Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

DTC    C1AEC    Front Sensor Communication Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the front sensors and the ECU, or when there is a malfunction in a front sensor.

DTC No.
DTC Detection Condition
Trouble Area
C1AEC
An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the ignition switch is turned to ON.
  1. Front ultrasonic sensor circuit
  2. Clearance warning ECU

WIRING DIAGRAM


E149953E09


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (C1AEC)
  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AEC is output
    A
    No DTC is output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - FRONT LEFT SENSOR)


    E149962E15
  1. Disconnect the O28 connector from the clearance warning ECU.

  1. Disconnect the A59 connector from the No. 1 ultrasonic sensor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O28-21 (BOF) - A59-1 (BI)
    Always
    Below 1 Ω
    O28-9 (SOF) - A59-3 (SI)
    O28-19 (E1) - A59-5 (EI)
    O28-21 (BOF) - Body ground
    10 kΩ or higher
    O28-9 (SOF) - Body ground
    O28-19 (E1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (FRONT LEFT SENSOR - FRONT RIGHT SENSOR)


    E149959E24
  1. Disconnect the A60 and A59 connectors from the No. 1 ultrasonic sensors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A59-2 (BO) - A60-1 (BI)
    Always
    Below 1 Ω
    A59-4 (SO) - A60-3 (SI)
    A59-6 (EO) - A60-5 (EI)
    A59-2 (BO) - Body ground
    10 kΩ or higher
    A59-4 (SO) - Body ground
    A59-6 (EO) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK NO. 1 ULTRASONIC SENSOR (FRONT LEFT SENSOR)
  1. Remove the No. 1 ultrasonic sensor (front left sensor) (Click here).



    E163604E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (BI) - 5 (EI)
    Always
    10 kΩ or higher
    1 (BI) - 2 (BO)
    Always
    10 kΩ or higher
    3 (SI) - 4 (SO)
    Always
    Below 1 Ω
    5 (EI) - 6 (EO)
    Always
    Below 1 Ω



NG
REPLACE NO. 1 ULTRASONIC SENSOR (FRONT LEFT SENSOR) (Click here)
OK


5.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT LEFT SENSOR)


    E149965E09
  1. Replace the No. 1 ultrasonic sensor (front left sensor) with a normally functioning sensor (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


6.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AEC is output
    A
    No DTC is output
    B



B
END (FRONT LEFT SENSOR WAS DEFECTIVE)
A


7.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT RIGHT SENSOR)


    E149965E10
  1. Replace the No. 1 ultrasonic sensor (front right sensor) with a normally functioning sensor (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


8.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AEC is output
    A
    No DTC is output
    B



B
END (FRONT RIGHT SENSOR WAS DEFECTIVE)
A

REPLACE CLEARANCE WARNING ECU (Click here)