ENTRY AND START SYSTEM > Front Passenger Side Door Entry Unlock Function does not Operate |

| 1.CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| P-Door Lock Pos SW | Front passenger side door lock position switch signal/ON or OFF | ON: Front passenger side door is unlocked OFF: Front passenger side door is locked | - |
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (DOOR OUTSIDE HANDLE) |
Enter the following menus: Body / Entry & Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| P-Door Touch Sensor | Front passenger side door touch sensor / ON or OFF | ON: Touch sensor is touched OFF: Touch sensor is not touched | - |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the certification ECU (smart key ECU assembly) connector.
![]() |
Disconnect the door electrical key oscillator (for front passenger side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E74-6 (SEL2) - W2-4 (SEL) | Always | Below 1 Ω |
| E74-23 (SEN2) - W2-6 (SENS) | Always | Below 1 Ω |
| E74-6 (SEL2) - Body ground | Always | 10 kΩ or higher |
| E74-23 (SEN2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| E74-6 (SEL2) - X2-4 (SEL) | Always | Below 1 Ω |
| E74-23 (SEN2) - X2-6 (SENS) | Always | Below 1 Ω |
| E74-6 (SEL2) - Body ground | Always | 10 kΩ or higher |
| E74-23 (SEN2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE) |
![]() |
Disconnect the front door outside handle assembly (for front passenger side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-6 (SGT) - W2-2 (SGT) | Always | Below 1 Ω |
| W1-6 (SGT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| X1-6 (SGT) - X2-2 (SGT) | Always | Below 1 Ω |
| X1-6 (SGT) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.REPLACE DOOR ELECTRICAL KEY OSCILLATOR (for Front Passenger Side) |
Replace the door electrical key oscillator (for front passenger side) (Click here).
| NEXT | |
| 7.CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Front Passenger Side) |
Check that the entry functions operate normally (Click here).
|
| ||||
| OK | ||
| ||
| 8.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side) |
Replace the front door outside handle assembly (for front passenger side) (Click here).
| NEXT | |
| 9.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side) |
Check that the entry functions operate normally (Click here).
|
| ||||
| OK | ||
| ||