Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074102 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1273 Sliding Roof ECU Communication Stop No communication between sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Sliding roof ECU (sliding roof drive gear sub-assembly)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

S/ROOF fuse



WIRING DIAGRAM

B315277
4.25,1.802 6.156,2.313 1.906,0.51 10 Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 4.25,1.656 4.927,2.073 0.677,0.417 10 S4 4.552,0.333 4.792,0.469 0.24,0.135 10 11 2.167,0.313 2.677,0.677 0.51,0.365 10 16 3.135,0.313 3.667,0.75 0.531,0.438 10 30 5.74,0.344 6.177,0.719 0.438,0.375 10 8 5.719,1.198 6.156,1.49 0.438,0.292 10 12 4.771,0.469 5.594,0.917 0.823,0.448 10 MPX1 1.792,0.469 2.302,0.719 0.51,0.25 10 LIN2 0.625,0.854 1.01,1.094 0.385,0.24 10 MB 0.625,1.021 2.292,1.5 1.667,0.479 10 Main Body ECU (Multiplex Network Body ECU) 0.573,1.667 1.042,1.969 0.469,0.302 10 3B 0.563,1.802 3.573,2.406 3.01,0.604 10 Instrument Panel Junction Block Assembly 0.448,2.469 2.292,2.781 1.844,0.313 10 : LIN Communication Line 5.531,0.469 5.896,0.844 0.365,0.375 10 B 5.542,1.292 5.948,1.635 0.406,0.344 10 E 6.125,0.563 6.979,1.052 0.854,0.49 10 S/ROOF 2.771,0.313 3.281,0.563 0.51,0.25 10 LIN2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).

·

When using the intelligent tester to troubleshoot with the ignition switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B281983
1.813,0.917 2.177,1.188 0.365,0.271 5.49,0.844 5.854,1.115 0.365,0.271 1.802,2.188 2.052,1.74 false 5.615,2.271 5.865,1.833 false 1.896,0.969 2.208,1.167 0.313,0.198 10 MB 5.604,0.896 5.917,1.094 0.313,0.198 10 3B 0.406,0.375 0.719,0.573 0.313,0.198 10 *a 4.792,0.458 5.104,0.656 0.313,0.198 10 *b 1.667,2.219 2.281,2.417 0.615,0.198 10 LIN2 5.448,2.302 6.063,2.5 0.615,0.198 10 LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Instrument Panel Junction Block Assembly)



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3B-30 (LIN2) - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU)
a.

Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-30 (LIN2) - S4-11 (MPX1) Always Below 1 Ω
3B-30 (LIN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S4-8 (B) - S4-12 (E) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S4-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Replace the sliding roof ECU (sliding roof drive gear sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1273 is not output.



Result:
Proceed to
OK
NG



OK

END (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)