Home › TRANSMISSION ยท U660E AUTOMATIC TRANSAXLE › DIFFERENTIAL OIL SEAL

DIFFERENTIAL OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL TRANSAXLE CASE OIL SEAL


    C139870E01
  1. Using SST and a hammer, install a new oil seal to the transaxle case.

    SST
    09316-10010  
    09950-70010   (09951-07100)

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)

  1. Coat the lip of the oil seal with MP grease.



2. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    C139869E01
  1. Using SST and a hammer, install a new oil seal to the transaxle housing.

    SST
    09308-14010  

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)

  1. Coat the lip of the oil seal with MP grease.



3. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    C083851E03
  1. Coat the spline of the inboard joint shaft assembly with ATF.

  1. Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.

    NOTICE:
    1. Set the shaft snap ring with the opening side facing down.
    2. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    3. Move the drive shaft assembly while keeping it level.



4. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH


    C080304E04
  1. Coat the spline of the inboard joint shaft assembly with ATF.

  1. Install the front drive shaft the assembly RH.

  1. Using a screwdriver, install a new bearing bracket hole snap ring.

    NOTICE:
    1. Do not damage the boot and oil seal.
    2. Move the drive shaft assembly while keeping it level.

  1. Install a new bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }



5. INSTALL FRONT AXLE ASSEMBLY LH


    F047689E03
  1. Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.



6. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



7. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM LH


    F040142E03
  1. Install the lower ball joint to the front suspension lower No. 1 arm with the bolt and 2 nuts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }



8. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures described for the LH side.



9. INSTALL TIE ROD ASSEMBLY LH
  1. Install the tie rod end sub-assembly to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut up to 60° further.



10. INSTALL TIE ROD ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



11. INSTALL FRONT SPEED SENSOR LH


    C132782E01
  1. Install the front speed sensor to the steering knuckle with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.



    C140592
  1. Install the flexible hose and the speed sensor to the shock absorber with the bolt and set the sensor clip on the knuckle.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.



12. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.



13. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C140591
  1. Install the stabilizer link assembly with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



14. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



15. INSTALL FRONT AXLE HUB NUT LH
  1. Clean the threaded parts on the drive shaft and front axle hub nut using a non-residue solvent.

    NOTICE:
    Be sure to perform this work for a new drive shaft. Keep the threaded parts free of oil and foreign objects.



    C068609E02
  1. Using a socket wrench (30 mm), install a new axle hub nut.

    Torque:
    294 N*m{ 3,000 kgf*cm , 217 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle hub nut.



16. INSTALL FRONT AXLE HUB NUT RH

HINT:
Use the same procedures described for the LH side.



17. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



18. ADD AUTOMATIC TRANSAXLE FLUID

HINT:
(Click here)



19. ADJUST FRONT WHEEL ALIGNMENT

HINT:
(Click here)



20. CHECK ABS SPEED SENSOR SIGNAL
  1. ABS: (Click here)

  1. VSC: (Click here)