - LUGGAGE COMPARTMENT DOOR LOCK) |
![]() |
Disconnect the main body ECU (instrument panel junction block assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E6-25 (LGCY) - S5-3 | Always | Below 1 Ω |
| E6-25 (LGCY) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 14.READ VALUE USING INTELLIGENT TESTER (TRUNK OPEN MODE) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry & Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Trunk Open Mode | Trunk Open Mode / ON or OFF | Customization status displayed | - |
| Result | Proceed to |
| Entry luggage open function is ON | A |
| Entry luggage open function is OFF | B |
|
| ||||
| A | |
| 15.READ VALUE USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT DOOR OPENER SWITCH) |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Tr/B-Door Unlock SW | Luggage compartment door opener outer switch / ON or OFF | ON: Luggage compartment door opener outer switch is pushed OFF: Luggage compartment door opener outer switch is not pushed | - |
|
| ||||
| OK | |
| 16.CHECK WAVE ENVIRONMENT |
![]() |
Bring the electrical key transmitter near the outside electrical key oscillator (luggage compartment), and perform an entry luggage compartment open function check.
|
| ||||
| OK | ||
| ||
| 17.PERFORM KEY DIAGNOSTIC MODE INSPECTION |
![]() |
Diagnostic mode inspection (outside electrical key oscillator (luggage compartment))
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry & Start / Utility / Communication Check (Key Diag Mode) / Overhead + Luggage (outside).
When the electrical key transmitter is held at the same height as the rear bumper upper surface aligning it with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.
|
| ||||
| OK | ||
| ||
| 18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OUTSIDE ELECTRICAL KEY OSCILLATOR) |
Disconnect the certification ECU (smart key ECU assembly) connector.
![]() |
Disconnect the outside electrical key oscillator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E74-32 (CG8B) - S20-2 (CLGB) | Always | Below 1 Ω |
| E74-31 (CLG8) - S20-1 (CLG5) | Always | Below 1 Ω |
| E74-32 (CG8B) - Body ground | Always | 10 kΩ or higher |
| E74-31 (CLG8) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 19.REPLACE OUTSIDE ELECTRICAL KEY OSCILLATOR (for Luggage Compartment) |
Replace the outside electrical key oscillator (for luggage compartment) (Click here).
| NEXT | |
| 20.CHECK OUTSIDE ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry functions operate normally.
|
| ||||
| OK | ||
| ||
| 21.INSPECT LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH |
Disconnect the luggage compartment door opener outer switch connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 4 - 8 | Luggage compartment door opener outer switch not pushed (OFF) | 10 kΩ or higher |
| 4 - 8 | Luggage compartment door opener outer switch pushed (ON) | Below 1 Ω |
|
| ||||
| OK | |
| 22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - LUGGAGE COMPARTMENT DOOR OPENER SWITCH) |
![]() |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E74-7 (TSW5) - S19-4 | Always | Below 1 Ω |
| E74-7 (TSW5) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 23.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR OPENER SWITCH - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S19-8 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||