Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM
RM19V0EQ _59 Vehicle Exterior _014616 WINDOW / GLASS _0074216 WINDOW DEFOGGER SYSTEM J

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  Rear Window Defogger System does not Operate  


DESCRIPTION

When the rear window defogger switch on the air conditioning control assembly*1 or air conditioning control assembly (heater control switch board)*2 is pressed, the operation signal is transmitted to the air conditioning amplifier assembly through a LIN communication line. When the air conditioning amplifier assembly receives the signal, it turns on the engine room junction block assembly to operate the rear window defogger.

*1: for Manual Air Conditioning System

*2: for Automatic Air Conditioning System


WIRING DIAGRAM

B281019E06
0.958,5.406 2.583,5.552 1.625,0.146 10 false : LIN Communication Line 4.844,4.708 7.073,4.885 2.229,0.177 10 false Air Conditioning Amplifier Assembly 1.427,4.5 3.698,4.667 2.271,0.167 10 false Air Conditioning Control Assembly*1 2.052,3.031 4.531,3.177 2.479,0.146 10 false Engine Room Junction Block Assembly 4.646,0.875 6.26,1.021 1.615,0.146 10 false Radio Setting Condenser 4.833,1.844 6.573,2.25 1.74,0.406 10 false Rear Window Defogger Wire (Back Window Glass) 6.177,1.542 6.542,1.75 0.365,0.208 10 false N29 4.74,1.542 5.01,1.771 0.271,0.229 10 false P1 4.646,0.677 4.938,0.844 0.292,0.167 10 false N28 5.167,0.438 5.563,0.604 0.396,0.167 10 false DEF+ 4.781,1.354 4.906,1.51 0.125,0.156 10 false 1 6.25,1.354 6.375,1.51 0.125,0.156 10 false 1 3.573,0.344 3.698,0.5 0.125,0.156 10 false 1 3.531,0.542 3.875,0.802 0.344,0.26 10 false 1N 3.521,2.729 3.854,2.969 0.333,0.24 10 false 1F 3.573,2.531 3.688,2.688 0.115,0.156 10 false 4 0.125,0.74 0.958,0.906 0.833,0.167 10 false from Battery 0.302,1.802 0.875,2.313 0.573,0.51 10 false from IG1 NO. 2 Relay 5.469,4.063 5.729,4.208 0.26,0.146 10 false LIN 2.802,4.063 3.063,4.208 0.26,0.146 10 false LIN 5.469,2.74 5.906,2.885 0.438,0.146 10 false RDFG 5.24,2.635 5.427,2.792 0.188,0.156 10 false 38 4.844,4.563 5.125,4.729 0.281,0.167 10 false I77 1.427,4.365 1.719,4.531 0.292,0.167 10 false I56 6.031,3.833 6.365,3.979 0.333,0.146 10 false GND 6.396,3.698 6.688,3.917 0.292,0.219 10 false 14 3.031,2.74 3.542,2.969 0.51,0.229 10 false DEFS 3.021,0.542 3.427,0.698 0.406,0.156 10 false RDEF 2.615,0.76 2.917,0.917 0.302,0.156 10 false ALT 2.604,1.771 2.875,1.927 0.271,0.156 10 false IGN 2.583,2.229 3.01,2.385 0.427,0.156 10 false GND1 2.583,2.688 3.01,2.844 0.427,0.156 10 false GND2 2.292,2.677 2.604,2.917 0.313,0.24 10 false 1G 2.354,2.479 2.479,2.635 0.125,0.156 10 false 4 2.354,2.031 2.531,2.188 0.177,0.156 10 false 3 2.323,1.563 2.5,1.719 0.177,0.156 10 false 15 2.302,2.229 2.563,2.417 0.26,0.188 10 false 1F 2.302,1.771 2.583,2.021 0.281,0.25 10 false 1F 2.354,0.552 2.552,0.75 0.198,0.198 10 false 1 2.354,0.75 2.479,0.906 0.125,0.156 10 false B 0.125,1.24 0.958,1.406 0.833,0.167 10 false from Battery 2.615,1.26 3.021,1.417 0.406,0.156 10 false BATT 2.354,1.052 2.563,1.24 0.208,0.188 10 false 1 2.354,1.25 2.479,1.406 0.125,0.156 10 false A 1.198,1.927 2.198,2.073 1,0.146 10 false ECU-IG1 NO. 1 1.427,4.813 3.521,5.24 2.094,0.427 10 false Air Conditioning Control Assembly (Heater Control Switch Board)*2 4.271,5.052 6.917,5.229 2.646,0.177 10 false *1: for Manual Air Conditioning System 4.271,5.313 6.865,5.479 2.594,0.167 10 false *2: for Automatic Air Conditioning System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the battery voltage becomes low, rear window defogger operation is canceled to prioritize supplying power to the power steering system.



PROCEDURE

1.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

HINT:

Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly through the same communication line.


OK:

The air conditioning system operates normally.



Result:
Result Proceed to
OK A
NG (for Manual air conditioning system) B
NG (for Automatic air conditioning system) C



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEFOGGER RELAY)

B

C

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEFOGGER RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger Relay (Rear) Rear window defogger OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Defogger Relay (Rear)
50004 121 22
OK:

The rear window defogger system operates normally.



Result:
Result Proceed to
NG A
OK (for Manual air conditioning system) B
OK (for Automatic air conditioning system) C



A

3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

B

C

REPLACE AIR CONDITIONING CONTROL ASSEMBLY (HEATER CONTROL SWITCH BOARD)

3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Using a voltmeter, check the signal reading of the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)

NG

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)
a.

Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

E230000C07
2.781,2.615 3.094,2.813 0.313,0.198 4.729,2.708 5.042,2.906 0.313,0.198 6.188,3.094 6.5,3.292 0.313,0.198 0.771,3.073 1.083,3.271 0.313,0.198 5.104,3.656 5.271,3.979 false 0.865,3.583 0.792,3.896 false 2.646,3.677 2.583,4.125 false 6.281,3.625 6.219,3.948 false 2.854,2.646 3.073,2.844 0.219,0.198 10 1F 4.792,2.729 5.01,2.927 0.219,0.198 10 1G 6.281,3.115 6.406,3.26 0.125,0.146 10 A 0.875,3.094 1,3.26 0.125,0.167 10 B 0.271,0.208 0.479,0.406 0.208,0.198 10 *a 6.083,3.969 6.479,4.156 0.396,0.188 10 BATT 5.115,4 5.573,4.188 0.458,0.188 10 GND2 2.375,4.146 2.802,4.313 0.427,0.167 10 GND1 0.646,3.927 0.938,4.115 0.292,0.188 10 ALT
*a Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (BATT) - Body ground Always 11 to 14 V
B-1 (ALT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-3 (GND1) - Body ground Always Below 1 Ω
1G-4 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Disconnect the 1F engine room junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-38 (RDFG) - 1F-4 (DEFS) Always Below 1 Ω
1F-4 (DEFS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Reconnect the 1F engine room junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I77-38 (RDFG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
B274526C02
1.25,0.073 1.656,0.333 0.406,0.26 0.75,1.021 0.385,1.625 false 1.104,0.917 1.615,1.615 false 0.135,0.115 0.323,0.281 0.188,0.167 10 *a 1.354,0.125 1.677,0.292 0.323,0.167 10 I77 1.563,1.635 1.917,1.802 0.354,0.167 10 GND 0.198,1.656 0.615,1.823 0.417,0.167 10 RDFG
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Reconnect the I77 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I77-38 (RDFG) - I77-14 (GND) Ignition switch ON, rear window defogger switch off 11 to 14 V
I77-38 (RDFG) - I77-14 (GND) Ignition switch ON, rear window defogger switch on Below 2.2 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - REAR WINDOW DEFOGGER WIRE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - REAR WINDOW DEFOGGER WIRE)
a.

Disconnect the N29 rear window defogger wire (back window glass) battery side connector.


b.

Disconnect the 1N engine room junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1N-1 (RDEF) - N29-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Reconnect the 1N engine room junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N29-1 - Body ground Ignition switch ON, rear window defogger switch on 11 to 14 V
N29-1 - Body ground Ignition switch ON, rear window defogger switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER WIRE - BODY GROUND)

NG

REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER WIRE - BODY GROUND)
a.

Disconnect the P1 rear window defogger wire (back window glass) ground side connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P1-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE REAR WINDOW DEFOGGER WIRE (BACK WINDOW GLASS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR