Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073988 TRANSMISSION CONTROL CABLE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.


a.

Pass the transmission control cable assembly from the cabin to the engine compartment.


b.

Install the transmission control cable assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Install the dash panel insulator to the original position.


d.

Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.


e.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.



f.

Connect the wire harness clamp.


g.

Engage the 2 claws to connect the transmission control cable assembly.


h.
C194520C18
2.26,2.573 2.583,2.573 false 1.948,1.75 2.094,1.5 2.094,1.5 2.198,1.5 false 1.615,0.958 1.802,1.135 0.188,0.177 10 *a 1.792,1.344 1.979,1.521 0.188,0.177 10 *a 2.438,0.781 2.625,0.958 0.188,0.177 10 *b 2.229,1.427 2.417,1.604 0.188,0.177 10 *1 2.229,2.313 2.417,2.49 0.188,0.177 10 *b 2.625,2.49 2.813,2.667 0.188,0.177 10 *2
*1 Slider
*2 Lock Piece
*a Slide
*b Pull


Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.


i.
C239661C12
1.207,2.686 1.058,2.516 1.058,2.516 0.968,2.516 false 0.772,2.442 0.93,2.6 0.158,0.158 10 *1
*1 Lock Piece


Install the end of the transmission control cable to the lower shift lever assembly.

NOTICE:
·

Check that the lock piece is pulled up.

·

Install the cable end all the way to the base of the pin.




j.

Push the lock piece into the adjuster case.

NOTICE:
·

Check that the park/neutral position switch and the shift lever are in neutral.

·

Securely push in the lock piece until the slider lock is engaged.




Hide 33820B 2.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.


a.

Pass the transmission control cable assembly from the cabin to the engine compartment.


b.

Install the transmission control cable assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Install the dash panel insulator to the original position.


d.

Install the No. 1 parking brake cable assembly with the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.

Install the floor carpet to the original position.


f.

Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.


g.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.



h.

Connect the wire harness clamp.


i.

Engage the 2 claws to connect the transmission control cable assembly.


j.
C194520C18
2.26,2.573 2.583,2.573 false 1.948,1.75 2.094,1.5 2.094,1.5 2.198,1.5 false 1.615,0.958 1.802,1.135 0.188,0.177 10 *a 1.792,1.344 1.979,1.521 0.188,0.177 10 *a 2.438,0.781 2.625,0.958 0.188,0.177 10 *b 2.229,1.427 2.417,1.604 0.188,0.177 10 *1 2.229,2.313 2.417,2.49 0.188,0.177 10 *b 2.625,2.49 2.813,2.667 0.188,0.177 10 *2
*1 Slider
*2 Lock Piece
*a Slide
*b Pull


Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.


k.
C241614C04
1.258,2.264 1.437,2.085 1.437,2.085 1.57,2.085 false 1.606,1.978 1.899,2.17 0.294,0.192 10 *1
*1 Lock Piece


Install the end of the transmission control cable to the lower shift lever assembly.

NOTICE:
·

Check that the lock piece is pulled up.

·

Install the cable end all the way to the base of the pin.




l.

Push the lock piece into the adjuster case.

NOTICE:
·

Check that the park/neutral position switch and the shift lever are in neutral.

·

Securely push in the lock piece until the slider lock is engaged.




Hide 46410 3.CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)

a.

Install the No. 1 parking brake cable assembly with the bolt and nut.

Torque:
Bolt : 15 N*m (153 kgf*cm, 11 ft.*lbf)
Nut : 5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Install the floor carpet to the original position.


Hide 78110K 4.INSTALL ACCELERATOR PEDAL SENSOR ASSEMBLY (for LHD)

Hide 6.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 7.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 8.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 9.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 12601B 10.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY