DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
DTC P0174 System Too Lean (Bank 2) |
DTC P0175 System Too Rich (Bank 2) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0171 P0174 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|
| P0172 P0175 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic) |
|
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0171, P0172, P0174 or P0175 | A |
| P0171, P0172, P0174 or P0175 and other DTCs | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
|
| ||||
| OK | |
| 3.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
Select the following menu items on the tester: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Status AFS B1S1 or AFS B2S1 | Status O2S B1S2 or O2S B2S2 | A/F Condition and A/F Sensor Condition | Misfires | Suspected Trouble Areas | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - | - | C |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich | Rich | Actual air-fuel ratio rich | - |
| A |
| Lean | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
| Rich | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine / Data List / Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 8.CHECK FOR EXHAUST GAS LEAKS |
|
| ||||
| OK | |
| 9.CHECK FOR SPARKS AND IGNITION |
Check for sparks and ignition (Click here).
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Inspect the fuel injector assembly (Click here).
|
| ||||
| OK | |
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connection | Specified Condition |
| HA1A (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA2A (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HA2A (1) - A2A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 12.INSPECT ENGINE ROOM JUNCTION BLOCK (A/F SENSOR HEATER RELAY) |
![]() |
Remove the engine room junction block from the engine room R/B.
Measure the A/F relay resistance.
| Tester Connection | Specified Condition |
| 1G-1 - 1A-4 | 10 kΩ or higher |
| 1G-1 - 1A-4 | Below 1 Ω (when battery voltage applied to terminals 1E-6 and 1E-11) |
Reinstall the engine room junction block.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (C15-2) - Body ground | 9 to 14 V |
| +B (C35-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| HA1A (C15-1) - HA1A (C58-86) | Below 1 Ω |
| A1A+ (C15-3) - A1A+ (C58-93) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C58-116) | Below 1 Ω |
| HA2A (C35-1) - HA2A (C58-109) | Below 1 Ω |
| A2A+ (C35-3) - A2A+ (C58-120) | Below 1 Ω |
| A2A- (C35-4) - A2A- (C58-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C15-1) - HA1A (C55-86) | Below 1 Ω |
| A1A+ (C15-3) - A1A+ (C55-93) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C55-116) | Below 1 Ω |
| HA2A (C35-1) - HA2A (C55-109) | Below 1 Ω |
| A2A+ (C35-3) - A2A+ (C55-120) | Below 1 Ω |
| A2A- (C35-4) - A2A- (C55-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C58-86) - Body ground | 10 kΩ or higher |
| A1A+ (C15-3) or A1A+ (C58-93) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C58-116) - Body ground | 10 kΩ or higher |
| HA2A (C35-1) or HA2A (C58-109) - Body ground | 10 kΩ or higher |
| A2A+ (C35-3) or A2A+ (C58-120) - Body ground | 10 kΩ or higher |
| A2A- (C35-4) or A2A- (C58-119) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C55-86) - Body ground | 10 kΩ or higher |
| A1A+ (C15-3) or A1A+ (C55-93) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C55-116) - Body ground | 10 kΩ or higher |
| HA2A (C35-1) or HA2A (C55-109) - Body ground | 10 kΩ or higher |
| A2A+ (C35-3) or A2A+ (C55-120) - Body ground | 10 kΩ or higher |
| A2A- (C35-4) or A2A- (C55-119) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3 (Procedure A).
Turn the ignition switch to the ON position and turn the tester on (Procedure B).
Clear the DTCs (Click here) (Procedure C).
Select the check mode using the tester (Click here) (Procedure D).
Start the engine and warm it up with all the accessories switched off (Procedure E).
Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1,400 rpm and 3,200 rpm for 3 to 5 minutes (Procedure F).

| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175) |
Select the following menu items: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0171, P0172, P0174 or P0175 | B |
|
| ||||
| A | ||
| ||