Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

DTC    C1622    Open or Short Circuit in Back Camera Signal

for Preparation Click here


DESCRIPTION

This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.

DTC No.
DTC Detection Condition
Trouble Area
C1622
Open or Short Circuit in Back Camera Signal
  1. Harness and connector
  2. Navigation receiver assembly
  3. Rear television camera assembly
  4. Luggage compartment door opener outer switch*1
  1. *1: w/ Entry and Start System

WIRING DIAGRAM


w/o Entry and Start System

E183755E07


w/ Entry and Start System

E183754E03


INSPECTION PROCEDURE

1.CONFIRM MODEL
  1. Chose the model to be inspected.

    Result:
    Result
    Proceed to
    w/o Entry and Start System
    A
    w/ Entry and Start System
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - REAR TELEVISION CAMERA)


    E183802E01
  1. Disconnect the F24 connector from the navigation receiver assembly and the S19 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S19-6 (CV+) - F24-1 (V+)
    Always
    Below 1 Ω
    S19-5 (CB+) - F24-2 (CA+)
    Always
    Below 1 Ω
    S19-1 (CGND) - F24-12 (CGND)
    Always
    Below 1 Ω
    S19-2 (CV-) - F24-11 (V-)
    Always
    Below 1 Ω
    S19-6 (CV+) - Body ground
    Always
    10 kΩ or higher
    S19-5 (CB+) - Body ground
    Always
    10 kΩ or higher
    S19-1 (CGND) - Body ground
    Always
    10 kΩ or higher
    S19-2 (CV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER - REAR TELEVISION CAMERA)
OK


3.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Reconnect the S19 connector to the rear television camera assembly.



    E185299E03
  1. Reconnect the F24 connector to the navigation receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-11 (V-) - Body ground
    Always
    Below 1 Ω
    F24-12 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F24-2 (CA+) - F24-12 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7 V

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4.INSPECT REAR TELEVISION CAMERA ASSEMBLY


    E183803E01
  1. Check that the F27 and F24 connectors are connected to the navigation receiver assembly.



    E171712E02
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F24-1 (V+) - F27-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (to Navigation Receiver Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - LUGGAGE COMPARTMENT DOOR OPENER SWITCH)


    E183802E01
  1. Disconnect the F24 connector from the navigation receiver assembly and the S19 connector from the luggage compartment door opener outer switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S19-6 (CV+) - F24-1 (V+)
    Always
    Below 1 Ω
    S19-5 (CB+) - F24-2 (CA+)
    Always
    Below 1 Ω
    S19-1 (CGND) - F24-12 (CGND)
    Always
    Below 1 Ω
    S19-2 (CV-) - F24-11 (V-)
    Always
    Below 1 Ω
    S19-6 (CV+) - Body ground
    Always
    10 kΩ or higher
    S19-5 (CB+) - Body ground
    Always
    10 kΩ or higher
    S19-1 (CGND) - Body ground
    Always
    10 kΩ or higher
    S19-2 (CV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Luggage Compartment Door Opener Outer Switch)



NG
REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER - LUGGAGE COMPARTMENT DOOR OPENER SWITCH)
OK


6.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Reconnect the S19 connector to the luggage compartment door opener outer switch.



    E185299E03
  1. Reconnect the F24 connector to the navigation receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-11 (V-) - Body ground
    Always
    Below 1 Ω
    F24-12 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F24-2 (CA+) - F24-12 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7 V

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


7.INSPECT REAR TELEVISION CAMERA ASSEMBLY


    E183803E01
  1. Check that the F27 and F24 connectors are connected to the navigation receiver assembly.



    E171712E02
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F24-1 (V+) - F27-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (to Navigation Receiver Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
Go to step 8
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

8.REPLACE LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH
  1. Replace the luggage compartment door opener outer switch with a new or normally functioning one (Click here).


NEXT


9.CHECK DTC OUTPUT (C1622)
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1622 is not output
    A
    DTC C1622 is output
    B



B
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
A

END