Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CAMSHAFT › 2011.10–2015.04
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073927 CAMSHAFT A

2AR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11821 1.INSTALL NO. 2 CAMSHAFT BEARING

Hide 11811 2.INSTALL NO. 1 CAMSHAFT BEARING

Hide 15678A 3.INSTALL OIL CONTROL VALVE FILTER

Hide 13070A 4.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A196902C21
1.896,0.656 1.771,0.656 1.771,0.656 1.594,0.927 false 1.229,0.177 1.104,0.177 1.104,0.177 0.667,0.802 false 2,0.573 2.167,0.74 0.167,0.167 10 false *2 1.281,0.115 1.594,0.313 0.313,0.198 10 false *1
*1 Knock Pin Hole
*2 Knock Pin


Align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear assembly.


b.
A196904C56
2.167,0.854 1.917,0.854 1.917,0.854 1.5,1.083 false 0.823,0.75 0.917,0.75 0.917,0.75 1.146,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Flange
*a INCORRECT
*b CORRECT
*c Clearance
*d No Clearance


Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.


c.
A250991

Fix the camshaft timing exhaust gear assembly with the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Do not disassemble the camshaft timing exhaust gear.


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 5.SET TDC/COMPRESSION

a.
A252819C08
1.802,0.771 2.969,1.5 true 2.99,1.458 3.167,1.625 0.177,0.167 10 false *a
*a Timing Notch


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.


Hide 13512 6.INSTALL NO. 2 CAMSHAFT

a.
A196911C30
1.073,0.229 1.24,0.229 1.24,0.229 1.563,0.542 false 2.854,1.042 2.531,1.042 false 0.729,1.125 1.063,1.125 true 2.906,0.958 3.104,1.281 0.198,0.323 10 false *2 0.865,0.146 1.042,0.323 0.177,0.177 10 false *1 0.552,1.042 0.75,1.375 0.198,0.333 10 false *3
*1 Valve Rocker Arm
*2 Valve Lash Adjuster
*3 Valve Stem Cap


Make sure that the valve rocker arms are installed as shown in the illustration.


b.

Clean the camshaft journals.


c.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


d.
A250992C07
2.26,3.354 2.802,3.281 true 2.156,3.604 2.646,3.865 true 2.875,3.188 3.063,3.354 0.188,0.167 10 false *a 2.698,3.802 2.885,3.969 0.188,0.167 10 false *b
*a Paint Mark
*b Timing mark


Hold up the chain and align the timing mark and the paint mark, and install the camshaft.

HINT:

Perform "Inspection After Repair" after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13511 7.INSTALL CAMSHAFT

a.
A196911C30
1.073,0.229 1.24,0.229 1.24,0.229 1.563,0.542 false 2.854,1.042 2.531,1.042 false 0.729,1.125 1.063,1.125 true 2.906,0.958 3.104,1.281 0.198,0.323 10 false *2 0.865,0.146 1.042,0.323 0.177,0.177 10 false *1 0.552,1.042 0.75,1.375 0.198,0.333 10 false *3
*1 Valve Rocker Arm
*2 Valve Lash Adjuster
*3 Valve Stem Cap


Make sure that the valve rocker arms are installed as shown in the illustration.


b.

Clean the camshaft journals.


c.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


d.
A251007C07
1.042,2.677 0.688,2.573 false 1.167,2.167 1.354,2.333 0.188,0.167 10 *a 0.5,2.479 0.688,2.646 0.188,0.167 10 *1
*1 Knock Pin
*a Approximately 17°


Install the camshaft to the camshaft housing as shown in the illustration.

HINT:

Perform "Inspection After Repair" after replacing the camshaft.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 8.INSTALL CAMSHAFT BEARING CAP

a.
A250994

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


b.
A284106N11
1.729,0.333 1.885,0.531 0.156,0.198 10 1 1.74,1.771 1.896,1.969 0.156,0.198 10 2 2.313,0.344 2.469,0.542 0.156,0.198 10 3 2.354,1.792 2.51,1.99 0.156,0.198 10 4 1.156,0.344 1.313,0.542 0.156,0.198 10 5 1.135,1.792 1.292,1.99 0.156,0.198 10 6 2.885,0.344 3.042,0.542 0.156,0.198 10 7 2.948,1.781 3.104,1.979 0.156,0.198 10 8 0.594,0.313 0.75,0.51 0.156,0.198 10 9 0.521,1.938 0.833,2.135 0.313,0.198 10 10

Using several steps, uniformly tighten the 10 bolts in the sequence shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


c.
A284105N10
1.729,1.542 1.885,1.74 0.156,0.198 10 1 1.74,0.021 1.896,0.219 0.156,0.198 10 2 2.333,1.531 2.49,1.729 0.156,0.198 10 3 2.281,0.021 2.438,0.219 0.156,0.198 10 4 1.146,1.531 1.302,1.729 0.156,0.198 10 5 1.167,0.031 1.323,0.229 0.156,0.198 10 6 2.927,1.531 3.083,1.729 0.156,0.198 10 7 2.833,0.031 2.99,0.229 0.156,0.198 10 8 0.167,1.125 0.323,1.323 0.156,0.198 10 9 0.573,0 0.885,0.198 0.313,0.198 10 10 0.521,1.813 0.833,2.01 0.313,0.198 10 11

Using several steps, uniformly tighten the 11 bolts in the sequence shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


d.

Check the torque of each bolt again.


Hide 13050 9.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A284096C17
0.865,1.729 1.021,1.729 1.021,1.729 1.781,1.333 false 0.771,3.969 0.927,3.969 0.927,3.969 1.688,3.573 false 2.042,1.604 2.458,1.948 2.458,1.948 2.615,1.948 false 2.073,3.677 2.438,3.417 2.438,3.417 2.583,3.417 false 0.083,0.25 0.396,0.406 0.313,0.156 10 false *a 0.083,2.583 0.396,2.74 0.313,0.156 10 false *b 0.708,1.625 1.021,1.781 0.313,0.156 10 false *1 2.667,1.844 2.979,2 0.313,0.156 10 false *c 2.635,3.323 2.948,3.479 0.313,0.156 10 false *c 0.604,3.854 0.917,4.01 0.313,0.156 10 false *1
*1 Knock Pin Hole
*a Advanced Position
*b Retarded Position
*c Alignment Mark


Check the camshaft timing gear position.

NOTICE:
·

If the camshaft timing gear is set to the advanced position, do not let the camshaft timing gear rotate clockwise during installation.

·

If the camshaft timing gear has rotated to the most retarded position, make sure to release the lock pin and set the camshaft timing gear to the most advanced position before tightening the camshaft timing gear.




b.
A251004C07
2.043,2.092 2.214,2.252 0.171,0.16 10 *a 2.109,3.019 2.28,3.178 0.171,0.16 10 *b
*a Narrow
*b Wide


Install the camshaft timing gear as shown in the illustration.


c.
A250998C07
1.164,2.02 1.352,2.184 0.188,0.164 10 *a 2.678,2.974 2.866,3.138 0.188,0.164 10 *a 1.216,2.951 1.404,3.115 0.188,0.164 10 *b 2.74,2.034 2.928,2.198 0.188,0.164 10 *b
*a Narrow
*b Wide


Turn the camshaft timing gear approximately 180° counterclockwise.


d.
A250999C07
1.375,0.74 0.563,0.313 true 1.354,1 0.271,1 true 0.365,0.188 0.604,0.354 0.24,0.167 10 false *a 0.104,0.896 0.375,1.063 0.271,0.167 10 false *b
*a Paint Mark
*b Timing mark


Align the paint mark with the timing mark to install the chain.


e.
A196901C36
1.979,0.625 1.854,0.625 1.854,0.625 1.635,0.906 false 1.25,0.208 1.125,0.208 1.125,0.208 0.698,0.771 false 1.292,0.115 1.5,0.323 0.208,0.208 10 false *1 2.021,0.542 2.281,0.729 0.26,0.188 10 false *2
*1 Knock Pin Hole
*2 Knock Pin


Align and attach the knock pin of the camshaft with the pin hole of the camshaft timing gear.


f.
A196904C56
2.167,0.854 1.917,0.854 1.917,0.854 1.5,1.083 false 0.823,0.75 0.917,0.75 0.917,0.75 1.146,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a INCORRECT
*b CORRECT
*c Clearance
*d No Clearance


Check that there is no clearance between the camshaft timing gear and camshaft flange.


g.

Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



h.

If the lock pin has not been released, release it.

i.
A249942C07
1.063,0.979 0.458,0.635 false 0.375,0.969 1.115,1.125 false 0.26,0.521 0.438,0.688 0.177,0.167 10 *b 0.208,0.854 0.385,1.021 0.177,0.167 10 *a
*a Make a Hole
*b Adhesive Tape Sealing Area


After cleaning and degreasing the intake side VVT oil hole on the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



ii.

Make a hole in the adhesive tape covering the oil hole as shown in the illustration. (Procedure A)


iii.
A251001

Apply approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the hole made in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach the adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.




iv.

Forcibly turn the camshaft timing gear in the advance direction (counterclockwise).

HINT:

Depending on the air pressure applied, the camshaft timing gear may turn in the advance direction without assistance by hand.



v.

Remove the adhesive tape from the No. 1 camshaft bearing cap.



i.
A249935

Using a wrench to hold the hexagonal portion of the camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Be careful not to damage the cylinder head or spark plug tube with the wrench.



j.
A252822C06
1,0.906 1.865,0.167 1.865,0.167 2.896,0.927 true 1.01,1.104 1.865,1.646 1.865,1.646 2.938,1.146 true 1.792,0 1.979,0.188 0.188,0.188 10 false *a 1.792,1.667 1.979,1.854 0.188,0.188 10 false *b
*a Paint Mark
*b Timing mark


Check that each timing mark of the camshaft timing gear and camshaft timing exhaust gear are aligned with each matchmark located as shown in the illustration.

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13540 12.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A245327N15
1.958,0.198 2.229,0.375 0.271,0.177 10 10°

Turn the crankshaft approximately 10° clockwise.


b.
A249933

Install a new gasket and the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure not to drop the gasket inside the timing chain cover.



c.

Remove the pin from the stopper plate.


Hide 13.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.

A292248C06
5.031,1.167 6.135,1.656 false 0.396,1.76 1.167,2.094 false 2.677,2.125 3.344,1.792 false 0.281,2.188 1.573,2.271 false 2.823,2.531 3.49,2.198 false 0.219,1.656 0.531,1.813 0.313,0.156 10 false *a 6.188,1.594 6.438,1.792 0.25,0.198 10 false *b 1.25,0.052 1.563,0.208 0.313,0.156 10 false *c 2.448,0.115 2.76,0.271 0.313,0.156 10 false *d 3.396,1.688 3.708,1.844 0.313,0.156 10 false *a 0.146,2.094 0.302,2.292 0.156,0.198 10 false A 3.552,2.083 3.708,2.281 0.156,0.198 10 false A
*a Timing Mark *b Timing Notch
*c Approximately 7° *d Approximately 32°



b.

Check that the timing marks of the camshaft timing gears are as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 11324 14.INSTALL TIMING CHAIN COVER PLATE

a.
A250986

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15.INSTALL TIMING CHAIN COVER TIGHT PLUG

Hide 11201 16.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 82121 18.CONNECT ENGINE WIRE

a.
A268654N01
1.302,3.958 1.438,4.104 0.135,0.146 10 true A 0.063,0.479 0.271,0.656 0.208,0.177 10 false B 1.146,0.99 1.271,1.167 0.125,0.177 10 true B 3.24,1.177 3.406,1.333 0.167,0.156 10 false B

Install the engine wire to the engine with the bolts and nuts.

Torque:
Nut A : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the connectors and clamps.


Hide 12309 19.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

Hide 12327A 20.INSTALL NO. 2 ENGINE MOUNTING STAY RH

Hide 21.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 22.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 23.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 24.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 26.INSPECT FOR OIL LEAK

Hide 53736 27.INSTALL FRONT FENDER APRON SEAL RH

Hide 51441C 28.INSTALL ENGINE UNDER COVER RH

Hide 53851Z 29.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 12601B 30.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 31.INSTALL FRONT WHEEL RH