Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

DTC    C1AED    Rear Sensor Communication Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor.

DTC No.
DTC Detection Condition
Trouble Area
C1AED
An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the ignition switch is turned to ON.
  1. Rear ultrasonic sensor circuit
  2. Clearance warning ECU

WIRING DIAGRAM


E149954E05


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (C1AED)
  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AED is output
    A
    No DTC is output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - REAR RIGHT SENSOR)


    E149962E16
  1. Disconnect the O28connector from the clearance warning ECU.

  1. Disconnect the k1 connector from the No. 1 ultrasonic sensor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O28-7 (BOR) - k1-1 (BI)
    Always
    Below 1 Ω
    O28-24 (SOR) - k1-3 (SI)
    O28-18 (E2) - k1-5 (EI)
    O28-7 (BOR) - Body ground
    10 kΩ or higher
    O28-24 (SOR) - Body ground
    O28-18 (E2) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (REAR RIGHT SENSOR - REAR RIGHT CENTER SENSOR)


    E149959E25
  1. Disconnect the k1 and k2 connectors from the No. 1 ultrasonic sensors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    k1-2 (BO) - k2-1 (BI)
    Always
    Below 1 Ω
    k1-4 (SO) - k2-3 (SI)
    k1-6 (EO) - k2-5 (EI)
    k1-2 (BO) - Body ground
    10 kΩ or higher
    k1-4 (SO) - Body ground
    k1-6 (EO) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR RIGHT CENTER SENSOR - REAR LEFT CENTER SENSOR)


    E149959E26
  1. Disconnect the k2 and k3 connectors from the No. 1 ultrasonic sensors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    k2-2 (BO) - k3-1 (BI)
    Always
    Below 1 Ω
    k2-4 (SO) - k3-3 (SI)
    k2-6 (EO) - k3-5 (EI)
    k2-2 (BO) - Body ground
    10 kΩ or higher
    k2-4 (SO) - Body ground
    k2-6 (EO) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (REAR LEFT CENTER SENSOR - REAR LEFT SENSOR)


    E149959E27
  1. Disconnect the k3 and k4 connectors from the No. 1 ultrasonic sensors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    k3-2 (BO) - k4-1 (BI)
    Always
    Below 1 Ω
    k3-4 (SO) - k4-3 (SI)
    k3-6 (EO) - k4-5 (EI)
    k3-2 (BO) - Body ground
    10 kΩ or higher
    k3-4 (SO) - Body ground
    k3-6 (EO) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK NO. 1 ULTRASONIC SENSOR (REAR RIGHT SENSOR)
  1. Remove the No. 1 ultrasonic sensor (rear right sensor) (Click here).



    E163604E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (BI) - 5 (EI)
    Always
    10 kΩ or higher
    1 (BI) - 2 (BO)
    Always
    10 kΩ or higher
    3 (SI) - 4 (SO)
    Always
    Below 1 Ω
    5 (EI) - 6 (EO)
    Always
    Below 1 Ω



NG
REPLACE NO. 1 ULTRASONIC SENSOR (REAR RIGHT SENSOR) (Click here)
OK


7.CHECK NO. 1 ULTRASONIC SENSOR (REAR RIGHT CENTER SENSOR)
  1. Remove the No. 1 ultrasonic sensor (rear right center sensor) (Click here).



    E163604E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (BI) - 5 (EI)
    Always
    10 kΩ or higher
    1 (BI) - 2 (BO)
    Always
    10 kΩ or higher
    3 (SI) - 4 (SO)
    Always
    Below 1 Ω
    5 (EI) - 6 (EO)
    Always
    Below 1 Ω



NG
REPLACE NO. 1 ULTRASONIC SENSOR (REAR RIGHT CENTER SENSOR) (Click here)
OK


8.CHECK NO. 1 ULTRASONIC SENSOR (REAR LEFT CENTER SENSOR)
  1. Remove the No. 1 ultrasonic sensor (rear left center sensor) (Click here).



    E163604E23
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (BI) - 5 (EI)
    Always
    10 kΩ or higher
    1 (BI) - 2 (BO)
    Always
    10 kΩ or higher
    3 (SI) - 4 (SO)
    Always
    Below 1 Ω
    5 (EI) - 6 (EO)
    Always
    Below 1 Ω



NG
REPLACE NO. 1 ULTRASONIC SENSOR (REAR LEFT CENTER SENSOR) (Click here)
OK


9.REPLACE NO. 1 ULTRASONIC SENSOR (REAR RIGHT SENSOR)


    E149965E11
  1. Replace the No. 1 ultrasonic sensor (rear left sensor) with a normally functioning sensor (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


10.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AED is output
    A
    No DTC is output
    B



B
END (REAR RIGHT SENSOR WAS DEFECTIVE)
A


11.REPLACE NO. 1 ULTRASONIC SENSOR (REAR RIGHT CENTER SENSOR)


    E149965E08
  1. Replace the No. 1 ultrasonic sensor (rear left center sensor) with a normally functioning sensor (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


12.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AED is output
    A
    No DTC is output
    B



B
END (REAR RIGHT CENTER SENSOR WAS DEFECTIVE)
A


13.REPLACE NO. 1 ULTRASONIC SENSOR (REAR LEFT CENTER SENSOR)


    E149965E12
  1. Replace the No. 1 ultrasonic sensor (rear right center sensor) with a normally functioning sensor (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


14.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AED is output
    A
    No DTC is output
    B



B
END (REAR LEFT CENTER SENSOR WAS DEFECTIVE)
A


15.REPLACE NO. 1 ULTRASONIC SENSOR (REAR LEFT SENSOR)


    E149965E13
  1. Replace the No. 1 ultrasonic sensor (rear right sensor) with a normally functioning sensor (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


16.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AED is output
    A
    No DTC is output
    B



B
END (REAR LEFT SENSOR WAS DEFECTIVE)
A

REPLACE CLEARANCE WARNING ECU (Click here)