Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074130 ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (engine switch off, or driver door is opened and closed with engine switch on (IG)).

·

w/ Theft Deterrent System:

The certification ECU (smart key ECU assembly) receive the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is arming preparation state or alarm sounding state. Then, certification ECU (smart key ECU assembly) blinks the security indicator light.


WIRING DIAGRAM

B278947E25
5.063,1.74 6.698,2.125 1.635,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 2.813,1.781 4.333,2.188 1.521,0.406 10 false Certification ECU (Smart Key ECU Assembly) 2.813,1.625 3.115,1.781 0.302,0.156 10 false I78 0.51,1.594 2.406,1.927 1.896,0.333 10 false Security Indicator Light (Heater Control Switch Board) 0.573,2.469 2.479,2.729 1.906,0.26 10 false : CAN Communication Line 0.51,1.438 0.906,1.729 0.396,0.292 10 false I56 1.031,0.906 1.552,1.25 0.521,0.344 10 false GND 0.854,0.781 1.063,0.99 0.208,0.208 10 false 6 2.969,0.792 3.281,1.083 0.313,0.292 10 false 18 2.042,0.792 2.24,0.99 0.198,0.198 10 false 1 3.198,0.906 3.573,1.063 0.375,0.156 10 false IND 3.688,0.906 4.021,1.063 0.333,0.156 10 false CAN 5.479,0.906 5.958,1.24 0.479,0.333 10 false CAN 1.792,0.906 2.073,1.083 0.281,0.177 10 false LP

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

The engine immobiliser system (w/ Smart Entry and Start System) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the engine immobiliser system (w/ Smart Entry and Start System) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light operates normally.



Result:
Result Proceed to
OK (w/ Theft Deterrent System) A
OK (w/o Theft Deterrent System) B
NG C



A

2.CHECK SECURITY INDICATOR LIGHT OPERATION

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on normally.



Result:
Result Proceed to
*1 is NG (*2 is OK) A
*2 is NG (*1 is OK) B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I56 security indicator light (heater control switch board) connector.


b.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-18 (IND)- I56-1 (LP) Always Below 1 Ω
I78-18 (IND) - Body ground Always 10 kΩ or higher
I56-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and check the pulse according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I56-1 (LP) - I56-6 (GND) Engine switch off → Engine switch on (IG) Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)