DTC P1603 Engine Stall History |
DTC P1605 Rough Idling |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1603*1 | After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic). |
|
| DTC No. | DTC Detection Condition | Trouble Area |
| P1605 | After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). |
|
| Reference waveforms showing a normal cold engine start |

| Reference waveforms showing a normal warm engine start |

| Reference waveforms showing an engine stop after normal idling |

| Reference values when there is an air leak in the intake system during rough idling |
| Parameter | -3 | -2 | -1 | 0 | 1 | Unit |
| Engine Speed | 644 | 655 | 374 | 371 | 337 | rpm |
| Calculate Load | 23.9 | 24.3 | 29.0 | 30.5 | 33.7 | % |
| Vehicle Load | 12.5 | 12.5 | 37.6 | 36.8 | 15.6 | % |
| MAF | 1.95 | 1.95 | 3.34 | 3.26 | 1.28 | gm/sec |
| Atmosphere Pressure | -0 | -0 | -0 | -0 | -0 | psi(gauge) |
| Coolant Temp | 91 | 91 | 91 | 91 | 91 | °C |
| Intake Air | 49 | 49 | 49 | 49 | 49 | °C |
| Battery Voltage | 13.203 | 13.164 | 12.695 | 12.695 | 12.617 | V |
| Throttle Sensor Volt % | 14.9 | 14.9 | 16.8 | 16.8 | 15.2 | % |
| Throttl Sensor #2 Volt % | 45.8 | 45.8 | 48.2 | 48.2 | 46.2 | % |
| Throttle Sensor Position | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | % |
| Throttle Motor DUTY | 14.9 | 14.9 | 16.8 | 16.8 | 14.9 | % |
| Injector (Port) | 2336 | 2359 | 3566 | 3566 | 3768 | μs |
| Injection Volume (Cylinder 1) | 0.092 | 0.093 | 0.093 | 0.093 | 0.093 | ml |
| Fuel Pump/Speed Status | ON | ON | ON | ON | ON | |
| EVAP (Purge) VSV | 29.0 | 29.4 | 28.2 | 28.2 | 28.6 | % |
| Evap Purge Flow | 9.9 | 9.9 | 9.9 | 9.9 | 9.9 | % |
| Purge Density Learn Value | 1.000 | 1.000 | 1.000 | 1.000 | 1.000 | |
| EVAP purge VSV | OFF | OFF | OFF | OFF | OFF | |
| Target Air-Fuel Ratio | 0.996 | 0.996 | 0.996 | 0.996 | 0.996 | |
| AF Lambda B1S1 | 0.996 | 0.998 | 1.029 | 1.037 | 1.232 | |
| AFS Voltage B1S1 | 3.277 | 3.294 | 3.465 | 3.484 | 4.487 | V |
| O2S B1S2 | 0.835 | 0.835 | 0.835 | 0.835 | 0.835 | V |
| Short FT #1 | 3.906 | 3.906 | 3.125 | 3.125 | 7.812 | % |
| Long FT #1 | -3.125 | -3.125 | -3.125 | -3.125 | -3.125 | % |
| Total FT #1 | 0.011 | 0.011 | 0.011 | 0.011 | 0.011 | |
| Fuel System Status #1 | CL | CL | CL | CL | CL | |
| IGN Advance | 15.0 | 14.5 | 11.0 | 11.0 | 5.5 | deg |
| Knock Feedback Value | -3.0 | -3.0 | -3.0 | -3.0 | -3.0 | CA |
| Knock Correct Learn Value | 18.8 | 18.8 | 18.8 | 18.8 | 18.8 | CA |
| VVT Control Status #1 | ON | ON | ON | ON | ON | |
| Starter Signal | Close | Close | Close | Close | Close |
| Symptom | Suspected Area |
| Engine vibration occurs and engine stops | Air-fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air-fuel ratio abnormal, abnormal combustion |

| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Idling or decelerating | Slowly decreases and engine stalls | Air-fuel ratio abnormal | Air suction |
| 3 to 6 |
| Sensor malfunction (value from sensor too lean) |
| 7 to 16 | |||
| Sensor malfunction (value from sensor too rich) | 25 to 34 | ||||
| Fuel supply problem |
| 17 to 24 | |||
| Intake air volume insufficient | ISC flow rate |
| 35 to 37 | ||
| Excessive valve overlap |
| 38 | |||
| Ignition timing incorrect | Does not operate as expected |
| 39 to 41 | ||
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 42 to 45 | |
| External part malfunctioning | Increase in load |
| 46 to 49 | ||
| Accelerating | - | Crankshaft position sensor, Camshaft position sensor malfunction | Power temporarily cut |
| 1 |
| Mass air flow meter sub-assembly | Foreign matter adhesion |
| 50, 51 | ||
| Fuel supply problem | Fuel leak, clog |
| 54 to 56 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 52, 53 | ||

| Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Slowly decreases and engine stalls | Air-fuel ratio abnormal | Air suction |
| 3 to 6 |
| Sensor malfunction (value from sensor too lean) |
| 7 to 16 | ||
| Sensor malfunction (value from sensor too rich) | 25 to 34 | |||
| Fuel supply problem |
| 17 to 24 | ||
| Intake air volume insufficient | ISC flow rate |
| 35 to 37 | |
| Ignition timing incorrect | Does not operate as expected |
| 39 to 41 | |
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 42 to 45 |
| External part malfunctioning | Increase in load |
| 46 to 49 | |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603 OR P1605) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTCs.
Read the DTCs.
| Result | Proceed to |
| Only DTC P1603 and/or P1605 are output | A |
| DTCs other than P1603 and P1605 are output | B |
|
| ||||
| A | |
| 2.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Problem Symptom | Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | ||
| Closed Throttle Position SW | Engine Speed | Total of Short FT #1 and Long FT #1 | |||
| When idling or decelerating, engine speed slowly decreases and engine stalls | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are +15% or more*2 |
| A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are from -15% to +15% |
| C | |||
| When idling or decelerating, engine speed rapidly decreases and engine stalls | Decreases rapidly*1 | - |
| D | |
| When accelerating or driving at constant speed, engine stalls*4 | At least one is OFF | - | - |
| E |

|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK INTAKE SYSTEM |
Check for air suction in the intake system [vacuum hose disconnection, cracks, gaskets, etc.]
|
| ||||
| OK | |
| 4.CHECK PURGE VSV |
![]() |
Disconnect the purge hose (on the canister side) of the purge VSV.
Start the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
Connect the connector of the purge VSV.
Connect the purge hose of the purge VSV.
|
| ||||
| OK | |
| 5.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Stop Light Switch | At least 1 of the 5 sets of freeze frame data is ON | Air suction from brake booster | A |
| All 5 sets of freeze frame data are OFF | - | B |
|
| ||||
| A | |
| 6.READ VALUE USING INTELLIGENT TESTER (SHORT FT #1) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Short FT #1.
Read value of the Data List items while depressing the brake pedal.
|
| ||||
| OK | |
| 7.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Calculate Load | Below 90% of the current value of the vehicle*1 | Mass air flow meter sub-assembly | A |
| AFS Voltage B1S1 | 3.3 V or higher*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter sub-assembly.
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Install the mass air flow meter sub-assembly.
|
| ||||
| A | ||
| ||
| 9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| Tester Display | Specified Condition |
| Control the Injection Volume for A/F Sensor (25 %) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume for A/F Sensor (-12.5 %) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 10.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR POWER SOURCE) |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C15-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C15-1 (HA1A) - C24-109 (HA1A) | Always | Below 1 Ω |
| C15-3 (A1A+) - C24-112 (A1A+) | Always | Below 1 Ω |
| C15-4 (A1A-) - C24-113 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C15-1 (HA1A) or C24-109 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C15-3 (A1A+) or C24-112 (A1A+) - Body ground | Always | 10 kΩ or higher |
| C15-4 (A1A-) or C24-113 (A1A-) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | ||
| ||
| 12.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Proceed to |
| Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp | Difference in temperature between each item is below 10°C (18°F)*1 | A |
| Difference in temperature between each item is 10°C (18°F) or more*2 | B |
|
| ||||
| A | |
| 13.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 14.INSPECT THERMOSTAT |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 15.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C (248°F) or more | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temperature | Engine coolant temperature is lower than outside temperature by 15°C (27°F) or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 17.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge VSV | A |
| All 5 sets of freeze frame data are 0% | - | B |
|
| ||||
| A | |
| 18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL) |
![]() |
Disconnect the purge hose (on the canister side) of the purge VSV.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
When the purge VSV is operated using the tester, check whether the part of the purge VSV applies suction to your finger.
| Tester Operation | Specified Condition |
| VSV ON | Purge VSV port applies suction to finger |
| VSV OFF | Purge VSV port applies no suction to finger |
| Result | Proceed to |
| NG | A |
| OK | B |
Reconnect the purge VSV connector.
|
| ||||
| A | |
| 19.INSPECT PURGE VSV |
![]() |
Disconnect the purge VSV connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 23 to 26 Ω |
| *1 | Component without harness connected (Purge VSV) |
Reconnect the purge VSV connector.
|
| ||||
| OK | |
| 20.CHECK HARNESS AND CONNECTOR (PURGE VSV POWER SOURCE) |
Disconnect the purge VSV connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C6-1 - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the purge VSV connector.
|
| ||||
| OK | |
| 21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
Disconnect the purge VSV connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C6-2 - C24-49 (PRG) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C6-2 or C24-49 (PRG) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the purge VSV connector.
|
| ||||
| OK | ||
| ||
| 22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.
| Tester Operation | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 23.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | ||
| ||
| 24.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 25.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Calculate Load | 110% or more of the current value of the vehicle*1 | Mass air flow meter sub-assembly | A |
| AFS Voltage B1S1 | Below 3.3 V*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 26.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter sub-assembly.
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
|
| ||||
| A | ||
| ||
| 27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| Tester Display | Specified Condition |
| Control the Injection Volume for A/F Sensor (25%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 28.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR POWER SOURCE) |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C15-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 29.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C15-1 (HA1A) - C24-109 (HA1A) | Always | Below 1 Ω |
| C15-3 (A1A+) - C24-112 (A1A+) | Always | Below 1 Ω |
| C15-4 (A1A-) - C24-113 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C15-1 (HA1A) or C24-109 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C15-3 (A1A+) or C24-112 (A1A+) - Body ground | Always | 10 kΩ or higher |
| C15-4 (A1A-) or C24-113 (A1A-) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | ||
| ||
| 30.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Proceed to |
| Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp | Difference in temperature between each item is below 10°C (18°F)*1 | A |
| Difference in temperature between each item is 10°C (18°F) or more*2 | B |
|
| ||||
| A | |
| 31.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions when the DTC was stored which are recorded in the freeze frame data.

| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 32.INSPECT THERMOSTAT |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 33.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C (248°F) or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temperature | Engine coolant temperature is lower than outside temperature by 15°C (27°F) or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 35.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Total of ISC Learning Value and ISC Feedback Value | Below 80% of the current value of the vehicle*1 | Throttle body assembly | A |
| 120% or more of the current value of the vehicle*2 | B | ||
| From 80 to 120% of the current value of the vehicle | - | C |
|
| ||||
|
| ||||
| A | |
| 36.CHECK THROTTLE BODY ASSEMBLY |
Check for foreign matter and signs that the throttle body assembly was stuck, and also check that the valve and shaft move smoothly during operation.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 37.CHECK THROTTLE BODY ASSEMBLY |
Check if carbon is in the air flow passage of the throttle body.
| Result | Proceed to |
| Carbon in passage | A |
| No carbon in passage | B |
|
| ||||
| A | ||
| ||
| 38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
| Tester Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 39.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10 deg or more | Below 3°CA |
| A |
| 3°CA or more | - | B | |
| Differs from the current value of the vehicle by less than 10 deg | - | - | |
|
| ||||
| A | |
| 40.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
|
| ||||
| OK | |
| 41.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly (Click here).
|
| ||||
| OK | ||
| ||
| 42.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
Disconnect the fuel injector connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C10-1 - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the fuel injector connector.
|
| ||||
| OK | |
| 43.CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE) |
Disconnect the ignition coil connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C11-1 (+B) - C11-4 (GND) | Ignition switch ON | 11 to 14 V |
| C13-1 (+B) - C13-4 (GND) | Ignition switch ON | 11 to 14 V |
| C12-1 (+B) - C12-4 (GND) | Ignition switch ON | 11 to 14 V |
| C14-1 (+B) - C14-4 (GND) | Ignition switch ON | 11 to 14 V |
Reconnect the ignition coil connector.
|
| ||||
| OK | |
| 44.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Idle Spark Advn Ctrl (#1 to #4) | At least one cylinder shows a value of 4°CA or more |
| A |
| All cylinders show a value of less than 4°CA | - | B |
|
| ||||
| A | |
| 45.READ FREEZE FRAME DATA |
Change the location of the ignition coil for the cylinder whose Idle Spark Advn Ctrl (#1 to #4) was 4°CA or more in step 45.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Idle Spark Advn Ctrl (#1 to #4).
| Result | Proceed to |
| Same as result in step 45 | A |
| Different from result in step 45 | B |
|
| ||||
| A | |
| 46.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |
| A/C Signal | Air Conditioner FB Val | ||
| A/C Signal display does not change from OFF*1 | Value displayed for Air Conditioner FB Val does not increase | - | A*2 B*3 |
| A/C Signal display changes from OFF to ON*1 | Value displayed for Air Conditioner FB Val increase | A/C system | C |
|
| ||||
|
| ||||
| A | |
| 47.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | ||
| Electrical Load Feedback Val | Difference between Engine Speed and SPD (NT) | Vehicle Speed | ||
| Value displayed for Electric Load Feedback Val changes | - | - | Electrical load signal circuit | A |
| Value displayed for Electric Load Feedback Val does not change | At least 1 of the 5 sets of freeze frame data is below 100 rpm | Below 30 km/h (19 mph) | A/T system | B |
| 30 km/h (19 mph) or more | - | C | ||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | |
| - | At least 1 of the 5 sets of freeze frame data is below 100 rpm | Below 30 km/h (19 mph) | A/T system | B |
| 30 km/h (19 mph) or more | - | C | ||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | |
|
| ||||
|
| ||||
| A | ||
| ||
| 48.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to |
| Electric Load Feedback Val | ||
| Value displayed for Electric Load Val changes | Electrical load signal circuit | A |
| Value displayed for Electric Load Val does not change | - | B |
| - | - | B |
|
| ||||
| A | ||
| ||
| 49.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |
| Shift SW Status (P Range) or Shift SW Status (N Range) | Neutral Position SW Signal | ||
| At least 1 of the 5 sets of freeze frame data is OFF | In D or R, NSW is ON | Neutral start switch system | A |
| In D or R, NSW is OFF | A/T system | B | |
| All 5 sets of freeze frame data are ON | - | - | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 50.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter sub-assembly | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
|
| ||||
| A | |
| 51.CHECK MASS AIR FLOW METER SUB-ASSEMBLY |
Remove the mass air flow meter sub-assembly.
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Install the mass air flow meter sub-assembly.
|
| ||||
| A | ||
| ||
| 52.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
Disconnect the fuel injector connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C10-1 - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the fuel injector connector.
|
| ||||
| OK | |
| 53.CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE) |
Disconnect the ignition coil connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C11-1 (+B) - C11-4 (GND) | Ignition switch ON | 11 to 14 V |
| C13-1 (+B) - C13-4 (GND) | Ignition switch ON | 11 to 14 V |
| C12-1 (+B) - C12-4 (GND) | Ignition switch ON | 11 to 14 V |
| C14-1 (+B) - C14-4 (GND) | Ignition switch ON | 11 to 14 V |
Reconnect the ignition coil connector.
|
| ||||
| OK | |
| 54.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.
| Tester Operation | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 55.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | ||
| ||
| 56.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 57.REPLACE MALFUNCTIONING PARTS |
If the malfunction could not be identified in steps 3 to 24, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 6 | Brake booster replacement |
| Step 8 | Mass air flow meter sub-assembly replacement |
| Step 9 | Air fuel ratio sensor replacement |
| Step 16 | Engine coolant temperature sensor replacement |
| Step 18 | Purge VSV replacement |
| Step 24 | Fuel pump replacement |
If the malfunction could not be identified in steps 25 to 34, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 26 | Mass air flow meter sub-assembly replacement |
| Step 27 | Air fuel ratio sensor replacement |
| Step 34 | Engine coolant temperature sensor replacement |
If the malfunction could not be identified in steps 35 to 41, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 36, 37 | Throttle body assembly replacement |
| Step 39 | Knock control sensor replacement |
If the malfunction could not be identified in steps 42 to 49, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 46 | A/C system inspection and repair |
| Step 47 | Electrical load system inspection and repair A/T system inspection or repair |
| Step 49 | Park/neutral position switch assembly replacement |
If the malfunction could not be identified in steps 50 to 56, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 51 | Mass air flow meter sub-assembly replacement |
| NEXT | |
| 58.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
| NEXT | |
| 59.PERFORM CONFIRMATION DRIVING PATTERN |
Check if engine stall symptoms are present.
|
| ||||
| OK | ||
| ||