Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE UNIT
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073932 ENGINE UNIT A

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.
A198197C07
2.374,2.431 2.555,2.586 0.181,0.155 10 *a
*a Protrusion Height


Using a plastic-faced hammer, tap in 2 new ring pins until they stop.

Standard protrusion height:

4.3 to 5.3 mm (0.169 to 0.209 in.)



Hide 13620B 2.INSTALL ENGINE BALANCER ASSEMBLY

a.
A198170C08
2.167,0.99 1.438,0.833 1.438,0.833 2.167,1.104 true 1.26,0.708 1.438,0.906 0.177,0.198 10 true *a
*a Alignment Mark


Check that the alignment marks of the balance shaft damper cover and balance shaft driven gear are aligned.

If the alignment marks are not aligned, realign them.

i.
A198171C08
1.177,0.917 1.313,0.917 1.313,0.917 1.563,1.198 true 2.208,1.281 2.635,1.583 2.635,1.583 2.292,1.156 true 1.156,1.688 1.302,1.688 1.302,1.688 1.667,1.552 true 0.969,0.823 1.167,0.979 0.198,0.156 10 true *1 0.958,1.635 1.146,1.813 0.188,0.177 10 false *2 2.677,1.594 2.875,1.771 0.198,0.177 10 true *a
*1 Driven Gear
*2 Damper Cover
*a Alignment Mark


Place a wrench on the rear cutout part of the No. 2 balance shaft and secure the shaft in place.


ii.

Rotate the balance shaft driven gear of the No. 1 balance shaft counterclockwise to align the alignment mark of the balance shaft driven gear with the alignment mark of the balance shaft damper cover.



b.
A196927N07
0.927,1.406 1.094,1.573 0.167,0.167 10 true 1 2.615,0.188 2.729,0.365 0.115,0.177 10 true 2 2.719,1.688 2.844,1.833 0.125,0.146 10 true 3

Install the engine balancer to the stiffening crankcase with the 3 bolts, and tighten the bolts in the sequence shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 3.INSTALL STIFFENING CRANKCASE STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

Using an E5 and E8 "TORX" socket wrench, install the stud bolts.

A198166C06
5.063,0.385 4.76,0.74 false 5.146,1.802 4.76,2.083 false 5.104,1.417 4.76,1.146 false 5.156,2.615 4.76,2.375 false 5.198,1.719 6.427,1.917 1.229,0.198 10 false 8.5 mm (0.335 in.) 5.229,2.563 6.49,2.771 1.26,0.208 10 false 8.0 mm (0.315 in.) 5.385,2.167 6.583,2.354 1.198,0.188 10 false 18 mm (0.709 in.) 2.26,1.063 2.375,1.219 0.115,0.156 10 false A 4.146,0.115 4.26,0.271 0.115,0.156 10 false A 1.063,1.875 1.208,2.021 0.146,0.146 10 false B 1.625,2.271 1.729,2.427 0.104,0.156 10 true B 4.156,1.646 4.302,1.792 0.146,0.146 10 false B 5.135,1.344 6.281,1.573 1.146,0.229 10 false 13 mm (0.512 in.) 5.115,0.26 6.26,0.5 1.146,0.24 10 false 20 mm (0.787 in.) 5.365,0.813 6.531,1.021 1.167,0.208 10 false 35 mm (1.38 in.) 0.208,0 0.396,0.167 0.188,0.167 10 false *a 0.208,1.302 0.396,1.49 0.188,0.188 10 false *b
*a Front Side *b Lower Side


Torque:
for Stud Bolt A : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
for Stud Bolt B : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 11420 4.INSTALL STIFFENING CRANKCASE ASSEMBLY

a.
A198168C06
0.771,0.646 1.5,1.052 true 0.583,0.552 0.75,0.74 0.167,0.188 10 false *a 1.188,1.563 1.427,1.729 0.24,0.167 10 true 90°
*a Key


Rotate the crankshaft clockwise so that the crankshaft key is at the position 90° from the bottom as shown in the illustration.


b.
A258254C07
2.094,1.01 1.771,0.281 1.771,0.281 1.667,0.281 true 0.771,0.167 1.792,0.396 1.021,0.229 10 false 2.5 to 3.5 mm 3,0.531 3.219,0.76 0.219,0.229 10 false A 1.177,3.604 1.365,3.813 0.188,0.208 10 false A 0.354,4.094 1.427,4.333 1.073,0.24 10 false 2.5 to 3.5 mm 2.104,3.688 3.188,3.948 1.083,0.26 10 false 7.0 to 9.0 mm
V100145

Stiffening Crankcase
V100146

Cylinder Block


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Dimension:
Area Specified Condition
Continuous Line 2.5 to 3.5 mm (0.0984 to 0.138 in.)
Dashed Line 7.0 to 9.0 mm (0.276 to 0.354 in.) wide and 2.5 to 3.5 mm (0.0984 to 0.138 in.) thick


Application Length A:

28 mm (1.10 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.

·

Do not apply oil for at least 2 hours after the installation.




c.
A285537C04
1.417,0.979 1.208,0.302 1.208,0.302 1.99,0.99 false 1.083,0.125 1.396,0.281 0.313,0.156 10 *a
*a Cutout


Check that the rear cutout parts are as shown in the illustration.


d.

Clean the bolts and their installation holes.


e.
A198186C07
1.545,0.47 1.708,0.647 0.163,0.177 10 *1 1.742,0.557 2.086,0.832 false
*1 Adhesive


Apply adhesive to 3 or more threads of the ends of bolts A.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.
A198172N05
0.698,0.25 0.813,0.406 0.115,0.156 10 false A 0.948,1.948 1.063,2.104 0.115,0.156 10 false A 2.719,0.031 2.865,0.177 0.146,0.146 10 false B 2.948,1.844 3.094,1.99 0.146,0.146 10 false B 2.865,0.844 3.01,0.99 0.146,0.146 10 true C 2.573,1.927 2.719,2.073 0.146,0.146 10 false C 2.854,1.083 2.979,1.219 0.125,0.135 10 true C 2.313,0.052 2.458,0.208 0.146,0.156 10 false D 2.198,1.031 2.323,1.188 0.125,0.156 10 true D 1.646,1.979 1.76,2.135 0.115,0.156 10 true D 1.49,0 1.625,0.146 0.135,0.146 10 true D

Temporarily install the stiffening crankcase with the 11 bolts.

Bolt Length :
Item Length
Bolt A 65 mm (2.56 in.)
Bolt B 35 mm (1.38 in.)
Bolt C 125 mm (4.92 in.)
Bolt D 165 mm (6.50 in.)


HINT:

Apply adhesive to bolts A before installation.



g.
A198172N06
2.833,1.073 2.938,1.219 0.104,0.146 10 true 9 2.542,1.948 2.635,2.104 0.094,0.156 10 false 1 2.333,0.042 2.458,0.219 0.125,0.177 10 false 2 2.208,1.031 2.323,1.177 0.115,0.146 10 true 3 2.719,0.042 2.813,0.198 0.094,0.156 10 false 4 2.969,1.854 3.083,2 0.115,0.146 10 false 5 1.542,0.021 1.656,0.177 0.115,0.156 10 true 6 1.677,1.979 1.802,2.125 0.125,0.146 10 true 7 2.833,0.875 2.927,1.021 0.094,0.146 10 true 8 0.604,0.25 0.781,0.396 0.177,0.146 10 false 10 0.865,1.938 1.042,2.083 0.177,0.146 10 false 11

Tighten the 11 bolts in the sequence shown in the illustration to install the stiffening crankcase

Torque:
for Bolt A : 24 N*m (245 kgf*cm, 18 ft.*lbf)
except Bolt A : 43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12121 5.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A196920N03
1.135,0.563 1.26,0.708 0.125,0.146 10 true 1 2.083,1.948 2.177,2.125 0.094,0.177 10 false 2 0.635,0.844 0.75,0.99 0.115,0.146 10 true 3 1.479,1.948 1.604,2.104 0.125,0.156 10 true 4 1.219,0.188 1.333,0.344 0.115,0.156 10 true 5

Install the oil pan baffle plate and uniformly tighten the 5 bolts in several steps, in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new gasket.


b.
A198187C02
1.635,0.365 2.115,0.625 false 1.417,0.25 1.594,0.438 0.177,0.188 10 false *a 0.573,1.927 0.708,2.083 0.135,0.156 10 true 1 0.646,3.052 0.74,3.229 0.094,0.177 10 true 2 2.146,2.99 2.26,3.135 0.115,0.146 10 true 3
*a Protrusion


Align the protrusion of the gasket with the cutout of the oil strainer, and install the gasket to the oil strainer.


c.

Install the oil strainer with the 3 bolts in several steps, in the sequence shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12101 7.INSTALL OIL PAN SUB-ASSEMBLY

a.
A210205N05
1.5,1.656 1.844,1.656 false 0.563,1.583 1.552,1.75 0.99,0.167 10 false 2.5 to 3.5 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.

·

Do not apply oil for at least 2 hours after the installation.




b.
A210204C09
0.76,1.208 1.771,1.427 1.771,1.427 1.49,1.823 false 1.833,1.354 2.01,1.5 0.177,0.146 10 false *1 2.042,0 2.313,0.156 0.271,0.156 10 false 1, 9 1.104,2 1.469,2.156 0.365,0.156 10 false 2, 15 0.823,1.938 0.938,2.083 0.115,0.146 10 false 3 0.427,1.625 0.521,1.781 0.094,0.156 10 false 4 0.385,1.01 0.5,1.156 0.115,0.146 10 false 5 0.708,0.708 0.823,0.865 0.115,0.156 10 false 6 0.99,0.5 1.083,0.635 0.094,0.135 10 true 7 1.146,0.063 1.24,0.208 0.094,0.146 10 false 8 2.313,0.292 2.49,0.438 0.177,0.146 10 false 10 2,2 2.177,2.146 0.177,0.146 10 false 14 2.458,1.76 2.635,1.906 0.177,0.146 10 false 13 2.583,1.146 2.76,1.292 0.177,0.146 10 true 12 2.583,0.729 2.76,0.875 0.177,0.146 10 true 11 1.583,1.833 1.698,1.99 0.115,0.156 10 true A 1.688,0.083 1.833,0.229 0.146,0.146 10 false A
*1 Nut


Install the oil pan with the 11 bolts and 2 nuts in several steps, in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Bolt A and nut A are tightened twice.



Hide 15620 8.INSTALL OIL FILTER CAP ASSEMBLY

Hide 11445 10.INSTALL CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Install the water jacket spacer to the cylinder block.


Hide 11101 12.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13050 13.SET CAMSHAFT TIMING GEAR ASSEMBLY

Hide 11151A 14.INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.
A198195C09
2.422,1.604 2.595,1.757 0.172,0.152 10 *a
*a Protrusion Height


Using a plastic-faced hammer, tap in 10 new ring pins to the camshaft housing.

Standard protrusion height:

2.7 to 3.3 mm (0.106 to 0.130 in.)



Hide 11114A 15.INSTALL CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A198194C07
2.109,1.583 2.27,1.739 0.162,0.156 10 *a
*a Protrusion Height


Using a plastic-faced hammer, tap in 2 new straight pins to the camshaft housing.

Standard protrusion height:

5.0 to 7.0 mm (0.197 to 0.276 in.)



Hide 16.INSTALL CAMSHAFT HOUSING STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A198196N07
1.875,1.688 1.75,1.688 1.75,1.688 1.531,2.271 false 1.531,2.802 1.896,3.25 1.896,3.25 2.125,3.25 false 2.167,3.167 3.313,3.396 1.146,0.229 10 false 13 mm (0.512 in.) 1.948,1.594 3.094,1.833 1.146,0.24 10 false 20 mm (0.787 in.) 2.25,2.375 3.375,2.573 1.125,0.198 10 false 35 mm (1.38 in.)

Using an E8 "TORX" socket wrench, install the stud bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11811 17.INSTALL NO. 1 CAMSHAFT BEARING

a.
A198176C07
1.833,2.26 1.969,2.594 1.969,2.594 2.063,2.594 false 0.135,2.385 0.271,2.552 0.135,0.167 10 false A 1.625,2.385 1.76,2.552 0.135,0.167 10 false B 2.104,2.51 2.281,2.677 0.177,0.167 10 false *1
*1 Vernier Caliper


Clean the No. 1 camshaft bearing.


b.

Install the camshaft bearing to the No. 1 camshaft bearing cap.


c.

Using a vernier caliper, measure the distance between the camshaft bearing cap edge and the camshaft bearing edge.

Standard dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



Hide 11821 18.INSTALL NO. 2 CAMSHAFT BEARING

a.

Clean the No. 2 camshaft bearing.


b.

Install the camshaft bearing to the camshaft housing.


c.
A198177C11
0.917,1.313 0.823,1.313 0.823,1.313 0.74,2.531 false 0.854,2.333 0.99,2.5 0.135,0.167 10 false A 0.979,1.198 1.167,1.385 0.188,0.188 10 false *1
*1 Vernier Caliper


Using a vernier caliper, measure the distance between the camshaft housing edge and the camshaft bearing edge.

Standard distance:

1.15 to 1.85 mm (0.0453 to 0.0728 in.)



Hide 15678A 19.INSTALL OIL CONTROL VALVE FILTER

a.
A196915

Install the oil control valve filter to the No. 1 camshaft bearing cap.


Hide 13750 23.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 24.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11103 25.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13050 26.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 27.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13521 28.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A196881

Install the crankshaft timing sprocket to the crankshaft.


Hide 13561 31.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13540 34.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 36.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11324 37.INSTALL TIMING CHAIN COVER PLATE

a.
A196860

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 38.INSTALL TIMING CHAIN COVER TIGHT PLUG

a.
A196859

Using a 14 mm hexagon wrench, install a new gasket and the plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 11302 39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 12315A 40.INSTALL ENGINE MOUNTING BRACKET RH

Hide 11301C 41.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 11193 42.INSTALL SPARK PLUG TUBE GASKET

a.
A196890

Install 4 new plug tube gaskets to the cylinder head cover sub-assembly.

NOTICE:

After pressing in the spark plug tube gasket, make sure the gasket protrudes 1.0 mm (0.0394 in.) or less from the cylinder head cover sub-assembly.



Hide 11201 43.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A196857

Apply a light coat of engine oil to 3 new gaskets.


b.

Install the 3 gaskets to the camshaft bearing caps.


c.

Install a new gasket to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surface.



d.
A196891C08
0.545,1.986 0.728,2.148 0.183,0.162 10 *1 2.193,1.854 2.382,2.038 0.189,0.184 10 *1 2.134,1.942 1.996,1.943 1.996,1.943 1.763,2.484 false 0.909,2.283 1.112,2.452 0.203,0.168 10 *2 2.49,2.28 2.686,2.444 0.196,0.165 10 *3 1.133,2.395 1.233,2.395 1.233,2.395 1.295,2.67 false 2.44,2.369 2.294,2.369 2.294,2.369 2.151,2.692 false 1.485,2.947 1.621,3.11 0.135,0.163 10 A 1.786,2.947 1.922,3.11 0.135,0.163 10 A
*1 Seal Packing
*2 Timing Chain Cover
*3 Camshaft Housing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


Application width A:

5.0 mm (0.197 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




e.
A293102N04
0.531,0.177 0.615,0.177 0.615,0.177 0.688,0.469 false 3.042,1.365 3.125,1.292 3.125,1.292 3.198,1.292 false 1.688,0.75 2.01,0.906 0.323,0.156 10 true 1, 19 2.844,0.781 3.365,0.969 0.521,0.188 10 false 3, 21 1.677,0.115 2.198,0.302 0.521,0.188 10 false 4, 12 1.479,1.969 2,2.156 0.521,0.188 10 false 5, 18 0.74,0.76 1.073,0.917 0.333,0.156 10 true 2, 20 0.25,0.24 0.406,0.438 0.156,0.198 10 false 9 0.229,1.833 0.385,2.031 0.156,0.198 10 false 7 1.115,1.969 1.271,2.167 0.156,0.198 10 false 6 3.208,1.771 3.427,1.979 0.219,0.208 10 false 16 2.177,1.979 2.49,2.177 0.313,0.198 10 false 17 3.219,0.875 3.427,1.083 0.208,0.208 10 false 15 3.063,0.281 3.344,0.5 0.281,0.219 10 false 14 2.198,0.104 2.469,0.323 0.271,0.219 10 false 13 1.292,0.125 1.573,0.313 0.281,0.188 10 false 11 0.76,0.073 1,0.281 0.24,0.208 10 false 10 0.396,0.104 0.552,0.302 0.156,0.198 10 false A 3.25,1.208 3.406,1.406 0.156,0.198 10 false B 0.094,0.979 0.25,1.177 0.156,0.198 10 false 8

Align the cylinder head cover with pin A. Then align the cylinder head cover with pin B and install the cylinder head cover sub-assembly.


f.

Install 3 new seal washers and the 16 bolts, and then tighten the bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not apply oil for at least 2 hours after the installation.



Hide 13471 44.INSTALL CRANKSHAFT PULLEY

a.
A305738C02
1.313,0.927 0.875,0.875 0.875,0.875 1.198,0.635 true 0.833,0.208 1.146,0.365 0.313,0.156 10 false *a 2.26,1.688 2.573,1.844 0.313,0.156 10 false *b 0.542,0.802 1,1 0.458,0.198 10 false SST
*a Hold
*b Turn


Align the pulley set key with the key groove of the crankshaft pulley.


b.

Using SST, hold the crankshaft pulley and install the pulley bolt.

SST
09213-54015  
09330-00021  

Torque:
260 N*m (2650 kgf*cm, 192 ft.*lbf)

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



Hide 11301K 45.INSTALL CRANKSHAFT POSITION SENSOR

Hide 16323 46.INSTALL WATER INLET HOUSING

a.
A195872

Install a new gasket and the water inlet housing with the 4 bolts and nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 15710 47.INSTALL OIL COOLER ASSEMBLY (w/ Oil Cooler)

Hide 16100 48.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 16620 49.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A196670

Install the V-ribbed belt tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16331A 50.INSTALL THERMOSTAT

Hide 16321 51.INSTALL WATER INLET

Hide 16268 52.INSTALL NO. 1 WATER BY-PASS PIPE

a.
A194876

Install a new gasket and the No. 1 water by-pass pipe with the 2 nuts and bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12215 53.INSTALL SEPARATOR CASE

a.
A210188

Apply a light coat of engine oil to a new gasket.


b.

Install the gasket to the separator case.


c.

Install the separator case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12205 54.INSTALL VENTILATION CASE SUB-ASSEMBLY

a.
A210187N06
1.394,1.795 2.298,1.951 0.903,0.156 10 2.5 to 3.5 mm 1.364,1.887 1.248,1.887 1.248,1.887 1.035,1.603 false

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A210185N02
0.49,1.323 0.583,1.323 0.583,1.323 0.792,1.427 true 2.719,0.573 2.531,0.573 true 0.896,0 1.094,0.167 0.198,0.167 10 false 10 1.542,0.031 1.719,0.198 0.177,0.167 10 true 11 2.813,0.094 3.135,0.25 0.323,0.156 10 true 2, 12 0.198,1.708 0.469,1.875 0.271,0.167 10 true 1, 8 3.052,0.906 3.156,1.073 0.104,0.167 10 true 3 2.938,1.708 3.052,1.896 0.115,0.188 10 true 4 1.917,1.927 2.021,2.094 0.104,0.167 10 true 5 0.365,0.281 0.563,0.458 0.198,0.177 10 true 9 1.021,1.667 1.125,1.833 0.104,0.167 10 true 7 1.271,1.927 1.375,2.094 0.104,0.167 10 true 6 2.76,0.49 2.885,0.656 0.125,0.167 10 true A 0.365,1.25 0.49,1.417 0.125,0.167 10 true A

Install the ventilation case, and install the 8 bolts and 2 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Bolt A is tightened twice.



Hide 12204 55.INSTALL VENTILATION VALVE SUB-ASSEMBLY

Hide 11102A 56.INSTALL CAMSHAFT POSITION SENSOR

Hide 11101J 57.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 12108 58.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install a new gasket to the oil filler cap.


b.

Install the oil filler cap to the cylinder head.


Hide 60.INSTALL ENGINE COVER JOINT

a.
A196900

Install the 3 joints.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)